Video není dostupné.
Omlouváme se.
How to Replace Front Strut Spring Assembly 2007-11 Honda CR-V
Vložit
- čas přidán 19. 08. 2024
- Buy Now!
New Strut & Spring Assembly from 1AAuto.com 1aau.to/ia/1ASS...
1A Auto shows you how to repair, install , fix, change or replace your front shocks with their loaded struts. This video is applicable to the 07, 08, 09, 10, 11 Honda CR-V.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oWM/1AX...
• 17mm Wrench 1aau.to/ojN/1AX...
• 18mm Wrench
• 12mm Socket 1aau.to/oMz/1AX...
• 17mm Socket 1aau.to/oMz/1AX...
• 19mm Socket 1aau.to/omn/1AX...
• 22mm Socket 1aau.to/obo/1AX...
• Trim Tool Set 1aau.to/ojQ/1AX...
• 1/2 Inch Breaker Bar 1aau.to/ohb/1AX...
• Ratchet 1aau.to/oXC/1AX...
• Socket Extensions 1aau.to/oMz/1AX...
• Torque Wrench 1aau.to/opr/1AX...
• Rust Penetrant
• Center Punch 1aau.to/obv/1AX...
• Floor Jack 1aau.to/onR/1AX...
• Hammer 1aau.to/ohx/1AX...
• Jack Stands 1aau.to/on2/1AX...
• Magnet - Extendable
• Wire Brush 1aau.to/ocW/1AX...
For More Info visit us at 1aau.to/h/aFD/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Critical mistake made in this video instruction. You must apply the load on the struts before torquing the bolts. Car weight needs to be on wheels or you need to Jack up the assembly. Loosely put the bolts on first then put the wheels on, torque the upper bolts to 33 lbs, then drive up a ramp jack, and tighten the two wheel strut nuts as tight as possible by hand, then jack the car up again, remove the wheels and torque those bolts to 116lbs. If you don’t torque with the loads on good chance you will hear noise while steering or settling of the springs / strut bearing May prematurely wear out
Thank you so much for making this video. Got mine done today. A side note for everyone:
When doing the top nuts on the driver side, you will need to remove the wiper arm... or do what I did and stop the wipers in the fill up position by turning the key off mid wiper sweep.
Thanks for the tip, it works great!
Your instructions were easy to follow. I successfully completed removing and installing new struts on my Honda and I bought struts from 1A Auto. Thanks
I purchased front and rear shock/struts from 1A Auto because they made this video and gave me the torque specs...... thanks!
+Alabama Woodsman Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@@1AAuto Sure! I just got done. The front was actually easier than the rear. I'd thought it'd be the reverse but being in the south, we don't have the rust issues as do ppl from the north.
The nut n grease tip is greatly appreciated!!!
Because of this video , I ordered the these parts of their store, they do a great job on communication and they ship mega fast from KS to Ca it took only two days wow they are amazing! Now I’m a a customer of their products, great job A1 auto
Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +jessie morales
Sir you did great job, Easy and fast way to replace the shocks. Thank you
THANK YOU 1A AUTO FOR THIS VIDEO BECAUSE OF YOU I SUCCESSFULLY REPLACED MY SUSPENSION/STRUTS ON MY HONDA CRV 👍👍👍👍👍👍👍👍👍👍👍👍👍👍I ESPECIALLY APPRECIATE THE TORQUE SPECS
Thank you for a professional presentation. First off, the screen showing the necessary tools. Stand out amongst a sea of inferior amateur efforts.
Great video keep up the good work .
Great job Andrew. I need my shocks done. Hopefully my hubby can get the job done.😃
If he can’t, I’ll come over and do it for ya. I’m sure you can provide a nice “service” for me as repayment ;)
@@spydersniiper you wildin 🤣
Thank you for this video. Excellent pace and very clear! I was recently told that I should consider replacing my struts. Can you briefly explain what to look for that would require having to replace the struts? Thank you.
10/10 video. everything was perfect. Thank you!!!
Torque : struts to wheel - 116 ft lbs
Sway bar link - 58 ft lbs
Top volts - 33 ft lbs
I like the way you "snug" everything.
Thanks for checking us out. 1aauto.com +Webster Chinyenze
Thank you! Very helpful.
I guess we know what happened to Toby Flenderson when The Office ended.
+Napoleon Dynamite Thanks for checking us out!
Great video thank you much!
Awesome man you did a great job thanks wish for you all the best
replaced mine about 6 months ago, recently developed that popping noise, replaced sway bar links, still had the noise. after checking all front end bolts, finally tightened the top five bolts again on the upper shock bolts. Noise is gone for now but the torque is way more than 35 lbs. Hoping this isnt a problem down the road.
If you live in the rust belt, its not a bad idea to have a set of sway bar end links on hand because the bolts may be so rusted you'll have cut them off. They can always be returned if you don't need to replace them.
+MacCready Thanks for the tip!
thank you for sharing this video and becoz of this.. I will order the parts from you guys.. for appreciation : )
+serafin molina Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
If my boot cover has fallen off but it rides well on my 2014 Honda CR-V. Should I replace the shock? If so do you have a video?
You forgot to film the tightening of the top bolts near the windshield wiper and the torque specs for those 5 bolts.
It’s the same torque value as the other side. 33 lbs
Looks like I’ll change the link at the same time if it’s that big a pain to loosen.
Fantastic video made it look so easy
+Robert L Thanks for checking us out! 1AAuto.com
I've never replaced struts before and this video was enough to get it done. I purchased the TRQ Brand off of Amazon but they seem the same as the ones in this video.
Why not order them from 1A and support the company actually making these videos
Wiper hose replacement video please. Thank you :)
I have been watching a few of those CRV videos. Great videos! Is there a reason you don't use anti-seize compound on any of the bolts during re-assembly?
I agree and show entire video, you know he replaced the sway bar link as its new one, be nice to see best way to take off bottom because no need to take off Strut if junk, and he should of stated most don't like coming off, when seen hammer banging on 6mm to take sway bar, I knew it was getting replaced. It's worth the headache and ride quality to know it's NEW and can be trusted.
@1AAuto: How do you know when you need to replace the front strut spring assembly for the 2007-11 3rd Gen Honda CR-V? Thanks!
Is an alignment needed after this
Thanks very much
For anyone looking to buy a new complete strut set. DO NOT BUY KYB!!! KYB top strut mounts do not set in place properly and will make a ton of noise almost immediately after install, they will get worse over time, and will throw off your alignment over and over again. The strut/shock itself is great, but the top mount is not. KYB will not address this common problem (check the crv forums) and will only send you the exact same strut back to you which will do the same thing as before. OEM complete sets are more expensive, but will work like they are supposed to. If you are just replacing the strut with kyb, but keeping the oem strut spring and mounts, that will work great as well. Good luck!
Hi. Could you please give me the code of front shocks Honda CR-V model 2006_2007?
RGDS
The rear is the hard ones!
Fronts are always easy!
Lol, the links were all cut on mine. All the same bolts were seized.
I see you used a 17mm and 3/4 socket for the sway bar link nut. I can't get the 17mm to fit. So what is the best/correct size?
Update..a 3/4 socket on an impact driver and vise-grips on the back worked great
Great....💯💯💯👍👍👍
I from Perú , have a honda CR V 2007
Hey there, I am having trouble lining up the strut with the wheel housing, the cv joint doesn't allow me to move the housing into the strut. any ideas?
Would this be the same for a honda hrv??
I find that there are purchase links that repeat the products, does anyone have a link that is necessary to buy
A1 AUTO SELLS THE REPLACEMENT STRUTS SET WITH SWAY BARS...BUT I DON'T SEE YOU REPLACING THEM ERE. ARE THEY NEEDED? RECOMMENDED?
they are in a separate video. if you search on Youbube, there you will find it
What's the name of the tool holding the brake rotor
Should I get the wheel alignment before or after the install?
+Andrew Ramos You should do this after the install. Thanks for watching.
@@1AAuto thank you.
+Andrew Ramos Yes, we do recommend having the alignment done after installment. Thanks for checking us out!
How do you know when your struts has to be done
Do you guys have a Canadian Distributor equivalent? Looking to DIY in Alberta
+Owen Fisher We do not have a supplier in Canada at this time. Thank you for checking us out!
Geez, why not replace the sway bar stabilizer links at the same time? Get Moog, with grease zerks..... and no 6mm hex needed!
Are the shocks absorbers alredy inside the struct assembly??
+Aaron Gregory Yes. Thanks for checking us out!
How can you tell if it’s the strut?
13:15 What?! , no Anti-seize? Honda has terrible engineers that designed that nut/bolt setup! All after-market sway links have regular nuts, and a mock nut at the back to hold it from turning (right where you put the vise grips). Thanks for this video though,,,awesome!
+CenterTree777 Thanks for checking us out! 1AAuto.com
Another critical mistake, always take out axle nut. Don’t want to pop a axle and end up replacing one.
Why not show entire video on how to replace the sway bar link and how you got it off the bottom, you never show how to do the entire job, some don't know and maybe shouldn't be doing it but it's what they must do because of money, so if making videos on how to and where to buy, then show it all because that's a new sway bar link, a person needs to know if they should replace them or not if they must be cut off, these are the worst designs ever by all manufacturers PERIOD. Thanks on saying that don't drop lower control arm or can cause damage to CV JOINT, then some don't know what's a bad joint, when you hear clicking going around corners from front, most likely a bad Joint, replacing your strut, good time to replace that as well as its 1/2 apart already and part isn't much, last I knew, about $70 to $110 depending on where, can buy remanufacted parts that's cheaper and people believe new is better, not always true, had more new parts fail than remanufacted parts. So always return those CORE CHARGES and get your money back so it can be rebuilt. Most of the time on these sway bar links, they don't like coming off, I knew when hammered on socket 6mm Allen head that it wasn't coming off easy, these cost about $15 to $50 depending on vehicle this one is higher priced because it's bigger as in long and many are like this, replace it so you don't get the clanking noises from bumps and handles corners much better when new and if must take one side off, then take other off and put new, should last a long time if done right. Also 19mm on wheel lug nuts, mine are 17 mm and on the locks as well. Once I replaced a part that was rebuilt and was Dealership item only, bought at local junkyard for $25 plus $2 insurance on it, got credit because junk, hard to get part off and back on, was for a different vehicle and Dealership price was $1,100 online through a place like this, just $125 remanufacted parts with 1 year warranty, cost me $5 to ship back to get my $25 CORE CHARGE back, so return them so they can be rebuilt, reman parts can be better than new, I once bought only new, now I'll take Renan over New, less chance of failure, these places do a great job rebuilding them and testing them and better than new on certain parts. Many years ago, you had to get rebuild kits to fix vehicle, these stores wasn't around then, either junkyard or rebuild parts, it's how I was trained on brakes in High School Shop Class. Much cheaper to do at that time. If didn't rebuild brakes right, then you couldn't bring in your vehicle to work on it and failed a grade on not rebuilding caliper or wheel cyclinder (drum brake), cost like $3 on kit but best do it correctly or will leak on you, your brakes us your life and everyone out on the streets and sidewalks, so your responsibility is high if rebuilding them. Please when making a video, just show it all that's done because I knew right away it's a new sway bar link, it's money you will make as if never been replaced should be if replacing Struts now. It should be mentioned that this should be replaced unless replaced recently and comes off easy, most don't that's made like these, and should explain what's what because shops will sell you just Struts and not the Strut Bearing on top of Strut that always should be replaced, my noise never went away on old vehicle and Shop said your Struts are fine at 160K, he was right then started blowing out with there junk ones but never put new bearings on, came back and said the noise is still there. They honored Struts 3 times as leaking in 15K and said no more, lifetime was lifetime, then filed chapter 13 and many uses there tools as almost as good as other ones you see at many garages. Then told me that's the Bearing making that noise, said I should of been told this as I bought my tires here and other stuff. Best to get loaded Struts for safety for one thing like he stated don't remove nut, that spring will kill you, I got tools on old vehicle and put new Strut Bearing on, was good then got notice that Strut towers become loose over years and have new one welded on over old from it. No recalls, only a service bulletin and then they didn't do recalls on some stuff yet. Then it started when people getting killed. Mine was off road with 196K on it but ran like new, never leaked or burned oil. Parked 12 years ago out back. 1st new car bought ever. Brother-inlaw replaced my starter and broke ear off from over tighten it, I got another from cousin who was the manager but had to wait the next morning, he not a mechanic and 6 years later my starter started to drain my battery. Was new.
hi, does honda crv's shock breaker can fit into honda fit? ty
+Arrahmansah Tetra Typically you would need to search using the complete year, make and model. Sometimes the shock absorbers do work for different models.
On your site, what is the difference between the strut Part #: 1ASTS01087 and Part #: 1ASTS01086 ? For 2011 CRV. I need the driver's side.
gas type or hydraulic?
+jeric lee Thanks for watching! These are gas charged shocks.
New nuts lol oh please don’t judge me
My used 08 crv front suspension is way higher than the back suspension...back has like 2"gap
Front has like 5" gap. .
Did someone put a spacer possibly?
Get the wrong one's that has a lift to them, before putting parts in, always match up, yes old will be shorter but not by much if any, 5 inches would of been noticed if put side by side. I'm sure it was figured out by now.
Baieti mea disparut treapta in urma carei cauza
How much does the strut cost?
Hello, for the 2009 Honda CR-V, The Front Strut Pair is currently listed at $64.95. We also carry the Front Strut and Spring Assembly pair, currently listed at $189.95. +gaming vampire aby
Dont buy honda. You will wast your money. When assembling they use low Quality chinese parts. Before
First 50000km you have to replace all suspension parts.
Why don’t u use any power tools ??
Watch again. He did when needed.
I think because if talking while filming video to do for CZcams and we all could hear him well. That I was happy about and heard everything said. I just wondering why he didn't use never seize on nuts putting back together and stated that he replaced the Sway Bar links as its best to unless already done. If original, then replace them with Struts and worth the extra money if paying someone or doing yourself, then only need to take bottom nut off and leave it connected to Strut as don't need. Will be happy because in a few months, you'll hear a noise and think Struts you did an have checked out only to find out its the sway Bay links is bad on one side. They break when you don't want them to, when trying, can't break them off. Stud just spins which sucks. Replace with Struts, it's one thing a mechanic won't lie to you about, if any, they may say there fine so you go on with noise and they just missed there bad day of taking off. Some are a pain to replace.
Torque dem nuts
Updated video to replace this old video: czcams.com/video/xciDzUc-LRw/video.html better "tips"!!!!
Hey A1 remove the old video!!
Cheap strut wont align do not buy