The collection grows, twirlability increasing and the power is overwhelming! Keep it up and look forward to hearing more from you about all things Star Wars....believe it or not!
BELIEVE IT OR NOT!!! Thank you man Much appreciated. The Force is strong with this one. More Videos to come! And hopefully my poor audio will be fixed in the next video LOL
Love the Qui Gon’s saber design! Also I have a question, when you screw in the retention screws, do you screw them on very tight up point where you have to use force to tighten them? Or do you just screw them on until they are just fully in?
It's really underrated IMO I love it. Regarding the retention screws, because I swing it around pretty frequently so I screw them in really tight but only to the point where I can't tighten any more. You don't want to tighten too much because you'll strip the retention screws.
Who else misses all the cross promotion that use to take place? I have such a soft spot for taco bell and I'm petty sure it's cause the star wars promotion
Dood yes!!! I can still remember the commercial with the taco bell Chihuahua, Colonel sanders and the pizza hut employee looking out the grassy hill battlefield on naboo as the droid army was deploying. That lives rent free in my mind hahaha
It's alot deeper than my Luke Skywalker lightsaber and the blade is super easy to secure. The design of the emitter allows for a secure blade fastening
Great question! So it actually unscrews on the top third of the hilt relative to the emitter. Basically right above the ignition button. It's on there tight so you gotta give it a little strength at which the whole top third of the hilt will come off, emitter and all. Be careful when doing so to not damage the pins on the board (proffie/SNV4) you then just need to pull the board chassis out, plug in your USB-C plug right in and your good to go! No need to remove the battery from chassis. I hope this helps!
The collection grows, twirlability increasing and the power is overwhelming! Keep it up and look forward to hearing more from you about all things Star Wars....believe it or not!
BELIEVE IT OR NOT!!!
Thank you man Much appreciated. The Force is strong with this one. More Videos to come! And hopefully my poor audio will be fixed in the next video LOL
This Saber probably much better for spinning then the Luke one due to not having that metal block in the way that can pierce your hand/palm.
Exactly! I love my Luke saber but this is the best for spinning
Love the Qui Gon’s saber design! Also I have a question, when you screw in the retention screws, do you screw them on very tight up point where you have to use force to tighten them? Or do you just screw them on until they are just fully in?
It's really underrated IMO I love it.
Regarding the retention screws, because I swing it around pretty frequently so I screw them in really tight but only to the point where I can't tighten any more. You don't want to tighten too much because you'll strip the retention screws.
I want this so bad. I got Anakins first. It’s either this or Vader
Awesome dood!
I would recommend this saber if you want a replica saber that you can spin with ease. I want the Anakin saber as well!
Who else misses all the cross promotion that use to take place? I have such a soft spot for taco bell and I'm petty sure it's cause the star wars promotion
Dood yes!!! I can still remember the commercial with the taco bell Chihuahua, Colonel sanders and the pizza hut employee looking out the grassy hill battlefield on naboo as the droid army was deploying. That lives rent free in my mind hahaha
:( there hasn't been anything like it in an age. Sad
How far did the blade go into the emitter for securement?
It's alot deeper than my Luke Skywalker lightsaber and the blade is super easy to secure. The design of the emitter allows for a secure blade fastening
How do you charge this one? I can’t seem to find where to unscrew on mine.
Great question!
So it actually unscrews on the top third of the hilt relative to the emitter. Basically right above the ignition button. It's on there tight so you gotta give it a little strength at which the whole top third of the hilt will come off, emitter and all. Be careful when doing so to not damage the pins on the board (proffie/SNV4) you then just need to pull the board chassis out, plug in your USB-C plug right in and your good to go! No need to remove the battery from chassis. I hope this helps!