Build a Tryst 10 Trimaran Sailboat - Pt. 19 - Full build of the two amas (outriggers)
Vložit
- čas přidán 28. 11. 2020
- In this video, I make the two amas (vee hulled outriggers). They took just over 24 hours to complete. The solid gusset blocks are as follows:
Back of ama 185mm long approx. Angle: 45mm x 10mm
Front of ama 210mm long approx. Angle: 50mm x 10mm
After assembly, the distance between the back of the back gusset and the front of the front gusset is 1,170mm
If you like this video, you can buy me a coffee here: ko-fi.com/irishchippy Thank You
This is part 19 of my project to build a cheap trimaran sailboat from plans. It is called a Tryst 10, and was designed by Richard Woods. The main hull is a Duo 10, which can be sailed, rowed or propelled by an electric/solar trolling motor.
Our Amazon page: amzn.to/34rmcMy
Garmin Striker 4cv VIVID with GT20 transducer: amzn.to/3pAvBtk
Snappy plug cutter set: amzn.to/2JiAOFe
Stainless Steel 60mm x 8mm: amzn.to/3mFDGdJ
Honeywell Bionic Face Shield: amzn.to/33KQedb
3M 7502 respirator (medium): amzn.to/2ZsBEof
3M NIOSH P100 filters: amzn.to/35sNCC9
Hand Sander: amzn.to/32qGAvE
My for tools and consumables on our Amazon page. amzn.to/34rmcMy
Products are selected based on ratings and value for money, but we do get a commission on Amazon sales
Tryst 10 study plans can downloaded for free or full plans can be purchased, both here: www.sailingcatamarans.com/ - Jak na to + styl
That was so cool to watch how you spread out the to pieces of wood like that. I would have never guessed that is how it is done!
That is the secret of stitch and glue boats.
Hello Pascal, Eden and the lovely Ciara🍀
Thank you very much for showing in great and clear details how you were able to make the two amas (Vee hulled outriggers) as part of your project to build a cheap trimaran sailboat!
What a talented, skilled carpenter/official boat builder you're Pascal!
Thanks very much, for another one of your great videos! Thanks again, my dear friend for sharing! Best regards/Ned
Thank you Ned. I did nearly nothing this past week, but hope to have her in the water next week.
@@IrishChippy 🌷🙌🌷
Hello Irish,
Again, great working tips and continue with Trimaran production with episode 19. To really know something is about telling it. You are doing this job very well. See you. big greetings.
Thank you for watching. I did not do much this week, as I was busy with work.
I can't wait to see this thing on the water, Pascal.
Hopefully next week. I did very little this past week
Good job Pascal. I'm glad it's you doing all that fibre glassing - I'm itchy just watching! Cheers mate.
Thank you Mark. The fiberglass is okay as is. When you sand it, then it is like insulation fiberglass. ITCHY
Great stuff .....well presented for the novice and pro.
Thank you. I am actually a novice myself, so that helps
Sir! You are a legend.
What a detailed video!
Awesome! I was looking exactly for this. Thanks for sharing the whole process.
Subscribed!
That is great. Good luck with your build, and thank you
Thanks for sharing. These amas look great. And I think they are perfect for calm waters. But maybe 3 reasons why they would not be that good in 50 cm waves ? They are 210 mm in high at the middle. And about 210 mm in width. So if they are submerged 100 mm. They have a width of 100 mm. With a 220cm ama (And with a straigt bottom). That gives a maximum lift of (10x10) : 2 x 220 = 11 kg. But the ama does not have a straight bottom. So at 100 mm depth the maximum lift is probably around 7 kg. From that you have to subtract the weight of the ama. If its 7 kg..You have 0,0 kg of lift .. This means that in "any" wind they will stick very deep. Making turns difficult. And any sideways movement will put high stresses on the boom/ connections...On the other hand. If they were tapered down from 210 mm at the top, to 105 mm at the bottom. You would have (105+157) :2 = 131 x 131 x 220 = 38 kg of lift.. with the substractions.. The net lift would be around.. 25 kg.
Thank you for that information, and thank you for watching
Hi Pascal, have learned a new word. Back home "Ammers" are what we use to bang nails in 🤣. Seriously though, better profile than bamboo, should make the boat more efficient and maybe faster 👍
Hahaha Jon. It is Amas. Bamboo outriggers are mainly for balancing, and they skim off the water from time to time. These hulls will 'dig' into the water when leaning over during sailing. well hopefully. Thank you for watching
They Look Great
Thank you Tom
Those outriggers are looking great!
Thank you Don. Hope you are both keeping safe and well over there.
@@IrishChippy we’re all well and staying as safe from this COVID stuff as possible. Because we have our new puppy I’ve not been out in my shop to do any woodworking in over a month but am having a lot of fun with her. Hope all is well with you and your family.
@@wb_finewoodworking That is good. We are grand here too Don.
just found your channel. I subscribed. I will catch up on all videos on this project later through this week. Cheers! Chuck
Wow Chuck. That is a beautiful Haven you are build. That has many hours
another good explanation.
Thanks again! I am glad you liked it
Good work.
Thank you very much
Gut!
good job you make creativ video i like it
Thank you very much
Good day eh!!! Pascal you are making building a boat look so easy!!! Tell me, is there much odor off the epoxy? Is it hard to mix up? You built these two 'boats' pretty quick, but they look great!!! Take care!!
Thank you Mike. No, there is not much odor at all, compared to some paints. I mix by weight on a cheap kitchen digital scales. 3 parts resin to 1 part hardener. It is very easy to mix as it is thin. I stir for 3 to 4 minutes.
Shorten the bristles of your brushes to 3/4 of their length to make them more manageable.
Yes. For other parts I did. Thank you for watching
Hello, new subscriber from Indonesia 🇲🇨
I'm an American expat over here in Bali going on 12 years so of course I'm very familiar with the traditional trimaran called "jukung'' locally. I am looking forward to watching all of your videos in this series as your boat is very similar to the design I came up with. I'm feeling a lot more confident in going forward and trying to build one on my own. Thanks again.
One question, on the fiberglass tape you're using, what is the thickness and width? I can only find fiberglass tape that's usually used as a replacement for asbestos on pipes, which is around 2-3 mm thick, which seems awfully thick to me. I suppose I could cut my own from a regular sheet of fiberglass. Any ideas would be appreciated. Thanks again for the video.
Hi Pak. I am very sorry I missed your comment. I cut the strips diagonally from 200g (4oz)fb cloth. You can see me doing it in some of the videos. The stuff for pipes is not suitable. I bought the cloth on Lazada as well as the laminating epoxy. Look here: www.lazada.co.id/products/diskon-fibercloth-4oz-meteran-kain-fiberglass-cloth-rajutan-rapat-per-meter-murah-i5702298239-s11152584285.html
Ask this store if the have suitable epoxy www.lazada.co.id/shop/kimiaid1629979840/?spm=a2o4j.pdp_revamp.seller.1.5a794e22NdEhfo&itemId=5229084254
Thank you for watching
Great video! Where did you purchase the print?
What is 'the print'?
Do you have a link for the plans???
Yes. Check the video description below. It is right down at the bottom