Aruba Controller: Access Point Configuration and Setup
Vložit
- čas přidán 4. 02. 2017
- In this video, I focus on access points and how to join them to the controller and provision them. I will go over both Campus Access Points (CAPs) and Remote Access Points (RAPs).
Agenda:
Factory Resetting RAPs
Factory Resetting IAPs
Factory Resetting CAPs
IAP Conversion
CAP Controller Discovery
AP Groups
GRE Striping IPs
AP System Profiles
AP Provisioning
CAP HA-Lite/Fast Failover
Layer 3 Mobility
RAP Whitelisting
RAP HA with VRRP
RAP Pools - Věda a technologie
this is amazing. your tone of voice is soothing and well maintained. e-learning should be your future!
your video series is awesome bro..it really helped me and many others.. please keep posting such more videos on other topics as well :)
Just a FYI: As of 2021, Alcatel Mobility switch and access point all use the same interface as Aruba. This video helped me set up a a new Alcatel AP
Awesome, that's what I searching, many thanks for sharing.
Great video series. Thank you.
nice videos , thanks for sharing!
Great Videos! For failover to work, do both controllers need to pretty much be a replica of each other? Or can they be configured differently but be also be setup as failovers for each other?
thanks a lot my dear keep it up
How did you find the AP IP address ? Thx :) I don't have console cable and can't set an static IP....
Is there any chance to use a non IAP Access point as an standalone wlan repeater without any Controller? Thanks for the Video!
Awesome Videos THX - just a note why your L3 Mobility possibly didn't work the 1st time was no "write mem" on master after configuration was set. Hence the Master didn't push/save the config to the locals.
Also HA Fast Failover appears to be instantaneous (no longer than 2 to 6 seconds) when using VRRP IPs with Sync enabled between them, can't recall exact settings of hand .....
Thanks for the feedback on the video, I'll double check the L3 Mobility thing. In my own personal testing, both in lab and in actual practice, the APs themselves failover to the standby controller very quickly with HA Lite, more in line with the 2-6 seconds you mention. But I've seen end-user service disruptions much "slower" than that, as exemplified by the 14 second loss of pings in this video, as well as a similar result at work where I tested failover while on a live video call and measured disruption to be about the same. But, sometimes it is as low as a 4 second disruption.
Thank you so much
can i use ubiquiti ap on aruba controller?
hi, I have one question. You are doing most of the stuff on MC2 as per previous video MC2 is standby why you are not doing all this on MC1. Please correct if i am wrong.
You are correct, and I never even noticed. You will see that I used the hostname "mcvip" to log onto the controllers, which maps to 10.0.10.4, the VRRP address of the two controllers. Since I recommend never pre-empting for reasons I discuss in the master redundancy video, I probably had failover to MC2 without noticing or remembering, and never failed-back. In practice, it doesn't matter which controller is the active master controller, because the controller pair should be identical hardware.
hey i have i Aruba WIFI Controller and APs connecting to it , many of my clients complains that their Wireless devices dissconect from the wifi without them doing anything , do you have an idea why that is happening ?
in my organization using barcode machine so i have created new ssid but i want mac base authentication
Hi. Awesome Videos...Are there any future videos to come for this..
Yes I will be adding more videos as time permits. I have to do these on my personal time, usually on weekends, which is why it takes me a long time to do them.
How to put Aruba AP into monitoring.. I want to monitor the bandwidth usage , CPU load, memory usage, uptime,
Uptime and bandwidth can be seen either from either the controller dashboard or through Airwave. Airwave will also retain historical data so you can see bandwidth over time. For CPU and memory, I'm not sure off hand, so I would either try to find that in the documentation or use the good ole Google.
I have 55 Aruba APs bought 3rd party, how do you obtain the controller? The HP website is attrocious, the Evaluation sign-up form doesn't work and HP do not reply to emails.
how to check ap aruba 225 (not iap) firmware inside controller ?
i need a video how to configure it to use as home router
hello sir... i have aruba93 but i cant deal with it... can u help me
hello ...
how to creat an SSID for connect a users have android only (mobile)
which command through change Controller IP address from old to new
how can filter with MAC ( allow / deny )
How to get a controller IOS for EveNG ?
Where i can find reset button in ap365
No, you can’t convert an AP to an IAP (only the reverse, IAP to AP).
Man well all i can say aruba is not for normal people but people with more network understanding. Great but not for me.
Xem passwifi đã kết nối trên máy tính
czcams.com/video/5hKZjGdDxgE/video.html
Yar hindi ma btao