How to Remove & Replace a Gimbal Bering on a MerCruiser Bravo III
Vložit
- čas přidán 3. 05. 2023
- How to Remove & Replace a Gimbal Bering on a MerCruiser Bravo III
/ uciv1n5fsmrryk3hogdu1nhg / onboardwitheddie
/ onboard_with_eddie
When available, we use affiliate links and may earn a commission
Links to products in Amazon
MERCRUISER PARTS
Hinge Pin Tool Compatible with Mercruiser Mercury Alpha 1 Gen 2 Bravo I II & III Outdrive Sterndrive amzn.to/3uD0CUl
VOWAGH Bellow Retainer Ring Install Driver Tool Compatible with Mercruiser Alpha One Gen Two Bravo Replace Mercruiser 91-818162 Sierra 18-9870
amzn.to/47YaaHF
Gimbal Bearing Puller/Remover & Bearing Installer & Alignment Tool fit for Mercruiser Alpha Alpha 1 MR Bravo OMC and Volvo
amzn.to/3sVuZVp
Manifold Engine Block Drain Plug Kit Replaces Sierra 18-4226 for Mercruiser 22-806608a02 Compatible with GLM 13992 Pack of 5
amzn.to/3QVUT3o
Fuel Filter and Filtering Disk Set 35-8M0093688 866171A1 8M0093688 35-892665 for Mercury Marine Mercruiser Engines with Gen III 3 Fuel Cooler
amzn.to/47Xlhka
V8 Distributor Cap and Rotor kit for Mercruiser and Volvo Penta 5.0, 5.7, 6.2 Engines, 350 MAG MPI 5.0 5.7 GXI GI
amzn.to/3t1uBop
863631T1 Water Distribution Housing Assy Distributor with Drain Plug for Mercury for Mercruiser for Quicksilver
amzn.to/3NdCRZx
RPS-GLM Bell Housing Gimbal Water Hose Tool, Driver Insert kit for Mercruiser Bravo Drives Replaces 91-43579 &
amzn.to/4aaxRhV
RPS MERCRUISER Water Pump Rebuild KIT Impeller Cover O-Ring 496 8.2L 5.7 5.0 4.3 350
amzn.to/3uMyPRz
Bearing Retainer Install and Remove Tool for Bravo III Replaces 91-8053741 805374-1 Bearing Retainer Wrench
amzn.to/3TbY1e3
I've learned a lot from your videos over the years.
Always happy to help out. Thank you for all your support throughout the years.⚓️🤙
Me too! Thank you.
Thanks for making this video. I needed to see these tools in action and figure out where to put that hole in the installation tool.
Eddie you gotta show us how you do bellows replacement. Lots of videos on CZcams about it but they all tell half of the story.thanks again for another great video.
I already have that video done. I just have to edit it. That’s the next video 🤙⚓️. Just have to get the time to edit it now. Lol
Hey @onboardwitheddie another request for a bellows video! I’ll be doing it this spring on my B3
Year after year i return to watch your videos. Thanks Eddie! I must say that this particular job looks like a pain in the ass!
I hope the videos help you out. It’s not really that bad of a job. once the outdrives are off. just takes a little muscle. thank you for all your support. 🤙⚓️
Great videos. Thanks so much !!. Just recently bought a boat with the 5.0 mpi. I will definitely be referencing your videos. Best I've found.
Happy to be able to help you out. Thank you so much for your support.🤙⚓️
Thank you, my brother, for this distinguished work. Thank you very much and more than that❤❤❤❤❤
Happy to help out thank you for your support🤙⚓️
Happy to help out thank you for your support once again🤙⚓️
I would love an video overview showing what are typical items that we should be looking out for as preventive maintenance and when (run hrs) to do these. Also maybe general maintenance schedules such as drive oil change out time frames and sea water impeller and such.
You can use your grease gun to push some grease thru the hole on the gimbal housing to aid in lining up the grease hole on the new gimbal bearing on the non-sealed gimbal bearings when applicable.
If the shaft is stuck in the bearing and the out drive is not coming ouy/off What do you suggest or do you have a video for that ?
Hi Eddie, good to see you on the screen again. How often do we need to replace the bearing? Does it start to make sounds when it is on its way out?
yes it does. It will make a winding noise. once in a while a clicking. Thanks for watching the videos and thanks for your support. 🤙⚓️
Thanks Eddie.....!!!!
Liked. Stop showing off your guns bro 💪 lol
Great video
Thank you for your support🤙⚓️
The universal tool you used to hammer the bearing back in, wouldn't that only be a safe way to set it up assuming the old bearing was riding where it should be?
Is it possible to hammer the bearing in too far or is there a lip in the housing to stop it where it should be?
There’s a lip where the bearing will stop
You put bearing in wrong. Little dot on bearing should be at 10 o'clock position.
I will stay with outboards