I love your idea for the back up drain. I have a similar (much more modest!) set up but the moving bed filter sometimes overflows when the silt builds up at the base. I will definitely have a go at building one - thanks for sharing!
Very nice video. You mentioned “siphon” return back to your pond. So the return line is submerged in your pond and this the water flows faster than if it were above water level? I hadn’t thought of that design.
Thank you for sharing. Very impressive. Would you please tell me the purpose and function of the 2 white PVC pipes that run inside and outside the barrel. Thanks
Those are actually just little "legs" of the platform I built to hold the air pump. The air pump is a Hakko 40L and a generic 9" EPDM air diffuser disc.
Are these still in operation after 4 years? I'm looking to build some barrel filters and and am trying to decide on which pumps to use. Are the Periha pump still running?
Thank you for sharing. Do you have a simple schematic for the filter? Where the water enters the barrel and where the water exit to go back to the pond?
I'm running a Periha PB23000 at full power which is supposedly 4500+gph, but I think that ratings are a bit over stated. Air pump is a Hakko 40 which does about 51cfm
@@jcardona1I think your moving bed media drum lends a great starting point to making a protein skimmer for the pond. Try one of those drums with a clamped lid and put a bulkhead at the top of lid with a 2" or 3" line and guaranteed tons of bubbles will come out. It'll be a dual function system
I love your idea for the back up drain. I have a similar (much more modest!) set up but the moving bed filter sometimes overflows when the silt builds up at the base. I will definitely have a go at building one - thanks for sharing!
Cool. I can watch that moving bed all day.
Brother you got that figured out. 😁👌🏼 NICE set up!!
To put it simply... a very smart build :)
Do you have any videos on the construction details of your single barrel system?
I've got a 1/4 ac mud pond with no filtration. I need you to come design my system! nice work.
I had an aquaponics system and it was amazing how much water i got through a bell siphon with a 1/2" standpipe.
Also, what air pump and air stones are you using to move the water to that degree. Thanks
Very nice video. You mentioned “siphon” return back to your pond. So the return line is submerged in your pond and this the water flows faster than if it were above water level? I hadn’t thought of that design.
cool video mate
Thank you for sharing. Very impressive. Would you please tell me the purpose and function of the 2 white PVC pipes that run inside and outside the barrel. Thanks
I was wondering about those two PVC pipes as well. Can't remember if he talked about them in the overview video.
Those are actually just little "legs" of the platform I built to hold the air pump. The air pump is a Hakko 40L and a generic 9" EPDM air diffuser disc.
Hey! Would I be able to just use Uniseals instead of getting the electrical connectors/bulkhead?
And all three returns are 3 inch going out?
Thx!
Can you explain how your underwater returns work? How far below surface do they enter your pond?
How your air pump work good and not much noise,if good please give me the name of the air pump.
Thank you
Are these still in operation after 4 years? I'm looking to build some barrel filters and and am trying to decide on which pumps to use. Are the Periha pump still running?
Still running, both the filter and original pump!
Thank you for sharing. Do you have a simple schematic for the filter? Where the water enters the barrel and where the water exit to go back to the pond?
I got the idea from here
www.koiphen.com/forums/showthread.php?68339-Birdman-s-Fluid-Bed-Filter
Awesome! Is that how the "final" version of the filter? In the overview video you had it a bit different with the third return pipe capped off.
Yes that was the initial setup. These changes I made after that video. I do believe this will be the final layout!
Have you a link for the filter cages/shower drains please?
How much media did the barrel take?
How many kilos of K1 did you put in your 55 gallons filter?
Not sure how much in weight, but it was 4.5cuft
How much media do you have in the 220 L drum. Thanks
It's about 4.5 cuft
what is the pump?
Could you let me know where to find the strainers from can't find them any where
Search on eBay for "suction strainer". Just checked and they're still available
Nice, thanks!
What's your pump flow rate and air flow rate on that 55 gallon drum?
I'm running a Periha PB23000 at full power which is supposedly 4500+gph, but I think that ratings are a bit over stated. Air pump is a Hakko 40 which does about 51cfm
@@jcardona1I think your moving bed media drum lends a great starting point to making a protein skimmer for the pond. Try one of those drums with a clamped lid and put a bulkhead at the top of lid with a 2" or 3" line and guaranteed tons of bubbles will come out. It'll be a dual function system
what type of bulkhead fitting are you using?
They're actually 3" electrical conduit fittings sealed with polyurethane. Cheap and effective bulkheads!
@@jcardona1 thank you. I'll do some research tonight.
@jcardona1 yes, I was seeing that too... much cheaper than bulkhead fittings for sure. No leaks or issues?
Good morning sir, how much media is your filter?
It has about 4.5cuft