Follow this easy guide to replacing the tires on a standard patient transport wheelchair. Save yourself hundreds in continuous wheelchair maintenance and learn yourself!
I have been looking all over the internet for this EXACT information! I love that there's so much out there for people in active chairs but i need as much help as I can get with this transport chair until i can get something else lol
Thank you so much. Zip ties were a great solution. Was able to fix mom's chair by laying it on its side, locking the wheel, then used 2 screw drivers to leverage it on part by part adding zip ties along the way. No hammer needed... Maybe because it is a cheap "Drive" wheel chair
You dont need the special tool - Do it in two steps - first work the tire around the hand wheel, then raise it from there to the rim. Do use zip ties for both steps. Don't even need to take it off the wheelchair. After it is in place I put a mall piece of pipe between the tire and rim, and work it around the wheel to seat the tire properly. Remove the pipe, and your done!
You're video was very clear. I have a question if You wouldn't mind answering. You know those quick release bolts on bicycles, is there a way i can convert my wheelchair so i can tale the wheels off so it fits in my car. And i need a solution for the back rest to fold also. Ty
Thanks for the video. I tried to change the whole wheel (metal part/spokes) using wheels from an older wheelchair and found that the center bolt is not the same diameter. Very little difference, like mabe 2mm. Are all wheelchairs going to have different size bolts for their wheels???
I’ve seen so many comments on other CZcams video. This tyre tool doesn’t work. The only one I can see for sell are from the USA. I’m going to try and make my own. Do you have the size
Hey, man. Looks like that is the exact same wheel, and issue that I have, and is what I was looking for, but can't find. So, that was a nice find... if you answer me, I guess, lol... The handlebars, first I can't even figure out what they are, metal or plastic, then like I said, just like this one, they have that gunk around them. I was trying to clean it off, with a drill brush, scouring pad, sandpaper, but I can't tell what's happening, lol... I am now hitting silver underneath, but the gunk wasn't even gone, arrgghh, lol, wth?? Sounds like plastic, but how is it silver?? Do you know where I can buy new ones, only can find full wheels on Amazon, elsewhere. ty Peace
See if this helps you. Pg 172. We order nearly all of our wheelchair parts from Land & Wheel. I believe they are a plastic outer sheath over a metal tubing on the inside. www.landandwheels.com/343/172/
Naww I'll pass looks like I'll need to replace the wheel Look how your banging on the wheel FFS It could be bent out of wack. . . wobble wobble Na but thanks bruh, whatever works for you Doesn't work for me Ciao
Done this process on 100s of wheels and never had a problem. I am using the hammer on the rubber tire so I assure you it’s fine and not bending the rim. These rims are for transport chairs in a hospital they are plenty sturdy enough.
Thank you for this video. Having more material like this would be exceptionally helpful.
I have been looking all over the internet for this EXACT information! I love that there's so much out there for people in active chairs but i need as much help as I can get with this transport chair until i can get something else lol
thank you. was able to fix my grandmother's chair because of this.
Thank you so much. Zip ties were a great solution. Was able to fix mom's chair by laying it on its side, locking the wheel, then used 2 screw drivers to leverage it on part by part adding zip ties along the way. No hammer needed... Maybe because it is a cheap "Drive" wheel chair
Did you have to lubricate the tire? I'm thinking of trying to do what you did. I don't have that fancy mounting tool.
figured most of this out. Your video made it very clear thanks for a concise easy to follow Method.
You da man this vid helped me.out now.i just have to find the tires thanks for posting
www.landandwheels.com/
You dont need the special tool - Do it in two steps - first work the tire around the hand wheel, then raise it from there to the rim. Do use zip ties for both steps. Don't even need to take it off the wheelchair. After it is in place I put a mall piece of pipe between the tire and rim, and work it around the wheel to seat the tire properly. Remove the pipe, and your done!
Thanks!
You're video was very clear. I have a question if You wouldn't mind answering. You know those quick release bolts on bicycles, is there a way i can convert my wheelchair so i can tale the wheels off so it fits in my car. And i need a solution for the back rest to fold also.
Ty
Thanks for the video. I tried to change the whole wheel (metal part/spokes) using wheels from an older wheelchair and found that the center bolt is not the same diameter. Very little difference, like mabe 2mm. Are all wheelchairs going to have different size bolts for their wheels???
you didnt flip the rim first, instead of fighting the hand rail? hmmm
The hand rail runs into the mounting tool we have mounted into the bench vise
It's 0N anyway ... !
I sure hope it’ll be like hanging a bike tire for me mine are non solid tires
Only thing I don't got is the power tools or any tools really lol looks like I gotta spend some cash
What was the substance you put on the tire before installing. Was too fast to read the container.
We use run of the mill hand soap. Any lubricant will do, we prefer water based so excess can be wiped off easily.
Wheelchair Repair & Maintenance Project In Nepal
Thanks for the comment! I checked out your channel and love the project. Let me know how we can help or if you need anymore information!
Just thinking a plastic mallet would not risk dinging the aluminum wheel ?
What’s with the crushing music?
I’ve seen so many comments on other CZcams video. This tyre tool doesn’t work. The only one I can see for sell are from the USA. I’m going to try and make my own. Do you have the size
Me podrían mandar la dirección por favor yo vivo por Naucalpan Edo de mex
Hey, man. Looks like that is the exact same wheel, and issue that I have, and is what I was looking for, but can't find. So, that was a nice find... if you answer me, I guess, lol... The handlebars, first I can't even figure out what they are, metal or plastic, then like I said, just like this one, they have that gunk around them. I was trying to clean it off, with a drill brush, scouring pad, sandpaper, but I can't tell what's happening, lol... I am now hitting silver underneath, but the gunk wasn't even gone, arrgghh, lol, wth?? Sounds like plastic, but how is it silver??
Do you know where I can buy new ones, only can find full wheels on Amazon, elsewhere. ty
Peace
See if this helps you. Pg 172. We order nearly all of our wheelchair parts from Land & Wheel. I believe they are a plastic outer sheath over a metal tubing on the inside.
www.landandwheels.com/343/172/
@@heartlandmobilewheelchairr6849 Thank you, appreciated.
Onde compro esse pneu
Que # de tornillo es la llave? 👋
Aap ki dukan ya soap kahan hai sir
Why are you using a metal hammer on the wheel and spokes. Use a rubber mallet.
Naww I'll pass
looks like I'll need to replace the wheel
Look how your banging on the wheel FFS
It could be bent out of wack. . . wobble wobble
Na but thanks bruh, whatever works for you
Doesn't work for me
Ciao
Done this process on 100s of wheels and never had a problem. I am using the hammer on the rubber tire so I assure you it’s fine and not bending the rim. These rims are for transport chairs in a hospital they are plenty sturdy enough.