Diagnosis of NON STARTING 5HP Briggs Engine
Vložit
- čas přidán 18. 11. 2012
- Filmed September 2011
In this video I show you what is causing this 5HP Briggs & Stratton engine to not start.
Visit my channel for more repair videos;
czcams.com/users/donyboy73...
Buy small engine parts here; www.repairclinic.com/?RCAID=10... - Jak na to + styl
I dont know if you will see this, but you are the one that taught me to be a mechanic. Fours years later with many mowers repaired and a few of my own, i thank you very, very much!
+Cade Ivy you're welcome!
@Derrick Smiley honda gcv
@@donyboy73
What if there is only one dot on your camshaft and not on the crankshaft and when you pulled out the camshaft both of the pushrods fell out at the same time how do you know which one is which?
There is no adjustment down below at the valve you idiot
Thank you Donny.
I'm almost done rebuilding an identical 5HP B&S pump engine for my Dad. Your videos on this engine have helped me a ton👍
When it comes to engine repair you are still the king
DOUG IN MICHIGAN I HAVE LEARNED ALOT BY WATCHING YOUR, VIDEOS I DO THE WORK ON MY SNOWBLOWER MY SELF INSTEAD OF TAKING IT TO A SHOP SAVING ME LOTS OF MONEY THANK YOU FOR SHARING YOUR VIDEOS
some have a cast iron sleeve ad usually you can hone them
Don never looks awkward to me... He does a great job.! :)
I replaced the rings in my 9 series Briggs & Stratton push mower engine yesterday.
Instead of needing 6 pulls to get it as started now it only need 1,my auntie gave it to me in 2008 & it had a broken pull cord in the pull starter, when I fixed it up it took 3 pulls to get it started but then it got worse.
It doesn't burn oil under full load like it used to as it used to use 1/3rd of its oil capacity in 1-2 hours of mowing !
Dony, I use a leak down tester to pinpoint the wear item. Cost of tester is appx $45 US. Good video. Your videos are always informative and entertaining.
yes i try to repair my own car as much as i can, there are a few choices when it comes to replacing an engine,
Still the best of the best! Donyboy you always put out great videos. Keep doing what your doing and hopefully the black flies weren’t too bad up in Skoka this year! Cheers!
mosquitoes now
Hi Dony, this summer I tore down the engine on my 1980 Cub Cadet witch has a 17 horse twin kohler and with the heads off and sitting over night I noticed the left cylinder was leaking a-little oil. Time for a ring job but it still runs great. Enjoyed the vid and Happy Thanksgiving to U and your wife.
thanks, have a nice evening
Burnt valves and scored cylinders were popular on those I/C engines with Koolbore. The cast iron sleeves and alloy valves solved a lot of these problems.
carb and or throttle cable?
I had that with a snowblower try swapping out the coil. I did that and the engine started and fixed all problems hope that helps you
good one! i like your engines too!
Thanks, Dony, Informative as always.
the coloring may depend on the oil you are using
a 4 stroke will be slightly lower, look up compression test on a 4 stroke engine on my channel, thanks for watching
have you ever thought of using a battery impact driver for removing hardware? odviously you wouldn't use it to pit the hardware back on but it seems like it would speed up your production. i use one when i take things apart
thanks
Danny, thanks for your videos. I like fixing lawnmowers and have a question. I have a briggs and stratton engine that I removed from a troy built self propelled. It had good spark but wouldn't run even if I squirt starting fluid on carburetor. I also noticed that the carb choke was fully open on cold when I tried to start it. I suspected a governor problem and opened the engine but not sure what to look for. Also when the piston is on TDC, does the coil need to line up with the magnet? I would appreciate a suggestion. Thanks.
If you observe that you have a lot of carbon build up through the spark plug hole do you recommend taking the unit apart and wire brushing the piston top off or is there a product (like Seafoam) that will take care of it?
yes I have a Milwaukee M18 impact 1/4" drive, I will also be getting the 3/8", my air tools will be collecting dust, lol, i'll make a tool review on the impact
Exellent well explained keep up the good work...🙏👍 i just open my motor it was like that burn but the block was intact...now im going to check the valves if they are loose i fighting with this motor for a week..new carburator new spark plug check the coil for spark clean the inside..inside... still looking for the problen😊
since i can't see it i suggest maybe replacing the carb kit
great video, I learn something in every vid you put out, thanks. Nice tool box, I have the same one in blue, can you give us a sneak peak at what you have in it. Keep up the great vids.
If you think that is funny, you should read the letter I sent to Briggs about 15 years ago when I built my Monosoupape (single valve) Briggs lawnmower engine. I made it sound like I had discovered an Escapee from their R&D department :)
I mailed the letter and 2 photos of it running. A week later a guy from Briggs phoned up, saying it was the funniest letter he had read in 6 months! Then I admitted to him that I had built the engine, not found it at a yard sale. Fun times. Luv your vids!!!
Very informative lesson donnyboy. THANKS
you're welcome, thanks for subscribing
it may have the same problem as this one. think of it this way, when you pull it slowly, the air has time to excape past the piston, but when you pull it fast, it doesent have time to excape, creating some pressure
why was it burning oil ? good vid ! TY Don
Hi Danny like your videos, I have a newer jd snowblower, with a snow max engine, I replaced the coil, but after about 3 minutes of running it stalls and then doesn't run no more than 20 seconds? U think the carb could be gummed up as I never used it one whole winter.?
i'll try
thanks, I say that because I always joke with people that come in, but I find it hard to smile when filming, lol
Love all you videos! Here's two words that may fill your life with joy, while simultaneously! A Cordless ratchet that has a pair. ( I won't mention names but mine is from Wisconsin) LOL Any link you can reply that will tell me why this craftsman (briggs 6.75Hp) pressure washer pulls but there's no resistance. the fly turns, the piston moves and it spins over quite a few times per pull but with my finger in the plug hole no air. all I hear is what sounds like air from the exhaust droning on the stroke.. Thanks Dony!
Hmmm... I suspect something scored the cylinder wall, and the rings started passing oil in the area; that over a little time 'washed' the carbon spooge 'crescent' shaped clean area from the piston crown. Later, as the scoring progressed, compression diminished to a no run.
Would like to know how long it smoked, and to see the piston & rings in the teardown video!
I have the same engine on a go kart. It seems to have not to much compression but it sure does fly . It revs well and hauls. It feels as if it has less than a 1.5 hp push mower engine. Does it mean it has low compression and could get more power if I figure out why or is that normal
Replaced the carburetor on my 5hp Briggs & Stratton roto tiller ( thanks to your instructions) the throttle works wide open but won't return to idle . Why?
i took the head off of a 12 hp briggs(i dunt even remember why) and decided for some reason it would be a good idea to scrape off the carbon. so i put it at top dea center and went away with a chisel and a wire brush. when i was done i put it all the way bottom center and wiped it clean with a microfiber rag to get any carbon that fell down. i also turned it over by hand a few times and kept wiping until there wasn't any more carbon on the cylender. is there a better way to do it?
Hello Donyboy, first time subscriber to your channel and I have a question. I have a craftsman pressure washer that I hadn't used in a while and when I tried to start it, it wouldn't start unless I used some starting fluid in the spark plug hole. I checked the compression and it was at 30 psi the first time and then added a about .5 ounce of oil in the cylinder and got about 80 psi after pulling it about 5-7 times. Spark is good and the fuel is new after I took the carburetor apart and cleaned it out to include the fuel tank that had some gel like substance in it near the screen at the outlet hole on the bottom. What other things should I check? Also, i removed the pump to make it easier to try and start it. I will take the pump apart and clean it out also.
well explained videos my friend... on my briggs and Stratton 5hp stand up , compression is 90psi,,, checked for spark all good there ,, sprayed starting fluid down the throat ,, no life at all... next step is carb rebuild,, but what baffels me is it should at least run for a few sec, with starter fluid if the carb is bad ,, any tips?
yes it's good to clean it off before it causes damage
thanks, yes i have one, in this case i highly suspected something in here
Hey great videos! Have a question for you, I have a marijama backpack blower and cant get it to start it was running fine about 5 months ago and now nothing. I tried putting a little gas in the carb and it fires up and dies so I am thinking its a fuel problem. I took apart carb and checked the lines still no start. I am thinking it might be the diaphram how can u tell if that part is bad or not and what else can it be? Totally stumped at this point any help would be appreciated. Thanks
I have a 5hp side shaft b&s. It starts fine and runs for about 15mins and the shuts down. If you choke it, it will start and run for about 30 seconds. I'm thinking a coil because I don't know why you would have a fuel problem every time in the the 15 minute range. What do you think?
Good, I see this as a engineering problem.TY Don
Thank you for another amazing video! What would be the proper compression reading for this engine? Thank you for all you do to help us newbies I appreciate you very much.
because of internal decompressor you may only 60psi which is normal
you're welcome
Serious? No. Sincere yes. Knowledgable ... Much so... Keep up the great work!
Mr Donyboy I was wondering if you also work on your own car? It looks like many of then things that apply to small engines also apply to large engines. When you go to replace the engine is there a many choices of after market engines or would it have to be that exact engine model?
i'll be posting a teardown this week of this engine so coma back
do i need to clean the top of the piston in my 2 stroke victa mustang? it runs on 25:1 and our section is like over 1/4 acre so the mower gets a good hard use once or twice a month. thanks
Hey dony, I got a question for ya, have you ever run across Wentworth stuff? A buddy of mine got a cpl bsa motorcycles at an auction reciently n brought them to me to check them over and some of the bolts are way different from standard and metric sizes and I can't seem to find many Wentworth socket sets even online
How do you know when you need to do a valve job?
if you go to partstree dot co you can find a parts list
If your exhaust valve clearance is too small should your engine still run?
MUY BUEN TRABAJO 👍
september 2011
great vid dony i got a ? i have a 98 honda trx300 four wheeler and when i start it it rev's high i mean really high and it stick's if i cut it off and back on it's fine .some times it sticks when i ride it and if i go up a gear it wont stick .... someone said it might be the carb ..do you have any idea's .. thanks john
I fixed a 3hp engine on a rototiller last week that had the exhaust valve stuck in the open position due to a build up of carbon and burnt oil. I finally got it working again by using penetrating oil and gently tapped it back down with a block of wood on top of the valve and hit the wood with a hammer when the valve was supposed to close. Whoever had the tiller last put too much oil in it and was burning oil like crazy.
for summer i use sae 30
Very good
hi what was my grandads old tecumseh 5hp snow blower has scratching on one side of the cylinder,i was trying to fix it but i didnt have any cleaning aersol sprays with me. also the carb was completly gummed up, throttle wont move, choke is very sticky.and the exaust is missing its screws. any hope left in this machine?
dony i have a craftsman 21" 6hp brigs & strat push mover thats leaking lots of oil mostly by d pvc tube & drains by d air filter any sugestion on whats wrong so i can buy d right parts ? thanks
how do i adjust the carburettor on my 2 stroke briggs and stratton lawn mower as it is running quite rich and blowing alot of unburnt fuel and sludge out of the exhaust
Hello Donyboy,
I have an old Mastercraft Snow blower with a briggs motor that wont start. unless I put some fuel into the spark plug hole. I am ordering a rebuild kit , but what else should i look for .??
i had exacally the same problem and i replaced the coil it now runs for hours flawlessly but the occational stubborn start
Hey Dony awesome vid! you are golden!, please when you can do a vid on overheated briggs motor with unseated exhaust seat and BENT valve!
fantastic videos my friend!
thanks
Great Job. !!!! Thanks.
not necessarily
my engine has carbon buildup like that but its not scored yet can you just scrap of the carbon ?
Hi donyboy73 I am trying to figure out what Is wrong with an old Tecumseh engine on an old eager 1 mower by craftsman. I took it apart and the carb and the cylinder look and think the spark has spark
the cabel is fine .. so dose the carb need to be cleaned and if that dont work replaced ?
Which compression tester do you use/recommend?
good job
shit, I picked up a roto tiller off the side of the road and it was locked up, I broke free the piston and sanded the rough edges on the cylinder and cleaned the valves, and sanded the head a little and its ran for years, smokes but runs great
hi i have a briggs and stratton mowett mustang and it doesn't have spark if you touch the coil boot it will shock you but when it has a plug there is no arch what could this mean? ( i have tried multiple spark plugs all the right one for this mower.)
I have learned a lot from u....
Dony what type of oil do u use for heavy use
I'm very confused on my B&S 5HP engine. It has lower compression, about 57 PSI from my test (there's no decompression on this engine), but the cylinder wall looks great, the piston looks great, and an unscientific test of the valves seems to show they are sealing. I put my mouth over them while they were closed and tried to blow through them... no leak. My spark is awesome, but it won't fire. My only lead so far is that the head appears to be very warped. I ordered a new head gasket and am going to plane the head to see if that can get it going! I don't want to junk it, it looks mint inside!
head gaskets or warped head
hello
Are most small engines aluminum cylinder were you can't hone them?
maybe the carb isn't sealing properly there, i would have to see it
You said the large valve is the intake. I always thought the big valve was the exhaust. Are you sure you didn't get that backwards because when you pushed the piston down the small valve did opened to allow the gas to enter!!
i have this problem with a 6.75hp briggs i get a small pop but no start i have checked the ignition and cleaned the carb the plug fires fine but still won"t start this is not an OHV here is what i know if i pull the starter slow an plug hole i get nothing but if it"s pulled normal u can feel pressure escaping my guess the vales have a problem but what do i check? i need help
how much would it cost for you to get that motor running if you had to hone the cylinder etc.?
Dony, how would boring a cylinder and replacing with corresponding rings and piston, not guarantee the engine to run right again?
the faster you pull the smother it will be. ir it may have a decompression lever. my 250cc atv is the same way,so i just hit the decompression lever and give it a flying pull and it usually starts first or second try.
thank you, sounds like my engine!!!
Good vid as all ways!
Well the gasket was the first thing i saw.couldn't see sleeve.noticed the carbon quick to.
I have a 5hp engine where the valve seats and the corner of the block warped the block is in buteful shape untell you get to the valves
Is this the engine you performed the crankshaft swap on?
If you're running a compression test on a mower, do u still need w.o.t??
On my old mower,when I remove carburetor compression stroke is easy like other strokes and when I put carburetor compression is only little bit stronger.So that is probably bad intake valve?
Hi Donyboy73 could you please tell me when you get carbon build up like this video, what is the best way to remove it? is there any risks with scratching? thanks
you can use a soft wire brush lightly with WD-40
try some seafoam
I seen it to next to the exaust valve theres even a little spray on the muffler from the head gasket leak .....good eye man .....I was wating for donyboy to say something about it but he must not have seen it
Hey Friend, Need the manual for magnun 18 kohler (simplicity) for my tractor, do you have? i live in monterrey mexico, and need your help tanks
Question: do i have to replace the head gasket each time i remove it?