HOW TO: Install a Limited Slip Differential
Vložit
- čas přidán 6. 09. 2024
- Installing a Detroit TrueTrac (Eaton, torsen/helical style) Limited Slip Differential into a Ford 9" axle in my 1961 Chevy Apache 10 pickup. This type of LSD does NOT use a friction additive.
Re-using the original ring gear.
Big Blues by Audionautix audionautix.com
Creative Commons - Attribution 3.0 Unported - CC BY 3.0 (goo.gl/BlcHZR)
Free Download / Stream: bit.ly/big-blues
Music promoted by Audio Library • Big Blues - Audionauti...
your wife (?) watching you set the ring gear in the kitchen brought a tear to my eye. When I was a bachelor, I washed carb parts in the dishwasher. I don’t do that anymore.
It's actually all good. My wife is absolutely, incredibly, supportive of my hobby; she lets me do ALL of this. She says she had "passive curiosity, and decided not to have _that_ soup."
Of and yes torsion style is the best, no clutch pack, no noise.
I like this , i just did mine yesterday, dad assisted a little bit, but if he ever needs help i'll happily fit it for him if his clutches (stock)blow from too much torque, a nearly 80 year old doing burnouts, 😮.
Eaton has a plant west of Spencer, Iowa that manufactures a number of parts used in differentials and many drive line parts. So, yeh! Some USA parts. Castings, not so much, like Dana. Chrysler used the same carrier preload screw with a locking bracket bolted so it can’t move.
GM had a procedure to test the “Auburn” disc type also called “Corporate” for a long time. With the trans in gear or park, an adaptor was used on the lug bolts and 1/2” beam type torque wrench. Only one clutch pack would break friction and allow turning. 36-42 lbs. ft. on 1/2 ton pickups and 62-78 on passenger cars. Since more weight is over the rear axle on cars, pickups require less. This is the Min-Max specs and if low, required a new plate kit. Since the pinch point of holding required a “S” shaped spring in the middle, the kit included cross-shaft, spring and friction & steel plates. Placing the heavy car version in a truck would results in hopping, noise and wear when turning. Just info on older GM locking diff’s.
Bearings are cheap, use new ones, adjust for new specs, different from used. Don’t forget the crush sleeve. Tip; use a heavy companion flange tool we’re U-joint bolt. A chain wrench can be used, but place a tube cheater over the lower control arm or leaf spring, 300 lbs. ft. sneak up quick. Be prepared to check for in-out movement. 12 in. lbs. on beam type is used to check rotational force again, new or used bearings. Check pattern with pry bar loading the top smooth area of the carrier wedged in the housing, turn both ways to check drive & coast sides of tooth pattern.
Once again, great video, great information and completed properly. Just change the lube every 30k miles or sooner. GL5 or add limited slip additive, then make some figure “8’s” in the parking lot to break in. Wish we had shop in school. But, it takes equipment & a good teacher. Just like him. Great job!
Lmao 😂 love how your wife was looking at you, in her kitchen lol. That is true love 💕 😂
Luv the missus in the background.
You're awesome, broski! My car (the bigger one) has an open diff...which sucks. haha
G'day from Oz, m8!
Could you educate me? I know my spline and axel ratio but what else do I need to know to find a limited slip differential that will fit? My car doesn't have a large after market base so I may have to use one meant for a different car.
Question: What Eaton part number did your old truck need and which Timkens did you need to use? Long version: Great video. I've got a TruTrac model #913A477 ready for my Ford Transit van with a 9.75" and am trying to track down the right Timken bearings and races. I've measured the diameter of where the bearings get pressed onto the Eaton as a 2.298" and 2.289" and finding only the Timken SET14 to match that spec -- but it's listed as a manual transmission countershaft bearing for $12US. I'm suspicous about fitment here.
You should check with Eaton. They would know.
Helpful nuggets of info . I think your wife was ready to limited slip your butt out of her kitchen ,,, garage yours and kitchen hers . Remember happy wife happy life be prepared for the flip side me-thinks. LOL Good job.
Lol wife looks piss off😂😂 cooking bolts in the kitchen
Torsen. not "torsion".
I was stumped for a minute..... You must have gotten that from the subtitles. I said Torsen (TORque-SENsing), but youtube heard me wrong. I do prefer to call them Helical Diffs.
I’m not sure I want the soup anymore…