TATA BS6 & BS4 इंजन पिस्टन और पिस्टन रिंग को कैसे फिट करना है।
Vložit
- čas přidán 13. 09. 2024
- piston ring is a metallic split ring that is attached to the outer diameter of a piston in an internal combustion engine or steam engine. The main functions of piston rings in engines are: Sealing the combustion chamber so that there is minimal loss of gases to the crank case.
Piston rings are designed to seal the gap between the piston and the cylinder wall
If this gap were too small, thermal expansion of the piston could mean the piston seizes in the cylinder, causing serious damage to the engine. On the other hand, a large gap would cause insufficient sealing of the piston rings against the cylinder walls, resulting in excessive(combustion gases entering the crankcase) and less pressure on the cylinder, reducing the power output of the engine.
The sliding motion of the piston ring inside the cylinder wall causes friction losses for the engine. The friction caused by piston rings is approximately 24% of the total mechanical friction losses for the engine.The design of the piston rings is therefore a compromise between minimising friction while achieving good sealing and an acceptable lifespan.
Bhut hi helpful information hai , thank you so much Sirji😊🥳🙏
Very Good information ❤❤
Very good information sir 🌹🇮🇳
Thanks bhai.😊😊😊
Sir Mahindra gaari ka sensar aur ring ke baare me batao na
Thank you so much for making very helpful videos ✨✨✨👍
Very good dost
Good job dada
Sir full video daliye na please engine overhaul ka please
Good on settings.
Very nice 👍 sir 🌹❤️
भाई यदि इंजन बंद है तो चारो पिस्टन किस पोजीशन में होंगे plz बताए
Sir Mahindra track bs6 ka hawa line
Thanks 👍
Piston ring cylinder ke andhar ghumthaa hei yaa nahi
Piston ring cylinder ke andar ghum jata hai. Kitne vi app sahi fit karo.
Yes it's true.
Bhaiya mein apke garage mein apke saat kaam krna chahta hoon
Kahan h apka workshop
Bhai apna workshop kahan per hai
Bhai ek video piston ring ke end me Kitna mm gape Rahana chahie,
Or Piston and liner ke bich Me Kitna mm gap Rahana chahie Iske Upar ek video banaiye
Top ring .25 -. 35
Com ring. . 40. 60
Oil ring. . 30. 40
Baki depend hai apka area ka temp. Usi k hisab se ring end gap set hoye ga
Connecting rod ka position ke bare me
Bs6 main piston front kidhar honna chahiye patta lag jatta hai , but bs4 main top cutting ho gaya to piston front kaise dallen?
Hello sir.Sab kuch thik h
ai bhai shaab kya grantee hai ki Jo engine fit ho raha hai le
ak test mein pass ho ya nahi.
Bhai engine fit bhi ho gya aur gadi bhi bhot badhiya chal rahi. Koi issue ni h
Oil ring top ring right ke samne kat rakhte hain kompressor ring bye saite
Bhai bs 4 bs 3 se alag set kiye jate hai bs 6 ke ring
Ok🖤🖤🖤🖤🖤
Bhai piston ring gum janne se v koi problem nyi hai
Ha but ghumne se control kerna h bhai.
😇😆
😅😅😅😅😅😅😅
Wrong information hai.
Md mukthar
गलत हे तरीके से डालन
Aap pahle sahi se Sikh kar aao
Riga.kevirite.chet.karay
Aap ka mobile number milega bro