Just What Is Up With All My Personal Projects And Motorized Bicycle Builds!
Vložit
- čas přidán 11. 06. 2022
- Well been working on tons stuff for the other my other channel lately! That time of year again! Motorized bicycle have been taking off in are area in mass numbers it seems! Trying to get this ms460 kit off the ground and opening up a whole online shop at the same time! Been riding the 4 stroke around mostly till ms460 got rebuilt! Everything ahs been crazy with warmer weather here and bikes keep showing up to be fixed!
Starting to see lots of people now riding this around since gas is crazy priced these days! Anyhow stay safe and watch out for cars! seen two people in Sc lately 48 hours wreck bad! 2 get hit by cars! Remember most people are not paying attention! so don't expect them to see you! Orange Vest seems to be just invit to run you over these days so be proactive and ride smart, Cause chances are the crazy Karen with cell phone is not!
#bikelife
#bikelover
#diy - Auta a dopravní prostředky
Good to have reserved power when you need them 😃! As always, your vids are great source of info esp for DIYers (saves some $$ than buying ready-made 😁). As a hobby, it's self satisfying when your re-building something to make it run better! Awesome build! Thanks!
Thanks! 🍺😮👍
Gonna have to get the bbf decals made up for the clutch and magneto covers. Some of us old school guys are still 100% sure that stickers/decals are good for hp/mph gains. Especially if the kits take off the way it’s looking like they will.
Lol 🍺😁👍
Good-looking windows. I like to round off the sharp edges on the skirts to avoid hot spots and "cold" seizures. Less turbulence too.
Yeah I hit all the edges with fine nail file normally before I toss it in!
Dont feel bad! Your builds are great! I just spent a month in hospital from a fall off my minarelli with no helmet….learned lesson and never again but it’s def made me re evaluate some stuff!
I always wear a helmet. Tell yeah. I watched a guy smack his head on a rock once wiping out. It cracked his helmet and I am 100% sure he be dead. He was stunned but walked away. After that I never questioned it lol
@@BuildBreakFix yeah never again without a helmet man.. I am lucky to be replying to this now.
The new piston looks very similar to what we did to the 80cc karts,, two were found optimal for us
52mm piston? I think its 98.7cc saw. 86cc was 50mm and ms660 54mm 102cc 56mm I think 118? something like that!
@@BuildBreakFix They are short stroke though aren't they? 52x52x38x0.785 is 80cc approx.
@@matouslitera8073 your correct! Dono wtf I'm saying there lol. 52mm @ 38mm stroke is 76.8cc and the 40mm stroke is 78.4. I thick I was talking about the piaggio. Lol tired😁👍
Phantoms aren't bad if you correct all the issues. I used a MS380 piston, sae660 bushing, g2 reed with tm24 mikuni, & decent expansion pipe. I bought 1 from the very 1st run, before the problems were known. They do work, just not outta the box
Some of gen 3s are such bad castings. Phantom was a grand idea. Just poorly thought out
I Enjoy your videos 😎
Ha thanks! 🍺😉👍
you like working on the motors more than riding them Best adult erector set you can get Never change your video format man your videos give me some good ideas
Lol thanks! Honestly though enjoy building them more then riding them.. must of fix 12 bikes this week 3 where so bad even surprised hell out of me they ran lol
I new you'd figure something out that window piston looks sweet keep them videos coming
Yeah first one I did was just error on my part. Never really looked into piston windows on that type. Found out after I made it it would tank! Live learn lol! Ms460 are being tortured trying to make at the min. Trying to make sure nothing fails! This is a ground up project! Looking good so far though!
@@BuildBreakFix have a great question for you how can you tell if your main crank bearings are going out any assistance would be greatly appreciated
I just battled my new lawn mower issue. But all in all after all the issue the carb floater has a hole that caused it not to work I still plan on building a motor bike. Just house has more priority now.
Dry out the float! Put a dab of gas tank in weld on hole!
@@BuildBreakFix I got a new carb for it. Now it runs great. …and I did that but I saw a hole in it. Little gas got in maybe just a faulty floater. I’ll grab one for it to have as extra
I tried to use a ms440 in my yd100 and it had great top end but it had an intermittent miss at midrange, like a bad one. O well
They say it's really common with ms440 and the ms380, they say it has something to do with port design? Don't really know first had! Seen others say that on forums
MPH has everything to do with gearing and much less to do with what cylinder it is
well depends on porting of the cylinder ! If you have low range porting you will never hit past 6k rpm. Minarelli is like mid port 10k rpm range (without serous mods or stage 6 jug) and the saw builds are made for 75% porting scream at 14k rpm. so if your porting matching the sprocket of what that engine can drive at higher rpms plays huge roll in speed! fo example I ran a minarelli on a 22T sprocket still only hit 70mph! Can do the same thing on a 32T sprocket. Minarelli just didn't have the balls to pull that 22t! On other hand saw build can't even get up to 50mph on it! but can fly easy one 32t past 65!
I had a kind of stupid idea do you think it would work if you use the port for the pressure release valve and stick an injector in there a wet nitrous system. I know it’s a pressure release valve but it seems like you could do so much more with it fuel injected would be nice
Sure just need the 100$ fuel injector, oil mix regulator 300$, efi controller about 400$ o2 sensor another 80$, fuel pump 75$, oil storage tank $??, and fuel injector throttle body, 150$ lol. Seriously! I actually have a efi ktm 65 go kart! Those are the serious parts prices lol. All small engine efi is so much $$$ and bloody hell to setup.
Yeah you definitely don’t need a huge window for a window in fact you’ll get a little more to work with a smaller window
Yes! Actually did improve it running! Smaller window was big change!
@@BuildBreakFix
The mushroom shaved exhaust port that starts closing at transfer line or above it if you have enough duration that helps a lot as far as tuning in How it rides especially with reed valves will make it more efficient the arch of course helps determine speed or torque and angle of transfer exit helps determine this as well I’m sure you know this already
imagine a left handed derailier, so we could run gears, just imagine how useful that would be.
Well that was the idea behind the shift kits. Sadly the derailleurs tend to fold up and rip every spoke out of the tire at some point 101% of the time lol sthus Black Shifter Kit Jackshaft Kit Fits Regular 415 Chain 66cc 80cc Gas 2 Stroke Motorized Bike Bicycle a.co/d/8Z7kjFI
@All About Bikes there is two companies that make pit bike transmission hubs. Seen a crazy build with one on a bicycle but was no more impressive then motorized bicycle
Hey brother soMethiNg else that would help with cooling besides a ceramic head would be running a single ring piston and doing a lateral piston port )to cool rings look it up you’ll see what I’m saying it’ll help cool the rings and all and keep from seizing just don’t get the bottom side of ring groove only works with a single ring piston maybe if ya remove the second ring it may idk also their is gas ported rings tho that looks 🤷🏻♂️ anything is worth trying and if ya fail ya learn WHY ya fail and then fix it till it’s perfect!
What? Ceramic cylinders run hotter though not cooler. Ceramic coating on the outside of the cylinder is to deflect heat away from stuff around it. This saw build wont have a cold seizure issue. Both the piston and jug are aluminum. Did you mean ceramic topped piston? Defects heat off the piston like I did in my minarelli?
I am really looking foward to build mine to ms460 jug but not flapper just piston port
Hostly I drove one of the 460 bikes non reed. The thing has so much balls without one you wouldn't really need one!
@@BuildBreakFix Thanks for all the knowledge 🙌
On your pz20 did you drill the pilot jet because i can't find any pilots for those anywhere
My pz20 carb actually came with tons of jets! I know it's like finding fresh unicorn meat these days! I wish I bought more of those when I did a year ago now!
@@BuildBreakFix lmao fresh unicorn meat . Maybe road kill moose. Lol
Are windowed pistons only effective with a reede valves
lol?
Just wondering how one would affect my stock yd100 if I got one of the pistons you got in this video
I think you have a video explaining the yd100 upgrades so I'll just go watch it and see what all you say in it
@@cliffbradford4679 ? Oh you think that is a kit piston? No that ones goes in my personal build. It's a g2reed build. All honesty zero top end changes. But it for sure gets more out of the gate windowed.
@@cliffbradford4679 window in piston would give yd100 alot more balls out of the gate. Little bit more Top range in its power band. I love yd100 builds must done 20 different ones now. Yeah reed for sure gives yd100 more bang for the buck!
Also it’s ok if ya quote me even if ya fuck it up but yeah lateral piston port to cool rings or gas ported rings could be something to look at for ideas
Interesting! so removed the ring to cut a port next to it? Still runs? I did that with yd100 build but I just moved the pin to other side little off from ring above!
@@BuildBreakFix here is a good example
czcams.com/video/nZshtk0nQNY/video.html
@@BuildBreakFix also this side gap porting
czcams.com/video/M7PfIQN9QzU/video.html
Can I have that super saw build you made it looks so fucking awesome the white color with the orange sawzilla build I want it please
Lol I made like 60 of those was selling them! Haven't been making any lately with all the crazy stuff going on. Was creativecncshop.com. But temporarily closed it for now