In this 4g64 engine you MUST balance the oil pump sprocket correctly; unlike other engines, it is not enough to make the marks align, there's a process to check if the balancer is in place of is 360º off (a full turn) this is what would make the enngine vibrate if not done correctly. The manual shows the correct way to do it, there's a service bolt on the driver's side of the block you stick a screwdriver in to check if the oil pump balancer is facing the correct side
This is a 4G64 engine. One way you can check if there's any valve or piston damage is by doing a leak down test. Remove the intake and exhaust valve rockers first, this will ensure that all of the valves are closed and you can do the leak down test safely
You forgot to show how to properly tension the timing belt. Should be after 8:45 and before 8:46. There is an actual process to this. Just throwing the hydraulic tensioner and eccentric pulley on is a guaranteed future valve job. Yes it is an interference engine unless you are lucky. Done many of these engines in a dealership back in the 2000’s. Even had one fellow tech spray some brake cleaner on the belt while running, trying to find an oil leak on the oil pump just to watch the belt fly off. Had to send a freshly rebuilt head back to the machine shop to get valves replaced for a 2nd time.
Vendo um 2.0 Super Saloon 1998, não é o V6. Todo original, ainda com som toca fitas, conservadíssimo. Todo original, exceto as rodas que são de competição 17". Tudo funcionando! R$ 18.990
hello a question to me the crankshaft is broken ... something happens to the pistons .. when the valves do not lower or affect him, px burst only the band changes ..
hi damon i was talkin for those( sohc ) not ( dohc) honda civic n mitsubishi sohc 90 % if timing belt go bad i am sure not cause damage hoo 1 thing important do not open the plastic cover and turn the cam if u do dont crank engine intill install new belt cuz valve are at hide point anyway the car u see i paid $50 dls they said same thing bent valves 100% not pass smog with good numbers
Some people delete the balance shaft. The engine wont idle as smooth without it. Some do that because if the balance belt snaps it can cut the timing belt and the engine gets damaged. The balance shaft belt pulley rotates at twice the speed of the crankshaft. Normally it fails, the balance belt snaps and then the timing belt snaps.
In this 4g64 engine you MUST balance the oil pump sprocket correctly; unlike other engines, it is not enough to make the marks align, there's a process to check if the balancer is in place of is 360º off (a full turn) this is what would make the enngine vibrate if not done correctly. The manual shows the correct way to do it, there's a service bolt on the driver's side of the block you stick a screwdriver in to check if the oil pump balancer is facing the correct side
This is a 4G64 engine. One way you can check if there's any valve or piston damage is by doing a leak down test. Remove the intake and exhaust valve rockers first, this will ensure that all of the valves are closed and you can do the leak down test safely
You forgot to show how to properly tension the timing belt. Should be after 8:45 and before 8:46. There is an actual process to this. Just throwing the hydraulic tensioner and eccentric pulley on is a guaranteed future valve job. Yes it is an interference engine unless you are lucky. Done many of these engines in a dealership back in the 2000’s. Even had one fellow tech spray some brake cleaner on the belt while running, trying to find an oil leak on the oil pump just to watch the belt fly off. Had to send a freshly rebuilt head back to the machine shop to get valves replaced for a 2nd time.
Ok so was my lucky day
Tenks man..... welcome tô Brasil , mestre
Saludos amigo
Vendo um 2.0 Super Saloon 1998, não é o V6.
Todo original, ainda com som toca fitas, conservadíssimo. Todo original, exceto as rodas que são de competição 17". Tudo funcionando!
R$ 18.990
How did you get crank pulley it keeps hit the frame and won't come out
well you dont show how you did the actual set up of the tensioners,engine also sounds rough do you have check engine lite for cam or crank sensor?
FYI this motor 4G69 is a interference motor. You got very lucky that the valves was not bent.
Corey Raines 4g64*
hello a question to me the crankshaft is broken ... something happens to the pistons .. when the valves do not lower or affect him, px burst only the band changes ..
How do you get the screwdriver out if drop it into hole to check oil pump timing
On the 01 eclipse 2.4
my crankshaft bolt isn't coming off as easily as you show..... not even close. I've tried everything it isn't moving on my car at all
How long did this take?
No to long 2hrs maybe
sete olvido balanciar la ponpa del haceite hora tiembla mucho o no el mio le paso lo mismo y tube que valanciar la de ponpa aceite
Nice
Do you have to remove the timing components to remove the crank shaft sensor? Error Code PO335. Thanks!
hey james u have to remove just the cover n its aesy to get there look on min 11:00 any question let me know
Cool..this code started poping up this week and it is my kid's commuter.. I'll take a look! Thanks Julian!
thanks any time where here happy july 4th
The Galant doesn't seem ok dude. I mean I don't wish that on you but that engine doesn't sound right
thanks for posting, but not sure why you wouldn't think the valves wouldn't get bent. It's a interference engine unlike most Honda's
hi damon i was talkin for those( sohc ) not ( dohc) honda civic n mitsubishi sohc 90 % if timing belt go bad i am sure not cause damage hoo 1 thing important do not open the plastic cover and turn the cam if u do dont crank engine intill install new belt cuz valve are at hide point anyway the car u see i paid $50 dls they said same thing bent valves 100% not pass smog with good numbers
julian #1automecanic Ok, I see what you are saying Julian. Thank you.
damon323 hey thanks man stay tune i am going to pick up mitsubishi mirage tomorrow look like same problem I will record all that to confirm 100%
What bout if the timing is off
if timing its off ur car its not run ok and probable bent valves
I need help with my crank shaft sensor how I get it replace !?
good to know, yes important to note SOHC 2.4.
Hey tanks man 👍👍👍
My Mity mas don't have the short belt behind the timing belt it doesn't have the gear or tensioner 2 4 engine
Some people delete the balance shaft. The engine wont idle as smooth without it. Some do that because if the balance belt snaps it can cut the timing belt and the engine gets damaged. The balance shaft belt pulley rotates at twice the speed of the crankshaft. Normally it fails, the balance belt snaps and then the timing belt snaps.