How to measure Thiele Small Parameters using your Sound Card
Vložit
- čas přidán 6. 01. 2024
- How to measure the Thiele Small parameters using your sound card and Room EQ Wizard.
If you want to learn about DIY Audio : audiojudgement.com/courses.html
If you want to build the measurement jigs: audiojudgement.com/measure-th...
Music Credits:
"Werq" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 4.0 License
creativecommons.org/licenses/b... - Zábava
I prefer to just hold the driver in the air with one hand, away from any surface, which can affect Fs and as a result everything else. If it's a large driver, I use a small rope threaded through its mounting holes to suspend it from a step ladder or chair.
WoW ! Just what I was looking for !
I'm glad, that i purchased the DATS V3😅😅
Salutari si la multi ani!, ar fi foarte fain sa faci versiuni ale acestor videoclipuri si in limba romana, Marius, cred ca s-ar uita multa lume.
Sd can also be calculated from cone diameter right in REW itself, in the TSP menu where you enter the values. There should be a small calculator icon.
Dayton Audio DATS V3 is well worth the investment.
Amazing and such a timely tutorial on this , especially if the local indian brands are either not providing complete parameters or none at all
TS params -> winISD -> box-design for low low freq sound - (trying iso-baric for smaller box)
Nice video! A mixed option is to use REW & dats hardware. Allowing a better configuration (sweep duration, level) and the posibility to use the dual mass method ;)
Thank you.
This is so cool that I just have build one, even though I don't have an immediate need. 😂 I already have all the parts on hand, and 1% tolerance resistors.
I like the Dayton reference paper woofer
Thanks 🙏
Obrigado Mario 👍🏻
I can use the line in of the sound card instead the microphone input? These are always stereo
Tried hard but all I saw was USB sound cards with mono microphone jacks.
Do you have links/suggestions, please?
Would it be helpful to add a resistor between the mic and the one output wire?
How to know Le of voice coil?
Hi! thanks for your Videos and tutorials. I have a 'rookie' question, not directly linked with T/S parameters mesurement. For the calibration of the internal sound card of a computer(desktop or lapto) in REW is it compulsory to do the calibration in short circuit (i.e in loop if I understood correctly) ? Could it be done with a Trrs cable ? I'm planning to begin with simple mesurements with a DA IMM6 on a computer.
Thanks 😀
Can we use this to test small headphone drivers? I t does need different rezistors?
Hello! Great video! Interested in Xmax measurements! Maximum Displacement! how to measure it! After all, this is an important parameter, and in some sports data it is missing!?
For Xmax you technically need to disassemble the speaker. You need to know the voice coil height and gap height. Xmax is the [(voice coil height) - (gap height)] / 2. This is the Xmax one way for an overhung motor.
Hi, I was trying to replicate all step by step and it fail to show up in windows sound panel. Now I have checked all wats wrong , and apearantley - on schematics you showed only three cables connected to stereo jack, while on video you have four cables going out from stereo jack! Please help to fix, Thanks
Maybe you can say in the videos when you have a discount / promotion for your courses or in the description. I found out by mistake that you have a discount for the basic course.
Since I’m enrolled into udemy promotional program, the prices are set by udemy (not by me). They set promotional prices most of the time.
wait a bit the prices always change
Hi, do you know how to measure how fast is speaker, especially bass, to compare old ones with small magnet with new ones with big magnet (or with open phase plug like your dayton)?
Shouldnt how fast a speaker is be defined by motor force/ weight in motion? Shouldn’t be hard to calculate a mac acceleration value
My DATS V3 shows Re and Zmin same values. which should not be right? can you help me with that ?
in REW Zmin in higher than Re ( ideally it should be). it also tells you Fmin and F3 in which speaker driver having lowest distortions. which is good :)
based on my experience, slightly more powerful speakers, with lower qts, such a system misplaces the resonant frequency of the speaker about 10 hz higher. I wonder what it comes from?
Can i use rca input instead?
What do you think of the Dayton reference drivers? Do they sound as good as they say?
I've worked with subwoofers and passive radiators from the reference line. They're definitely above average. Haven't got the chance to make a speaker using a mid-woofer / tweeter from the reference line. I do have in plan to do that as I have the parts already bought. Judging just by the looks, the build quality is top tier, way better than more expensive speakers for sure.
I have a 100w 4 om 6.5 sub with zero parameters on the internet. So to build a box i had found this method. My amp allows me to adjust volume and bass. Should i make an amplifier version and do i need to turn bass to the max or to the middle and then play with the volume knob to get right voltage?
You need to bypass any amp equalizer or tone/bass controls. Set it to zero. Depending on your amp that is either in the middle or all the way down
you could have calculated an enclosure using the three sets of parameters and compare volume and port length to see if the results are similar or vastly different.
The difference would be negligible. 1dbish tops.
never looked into the DATS, as i dont have a need for it, but 130usd is way cheaper than i expected
Hey your reference calibration resistor is a 10watt27ohm but all I have is a couple 1watt resistors. I can parallel a maximum of 5 will this be safe ?
1 watt is fine, you don’t need to wire multiples in parallel
i purchased das dv3, but i dont now how to measure high frekvency compresion drivers parameters. please have you any ecplanation
Why do you want to measure the parameters of a tweeter?
What usb soundcard with stereo mic input do you recomend? I can only find mono ones
Other than the ones mentioned in the video, I don’t know any other. You have to do your own research. Maybe you have a desktop computer. Usually the mic is stereo on the onboard sound card.
@@AudioJudgement you mentioned that the axagon sound card geta bad results. Will is still work fine enough for impedance for crossover design?
I would recommend you to look for another sound card
Do you think it is possible to use an Audio Interface if my PC does not have the stereo input?
Should work with the amp version. Don't know what exact model of audio interface you have, but I'm guessing that instead of the stereo jack plug, you will probably need dual mono jack plugs.
Hi,
I bought infinity alpha 121W 12 inch sub.
RMS 250w
Fs 33.5
Vas 68
Qts. 0.85
Qes 0.97
Owners manual suggest me to built ported volume of 1.6(45ltr)
And port tuning of 36 Hz
Is it possible to tune the port for 30 Hz is it meaningful to tune a ported box bellow Fs of the driver?
Owners manual also given sealed volume of 40ltres.
As the woofer has lower EBP and higher Qts i am going to built sealed one.
But pls help me to resolve the doubt over ported box question.
While trying softwares to resolve my doubt softweres don't show result for ported box. Because Qts exceeds Qtc of 0.7. Pls help me
You can tune a box below the Fs of a driver. For your particular driver I would go for sealed. Make a box as large as you are comfortable with. The larger the better.
@@AudioJudgement I have gone through most of your videos and it helped me making speaker boxes better. Standing wave video helped me a lot. I will avoid parallel walls for sure. I understand it is also valid not only for the box but also for rooms.
I share the video with my audio friends
Thank you
is there a DATS v2 or 3 teardown?? has some one Pics from the pcb/ chipset?? I bet my ass the dats youses a standart (soundcard) chipset with something like a lm386 at 5v to make .2v. If we know the chipset we can use the dats software. Or we can find a cheap usb sounddongle that we can mod with a lm386 and power over usb.
It so cheap so i would simply just purchase the DATS v3 and dats it!
@@champipy the cheapes thats in my space is 180euro! thats not cheap for me. A 10 -15dollar soundcard with a 0.50euro lm386 and some resistors ans jacks, thats 12-17 euro. thats 10x cheaper.
CSL USB 7.1 Soundkarte extern (8-Kanal) is that en option?!?! it has AUX in thats must by 2 channel. and it has 2 mic inputs mic 1 and mic 2 is only 18€
Buy one and let us know? 😊
Why did you private the old video? At least set it to unlisted or something. I was using it for reference
You're right, didn't think people would save the link. Got the 2 videos unlisted.
you get bulky bro from 3 years ago :D