Video není dostupné.
Omlouváme se.
HF Ham Radio In My Ford F-150
Vložit
- čas přidán 20. 03. 2024
- Last weekend Shane KI6QFI performed a very professional installation of a High Frequency ham radio into my Ford F-150
See part one (VHF/UHF Radio) here: • Install a VHF/UHF Mobi...
Tools used on the install (As an Amazon Affiliate I earn from qualifying purchases):
Fish Tape: amzn.to/48Zjnjn
Panel Puller: amzn.to/3VoUjPp
Magnetic Work Light: amzn.to/4amDARb
Milwaukee M12 Driver: amzn.to/3vhBFhX
Step bit: amzn.to/4am6MaT
Braided ground strap (from antenna mount): amzn.to/3wXe9qQ
Small pick set: amzn.to/494sfEb
Might Dawn! amzn.to/3wXesC0
Pinecil USB-C & 12 volt soldering iron (Coax connector): amzn.to/494zlII
Here is what's I'm running in my truck:
Breedlove Antenna Mount: breedlovemount...
Yaesu FT-891: www.gigaparts....
Yaesu ATAS-120: www.gigaparts....
Icom 5100: www.gigaparts....
Diesel Power Works Rear Light Antenna Mount: www.dieselpowe...
Lido Mount L-Max Radio Arm: www.lidoradio....
📻 Want the best HT antenna? Signal Stuff Signal Stick signalstuff.co... (This is an affliate link)
📻 Looking for the best deal on the Ed Fong J-Pole? www.kbcubed.co...
📻 The Coax I use is ABR Industries (10% off with code: "abr10hrcc"): abrind.com/?sld=6
📻 I use Ham Radio Deluxe: www.hamradiode...
📻 You can find some of my favorite radios and gear at GigaParts: www.gigaparts....
📻 Good Value HTs: HTs: www.buytwowayr...
📻Check out Radioddity ham radio radios and get a discount: Xiegu G90: radioddity.refr...
📻 Support Ham Radio Crash Course Content 📻
Patreon - / hoshnasi (includes monthly newsletter, stickers and Patron perks)
📸CZcams - / hamradiocrashcourse (includes early access to videos, membership YT badge and custom emojis)
Shop HamTactical: www.hamtactical...
Shop Our Affiliates: hamradiocrashco...
Shop Our Amazon Store: www.amazon.com...
As an Amazon Associate I earn from qualifying purchases.
★ FOLLOW ME HERE ★
🪩 Website………………………► hamradiocrashco...
📸 CZcams..................► / hamradiocrashcourse
💻 Twitch......................► / hamradiocrashcourse
Podcast………………………► hamradiocrashc...
💻 Discord………………….► / discord
📸 Facebook................► goo.gl/cv5rEQ
📸 Twitter.....................► / hoshnasi
📸 Instagram................► / hamradiocrashcourse
📨 Physical Mail...........►Josh Nass P.O Box 5101 Cerritos, CA 90703-5101
Music by Sonic D:
Soundcloud.com/sncd
sncd
Facebook.com/djsonicd
#HRCC #hamradio #amateurradio
that Board under the Carpet tip was Brillant.
That first shot of the "engine compartment" showing the battery location, I was trying to figure out how you'd easily get to that around the motor, then I wondered, where's the motor. That's when I remembered it was an electric truck (thus Lightning). I'm old enough to remember when a Ford F-150 Lightning wasn't electric. Great install and thanks for sharing, I've picked up some tips for my upcoming HF mobile install. Love the board under the carpet most of all. 73, KS5KY
Gonna need an update on that sick roly poly habitat, thanks!
Hey Josh just wanted to take a second to say thanks for all the informative videos. I am down in east San Diego county. I hunt, fish, fly RC planes and I am always on youtube channels/forums pertaining to those hobbies. I'm not sure I have ever come across a channel as informative as yours in any hobby. I got involved with GMRS and got my license after using some radios to stay in contact with my son out quail hunting. That kind of sent me down the rabbit hole and after learning how to program and listen in on the ham repeaters I was all in. I passed my technician test this morning and your video's were a monumental help. Be well, Brian.
Congrats! Thanks for your kind words!!
i like the board under the carpet idea for mounting the radio
Timely video for me. Picking up a new to me truck on Saturday
I've had a half dozen F-150s. Always easier to go out from the cab through that rear vent than trying to go in through the vent. Mount a Rigrunner inside the drivers compartment next to that grommet. Run all your electronics off of that, each one is fused separately.
WTH? Why tease us with a Roly Poly habitat just to make us sit through another mobile radio install??? Give us what we want Josh! :)
Great video Josh and Shane. I have an IC7000 and a Yaesu FTM400 with both radio faces mounted on a Lido L-Max (plus a Target tuner for the Tarheel) in my Ineos Grenadier. Radio bodies are mounted to homebrew mounts tucked behind each front seat with power distribution from a RigRunner board. Routing coax from roof lines on each side was a doozy! It needs a lot of planning and as you showed is very satisfying at the end when it all comes together.
Excellent idea using a board under the carpet. After seeing this, my installation plan in my 2024 Tundra now incudes mounting the main body of my iCom 7000 under my seat using a 1/4 inch sheet of ABS plastic under the carpet. After trimming and heat molding if needed, I will use flat head screws countersunk up through the plastic, then carpet, then the mount with washers and nylock nuts. I also use the crap put of 3M Dual Lock for mic mounts etc.
I did a similar install on my 2020 silverado but I placed the radios under the front seats and yes I used velcro for the install. I also used the breelove mounts. I installed my ft857d 2 years ago and still rockikn. 73.
Breedlove mounts are certainly sturdy!
For the firewall grommet (boot) pass thru... I used a 12" garden hose, cut down the middle, with a flat ish point to push the 1st cable thru. after that just tape to what's going thru already and pull it.
Im gonna be doing this on my lightning with the same antenna. Thanks for the walk through
I did almost the exact set up you did to my 2017, Breedlove mount,tarheel antenna, the same lido mount up front, I did however, drill holes in my floor, passenger side has nothing below it, wish i would have thought of the board! Great idea! Nice job!
The Yaesu Ft-891 with the ATAS-120a is a very nice and easy HF Mobile setup! And the DNR on the 891 is awesome! I had this setup in my Dodge RAM 2500 and now in my VW TDI (Diesel) Jetta Wagon! 73
Just passed my tech and general test yesterday! Excited to get on the air and maybe I’ll catch you in your truck on HF some day :)
Nice clean install Josh, and best of all, no magic smoke was released during this video.
Nice job. I'm getting ready to install my FT-857D in my F-350 once the weather warms up. You guys gave me some ideas.
What a clean install! I would do my mobile setups that clean but i dont wanna tear out the insides of my tahoe cause i dont know how long they are gonna be setup in there for. You inspired me to get my ham liscence and i got my tech in January of this year. Ive been on the nets on my local repeater and am already in the process of putting up my own repeater!
2 minutes in and I'm like, "WTH is fish tape?" Hello Google my old friend. 😂
Having just bought a new (to me) 2021 F150, this could not have been better timing. Now to get my hands on an ICOM-705…
There is nothing like a good friend to have fun with
This video popped up at the right time! I was just looking at installing my radios into my Ram 1500 a few days ago.
Glad the word on Breedlove mounts is getting out! Running two; each side of the truck bed. HF and V/UHF.
Shane does nice work!
Hidden cables are a thing of beauty! Nice work! -Scott, KE4WMF
Great install. I have seen shane's work in person its amazing what he can do.
Now you need to bond and ground the engine, doors, tailgate, exhaust, cab, and bed. One inch wide ground straps as short as possible onto bare metal surfaces then covered with clear Krylon, non metallic paint to protect each joint. I've done tons of mobile HF, VHF, and UHF installs over my 30+ years as an Armature Radio Operator. You may be doing great in your driveway however, once you get on the road, you'll begin to notice engine noise and alternator whine. The board under the carpet is an old school method we used back in the 80's and 90's until the newer vehicles didn't have much grounding. You want to hard mount the radio to the floor board, especially in an all aluminum body. The more metal contact the radio body has, the better. You wont regret it. I installed an IC-7100 in my friends F-350 under the rear seat and I slit the carpet just enough to get the mounting bracket mounted to the bare floor board with locking nuts, washers, and bolts, not screws. It's a PITA to do however, the end results are superb. Good Luck OM and best 73's de N6JRZ.
There's no exhaust and I'm sure that the Lightning is properly grounded and electrically tied together from factory, especially with the 120V and 240V power outlets in the bed.
@@schnitznschnatzn How is there no exhaust? All vehicles have to expel burned fuel.
@@arbez7kit's electric
@@arbez7k, it is the F150 Lightning, a fully electric truck with 9kW of 120 / 240V outlets in the frunk and bed. Everything metallic on this vehicle has to be very well tied together electrically for safety reasons alone. Definitely no exhaust to be found here ;)
You're taking up most of your floor space with that.
It’s under the rear seats. Unlike the gas truck, I also have a front trunk and bed. I’m good. 🤘
I just bought a f150 last week and planning the exact same install.. could not have been better timing. I am using Breedlove mounts one ATAS and one vhf/uhf!!! 😊
I had a problem with noise on my tacoma, when driving, engine running and fuel pump emits noise. I cant hear anyone until i added FT 240-31 ferrite cores close to the ATAS 120A antenna, and also close to the the 891 radio and 1 to the DC line next to the radio. Now i enjoy listening to any band while driving. Yey!
At least it’s not the Cybertruck where EVERYTHING is a capacitive touch display or button. I’m still waiting to see how that goes. I have a DAC that’s all capacitive buttons, and it would go crazy every time I transmitted.
Robert KD4YDC here. Josh I love the Breedlove mounts. I have the one that is a bar where as you had to drill two holes in the front bed panel and then it "L 's" back toward the back of the bed (#313) then I also have the Stud Mount with a SO 239 (#207). That way when I hopefully add a Baby Tarheel, it will hold it. I can shake my whole truck when pulling on that mount. Not going anywhere. I do have some concerns about going through that vent. It is a flap type of vent that can introduce moisture into that area. I have seen that happen in other installs. For that reason, I just put some zip tie blocks on the truck and brought the coax in through the door bottom. Using Wireman RG58 coax.
I recognized Leah’s cough in the background at the 1:50 minute mark from the 2024 podcasts haha
I would not use Dawn as a lube, unless you thoroughly wash it off, they make special lube for cables, or you could use some water based personal lubricant. You know, some Kilo Yankee Jelly.
Shane normally doesn’t. He has pro stuff at work. I’m a scrub with Dawn. 😅
Can’t get much more water soluble than dish soap. Electricians wire pull lube is very messy stuff.
Soap lube - is this guy from boeing?
Now we need an install video on that ram mount post
Shane is AWESOME!
*rubs hands* been waiting for this. My F-150 needs an HF radio in it.
I've worked on my share of cruisers, so before he even said anything I was like, "this guys outfits cruisers..." 🤣 Great install!
Lmao. He does indeed!
Pro tip, stretch your electrical tape while applying. Squeeze tapping holds better than just relying on the sticky.
Also, never use soap for fishing wires, “soap” is slang for wire pulling jell but using real soap is silly…. Soap as it dries or gets thin actually grabs on like glue, that’s how it gets the germs off….
And it may work sometimes but it still bite you others, especially in conduit.
Laundry soap isn’t quite as sticky, I would use water based lotion in a pinch.
Nice install Josh, now clean that truck!!!
4:45 - pro tip - Dawn as a lubricant. As long as you are not Boeing!
Lmao. Yes
Nice install ideas, plus now I don't feel so bad about how dirty my floors are ;)
This is exactly what I did in my F150, but it's a 2019. Same path and channel to run the power to my D710
Shane did a great job!! Enjoy the HF!
Nice video. Great install.
I knew I recognized his call sign! I made contact with him on 20M on the 17th.
The key is to always have a bendy grabber for installs. I use mine waaaaay more than I thought, and i literally only install and take care of drunk people. 🤣🤙🏾
Nice work!!
Need to find a Vacuum cleaner lol.. You can get some L brackets to mount the radio down.. The setup looks good..
What did you wrap on the toroid, coax or power.. thanks for all the ideas, especially the board under the carpet. Only problem with that is snow in the winter.
Perhaps unrelated, but something to ponder:
Based on the lack of shops for repairing ham radios (and high labor costs), I’m questioning whether it’s wise for consumers to invest in expensive rigs. I own high-quality Icom gear from the late 90s. If and when they fail, I will turn to quality “budget” radios.
Found gas 2017 f150 has lots of ignition noise on 40 & 80. On 40 the noise blanker works on 857 good enough. Never has this issue on '03 Expedition. 80m is useless where my ARES nets are.
Good idea adding the toroid on the power cable. I wouldn’t assume the ground from the bed to the cab is good. Maybe add some braiding to bond the bed to the cab. I also added braiding to the exhaust system on my 2015 F250. Are you picking up ignition noise from the coil-on-plug system? A good NB will filter that. Have fun!
I would be very tempted to add some Ideal Noalox to that Breedlove mount where it comes in contact with the trucks bed stake. Aluminum oxidation stinks.
Ohhhh im going to do that.
I made the video as a ham alert. I'm good with it. :)
You did indeed!
Thanks for the video, Josh! I am preparing for my Mobile install. I am curious if you used a specific toroid. I know some of them have different mixtures. Also, did you use that gauge wire because that’s what you had on hand or is it best to use? I think 10 gauge that you had in the video? Last question that power junction box you had looked very well built. Do you happen to know the brand?
What were the steps to expose the grommet from the inside? What was the coax path to the grommet from the pocket? Where on the frame/chassis did you tie in the ground strap from the mount? Priority traffic from KC6ARY! 😂
In a 23 Ford F150 PowerBoost Hybrid. Have you noticed any noise on 40m,17m, or 10m? Thanks and 73
Still trying to find a good coax path in my PowerBoost from the stake pocket. This wasn't too instructive because they didn't show getting access to the grommet or the coax path to the grommet. I know it wasn't that kind of video but I'd love some clues from someone who has done it.
there are 2 pass through holes in the back area under the carpet. they are plastic plugs that can be drilled out. up front you can us the pass throughs that are used for the folding running board power.@@thecarys563
I know the brand of the antenna mount is Breed Love Mounts. What is the bracket and mount that you used?
Your web page links are not working correctly.
Great install. Board trick is the best. Let us know if noise levels change when driving. Thx
Oooooohhhhhh they changed! Stay tuned for whatever the hell I can do about that.
Curious to see how that noise level is when driving. My work truck (2019 Silverado 3500 Duramax) gives me an extra S2 the second you take it out of park. Definitely in the gear selector but I haven't had time to find and isolate it yet
I’m totally confused as to the routing of the coax from the rear of the bed to the cab. Can you elaborate a bit more? I’m trying to do this on my lightning
Both my Fords have put out a ton of pulse type rfi. I haven't been able to identify where it's coming from but it makes them almost unusable with the engine running.
I love your lightning. How bad is the RFI from the motor controller when you're driving? Btw, the ATAS is a great little antenna, however, you don't want to leave that bulky thing mounted while driving or at least tune it to 10 or 6m. It will otherwise self-destruct. I keep mine under the rear seat and just use a cheap Cameleon style antenna for most of the time with the FC-50 tuner. I think this works just as good or even better than the ATAS-120. I was talking to a bunch of DL and OE stations on 20m 2 weeks ago while driving down to South Carolina. Can't or at least shouldn't do that with the ATAS, definitely not on 40m. Ask me how I know :D
Also, I bet you could easily run a little 500W solid state amp off the power outlet for these "can you hear me now" POTA activations - LOL :D
Hey Josh, awesome install! do you leave the id-5100a head there all the time? Do you have any issue with sun fading on the lcd?
Are you disconnecting and putting away the head units when you park somewhere? That's one reason I haven't installed a radio in my car.
If Shane is doing mobile installs for steak dinners, send him my way!
Are you running with a direct connection to the 12V battery? That caused any issues?
For Teslas I've been told you shouldn't run directly off the 12v since the vehicle supposedly tries to account for all the energy in and out of the 12v to gauge its health.
Reason being if running the radio directly from the 12V the vehicle doesn't know about the radio using power and may think the 12V has failed since it will constantly be lower state of charge than the vehicle thinks it ought to be.
Was there any testing of SWR after installation?
Thanks for relating me to dish soap ;) Nice install and some great tips.
Hey Josh I just picked up a Wouxun KG-UV980P quad bander. Any Chance you can do a video about the radio/ 6m, 10m operations?
Alright, I have to take the plunge myself now. How is the Lido L-Max mount doing with both control heads on it?
Thanks for another great video!
WN8M
The L-Max is great. Very rigid!!
Question about a little detail. I see the speaker was mounted into the board under the carpet. Putting screws through the carpet, how did you avoid the screw grabbing a carpet thread a pulling a long length of carpet thread out?
Don’t sweat the small stuff? 🤷🏼♀️ I haven’t seen anything like that happen, so nothing to worry about.
Snagging carpet is a big deal in vehicle installs. You can make a tool for cutting carpet plugs out of a drill driver bit holder. Grind the end to an edge like a knife and chuck it up into your driver. Cuts prefect little round holes into any carpet or vinyl before driving any screws.
Rollie pollie habitat!
We’re hearing it live folks.
Curious how long did it take you to do the install?
Is there any particular reason you chose to mount the antenna on the Curb/Tree side of the vehicle? Any time you park in the street at the curb the antenna will be smacking the trees. Maybe not on your own street, but in general…
I agree. I always mounted my taller antennas on the driver's side to avoid trees if I parked against a curb.
Josh, was that Leah's new ride in the background?
Lots of frame grounding
Something is missing from under the bonnet/hood, the engine!
It’s got two motors. 🤣
is the ATAS able to handle the high speeds of highway driving well? I'd have to mount on my hood if I got one but i worry about 85mph on the interstate
It was mounted on my commuter car for four years before upgrading to the F-150 all high speeds. It’s been great. I don’t tune it under full speed though.
Noice.
What was the total install time from start to finish?
With Shane (the expert) and I together, just under four hours.
How’d you get the coax through the bed side?
It was on the pop-up. There are massive opening in front and behind the rear axel for the bed paths.
@@HamRadioCrashCourse Thanks! Giving me ideas. Got a WRC bumper mounted. Just got the ATAS yesterday.
What is going to happen when your kids spill liquid on the back seat and it drips down onto your radio?
I'll get new kids.
@6:56 Josh: What am I looking for?
Um, the wire.
Curious as to why you mounted the antenna on the right side of the truck vice the left side. I’ve always mounted.big HF on the left side. Generally there is more overhead height clearance towards the center of the road on the left side vice the right (curb) side to minimize the risk of bonking three branches and especially arched shaped underpasses. Lots of those here on the East coast, like in the Merit Parkway in CT and the Southern State parkway on Long Island NY.
On our 2012 Tacoma, the Icom 7100 main body is mounted under then under the driver seat and the power and antenna cables cone up through the floor through a slit cut in a large rubber plug in the floor pan and carpet above it. There are two such plugs one on the left side of the truck and one on the right side, perfect locations for running wires through. Avoids the hassle of running power through the firewall. The adjustable large cleats that run in the rails along the inside of the fender lit tops on Tacomas and Tundras can be drilled to take 3/8 z 24 antenna mounting hardware, you csn buy the cleats at Toyota dealers for relativey cheap money.
Curious on how bad the RFI from the electric drive system is In the Lightning, especially on the lower frequency HF 3:07 3:07 3:07 bands while underway.
73 de Chris AJ1G Stonington CT
Drive throughs.
Yes, good point, though many of them out here are more like a carport than a little overhang. Then you either take down the antenna or do the walk in thing.
Wish he could help me install an antenna on my van!
Shane needs to visit my QTH when I install a new mobile. Thanks for the video. 73 KF0NNQ.
You could feed 5 children for a week with what's wedged at the back of the rear passenger seat.
What?
@@HamRadioCrashCourse At the end of the video when you were showing the radio fitment. In between the seat back and the seat it looked like a carton of popcorn had been dumped there.
POTA MOBILE IS = POTABLE
Pretty hard to talk on a radio and push a ford isnt it?
To bad your truck isn’t white. You could have named it Moonshine.