How to Replace Rear Brake Rotor Backing Plate 1999-07 Chevy Silverado

Buy Now!
New Brake Rotor Backing Plate from 1AAuto.com 1aau.to/ia/1ABM...
The brake rotor backing plate protects the inner brake rotor and brake assembly from road debris, dust and water, to keep your brakes stopping effectively and safely. If the backing plate on your vehicle is broken, bent, or missing, braking safety could be affected. This video shows you how to install a new rear brake backing plate on your 1999-2007 Chevy Silverado.
• Check here for more videos on the 1999-2007 Chevy Silverado: • Chevy Silverado 1999-2...
This process should be similar on the following vehicles:
1999 Chevrolet Silverado 1500
2000 Chevrolet Silverado 1500
2001 Chevrolet Silverado 1500
2002 Chevrolet Silverado 1500
2003 Chevrolet Silverado 1500
2004 Chevrolet Silverado 1500
2005 Chevrolet Silverado 1500
2006 Chevrolet Silverado 1500
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 18mm Wrench
• 13mm Socket 1aau.to/oa/1AXA...
• 18mm Socket 1aau.to/oa/1AXA...
• 8mm Socket 1aau.to/oa/1AXA...
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• 3/8 Inch Socket 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Socket Driver
• Socket Extensions 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Brake Grease
• Brake Parts Cleaner
• Gear Oil
• Liquid Thread Locker
• Paper Towels 1aau.to/oa/1AXS...
• RTV
• Rust Penetrant
• Drain Pan 1aau.to/oa/1AXA...
• Floor Jack 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
• Jack Stands 1aau.to/oa/1AXA...
• Razor Blade / Gasket Scraper 1aau.to/oa/1AXA...
• Wheel Chocks
• Wire Brush 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Chevy Silverado 1999-2007 1st Gen: • Chevy Silverado 1999-2...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*

[@shadowopsairman1583]

Those are single piston calipers, the plate you are using is it the same for the dual piston caliper? What about the 9.5" 14 bolt rear end?

[@lilskittelz8514]

You don't have to remove the axle to put the dust shield on its a two piece design so you don't have to take the axle out saves a ton of time

[@aaroncalhoun9825]

WHYYY would you show and obscure and specific use tool in a video and not give any clue what it's called and where we could buy one? It's not in your tool list... nothing.

[@187Rossi]

What would a reasonable price be for this service at a decent shop??

[@stevenaugust8819]

Appreciate the video dude

[@MrJ6789]

do you have a video of removing wheel cylinders due to bad bleeders both side of the rear drum on a 2006 Silverado 1500,5.3Litet 4x4 extended cab.
If I need to replace the dust shield and remove the axle do you have a video on that as well.
thank

[@MrJ6789]

bleeder bolts are rusted really bad and i can't remove.

[@mattunger4554]

Do we need to top off the diff fluid after axle gets pulled? Or is the volume not enough to worry about?

[@shadowopsairman1583]

Those are single piston calipers, the plate you are using is it the same for the dual piston caliper? What about the 9.5" 14 bolt rear end?

[@terryobrien4644]

Very helpfull thank you!

[@bkee62]

Nice work but way too much extra work. Use the two-piece part from Dorman. I think it's 924-213 and/or 924-222. The first number is 1 side, the second part number is for both. It does get a little confusing there are two pieces for one side. So if you're doing both there will be a total of pieces.

[@alexanderdashkov4350]

Very helpful, trying to find specs you have and it's a cluster fuck. Are you getting yours from ALLDATA?

[@tonynavarrete5937]

What about the cover for the other side?

[@TRQ]

+TONY NAVARRETE The installation process for the other side should be very similar.

[@uberdome1]

Its not an emergency brake, it a parking brake!