Loncin 200 Engine Full Restoration

Sdílet
Vložit
  • čas přidán 25. 12. 2020
  • Loncin 200 Engine Full Restoration
    #engine #restoration
  • Věda a technologie

Komentáře • 105

  • @eduardodaquiljr9637
    @eduardodaquiljr9637 Před 8 měsíci

    Others use crankcase splitter but in your work you split case like butter!amazing dear.

  • @EvgenyTrush
    @EvgenyTrush Před 3 lety +1

    Наконец то сделал подобие мастерской. Картинка стала более приятной

  • @mitchlec8916
    @mitchlec8916 Před 2 lety +1

    Good Work! When you pulled the head off, do you remember if both head bolts on the clutch side had washers?
    Thank you

    • @rustyworkshop
      @rustyworkshop  Před 2 lety +1

      thank you, it was a long time ago I do not remember)

    • @mitchlec8916
      @mitchlec8916 Před 2 lety

      @@rustyworkshop No worries! Thank you for taking the time to reply.

  • @namtech425
    @namtech425 Před 11 měsíci +2

    Good job, these engines are pretty simplistic, and they work great and last forever if you look after the. But am I the only one that noticed the piston is the wrong way around? IN should face towards the intake manifold not exhaust?

    • @rustyworkshop
      @rustyworkshop  Před 11 měsíci

      correctly noticed, but the Chinese piston otherwise would not work

    • @danmackintosh6325
      @danmackintosh6325 Před 11 měsíci

      @@rustyworkshop I was about to comment the same thing, so the piston was marked wrongly? I'm replacing the shift forks & 1st gear in a 167FML currently (very similar but gear driven oil pump and no balance shaft) and didn't notice if the piston was stamped correctly, will have to check if it's correct on this one.

  • @akramkafaar6470
    @akramkafaar6470 Před 2 lety

    This video is going to help me alot, thank you so much. Can you tell me did you torque the bolts by the head and rockers? Is there any timing I need to consider because I'm just replacing my piston rings

    • @rustyworkshop
      @rustyworkshop  Před 2 lety

      adjust the valve

    • @akramkafaar6470
      @akramkafaar6470 Před 2 lety

      @@rustyworkshop just stripped my motor and piston is destroyed, going to buy new one tomorrow. How to I set the timing(if there is) do I just align the pushrods correctly?

  • @DeargMcCumhailMuhBeaches
    @DeargMcCumhailMuhBeaches Před 2 lety +1

    Have you tried one of the big bore kits and a performance cam with stiffer cams for these engines? I have the 197cc version in a TaoTao ATV my nephew wrecked.
    As a hobby, I build Vintage Board tracker replicas, ride them a while then sell them. I usually use used Honda clone industrial engines I can get my hands on cheap, for example harbor freight predator 212's up to the 670 v-twins, mated to a stall converter set up like used on go carts.
    I have wanted to build myself a shifter with a clutch and put some 325-350 wide front tires and 400-500 rear 26"-28" Coker, Dunlop, or Firestone motorcycle tires to register for highway use and keep.
    Seeing as I have the 197cc 4 speed with reverse, I thought maybe I'd try and get as much power as possible. I already did the 30mm re-jetted carb with a 12v low pressure in line fuel pump, and port matched the intake and ported and polished the exhaust port for extra performance. The carb has a velocity stack, and it has a custom welded exhaust header..

  • @TheKapdemelo
    @TheKapdemelo Před 10 měsíci

    Hi and really nice video! I'm thinking on getting an atv with that 200cc engine for roughly 250bucks, and this content is great for studing it since its impossible to fins any documents! Looks like the flywheel pulled out very nicely, did you do any magic or is it easy to do with no specialized extractor?

    • @rustyworkshop
      @rustyworkshop  Před 4 měsíci +1

      these engines are easy to disassemble as a children's constructor

  • @nahjohnniyedavis6043
    @nahjohnniyedavis6043 Před rokem +2

    How long is the push rod

  • @mdacosta7013
    @mdacosta7013 Před 6 měsíci

    have you ever have a intake valve that when setting valve lash will always be tight and will give you 0 air valve lash and i believe that its due to a receding valve and by replacing it the valve will fix the problem

  • @user-bs2xh8sm3t
    @user-bs2xh8sm3t Před 10 měsíci

    AP GY3 yeah 👍 keep your good work

  • @plugmanjohnson9982
    @plugmanjohnson9982 Před rokem +1

    You make it seem effortless. My engine looks very similar to yours and this gave me some confidence until the machine elves took my comprehension

    • @namtech425
      @namtech425 Před rokem

      It is a very uncomplicated engine. Straight forward, just line up all the dots and you should be good. The water cooled version is also pretty easy.

  • @roberteroli7307
    @roberteroli7307 Před 2 lety

    Hello, very good job, a small question, is there a manual to download in pdf? And how is the electronic circuit connected?

  • @eduardodaquiljr9637
    @eduardodaquiljr9637 Před rokem

    the push rods must be labeled intake or exhaust so when assembling again they will not be interchanged dear.

  • @user-lu6yq1uo8v
    @user-lu6yq1uo8v Před 3 lety

    Very good 👍

  • @fidoepic
    @fidoepic Před 8 měsíci

    No limpiarse el filtro centrífuga de aceite hasta ahí todo bien y Si le echas desgarrador quedan las tapas como nuevas le quería todo lo negro pegado también debiste cambiar los discos de clunch y la bomba de aceite

  • @duvanandresduranojeda3828
    @duvanandresduranojeda3828 Před 3 měsíci

    Compañero, ¿de cuantos dientes es el piñon que va debajo del centrifugo?, el que mueve la corona de clutch.
    ¿Es de 23T?

    • @rustyworkshop
      @rustyworkshop  Před měsícem

      Чесно незнаю таких деталей

  • @plugmanjohnson9982
    @plugmanjohnson9982 Před rokem

    Also where did you find all the replacement parts and everything? Also are there performance parts?

    • @rustyworkshop
      @rustyworkshop  Před rokem

      all from China, AliExpress

    • @namtech425
      @namtech425 Před rokem

      Yup all from China - Aliexpress, only performance parts I could find is stronger valve springs and an 250cc cylinder and piston, heavy duty clutch springs as well.

  • @pavolkuruc5807
    @pavolkuruc5807 Před 9 měsíci

    Je to podobne ako bashan200cc?

  • @Hamza-tb2vk
    @Hamza-tb2vk Před 3 lety

    Thanks 😊

  • @knifeknifych7430
    @knifeknifych7430 Před 3 lety +1

    👍👍👍

  • @user-sc8xf8gv8n
    @user-sc8xf8gv8n Před rokem

    IN in the piston means intake , it goes in the side of intake you put it wrong mate

  • @Gokraut
    @Gokraut Před 2 lety

    i have a lifan 200cc 163fml push pod and im not sure if you speak english but i totally ruined the cable connection to my clutch actuator and i can't find the correct one can anone help, i was hoping ididnt have to take it apart but i guess i have to so i can find out which arm will work.

    • @rustyworkshop
      @rustyworkshop  Před 2 lety

      Clutch cable?

    • @Gokraut
      @Gokraut Před 2 lety

      Yes clutch cable my lifan is 5 speed is manual obviously and the clutch actuator where the cable connects is all messed up.

    • @rustyworkshop
      @rustyworkshop  Před 2 lety

      So it is removed from the lid and changed

    • @Gokraut
      @Gokraut Před 2 lety

      @@rustyworkshop I just changed it with a Honda one. Punched it out crimped the new one in and finally found a cable that fits great for my kart. I have a hand shift lever with a motorcycle clutch mounted vertically.

    • @rustyworkshop
      @rustyworkshop  Před 2 lety +1

      @@Gokraut Everything is decided, I'm glad for you

  • @user-ms7oc3eq9f
    @user-ms7oc3eq9f Před 3 lety +1

    👌👍

  • @user-ii6du4jq8g
    @user-ii6du4jq8g Před 3 lety +1

    👍👏

  • @mariagaivolia6181
    @mariagaivolia6181 Před 3 lety +1

    Good

  • @user-dl6yf4ej6i
    @user-dl6yf4ej6i Před 3 lety +1

    👍

  • @josejamiltonsantosjerez3014

    Buenas,en Dominicana donde encuentro respuestas de motor Loncin 200 CR5 año 2015,motor LC163FMLNQ19798?

  • @user-id7pz4tq2m
    @user-id7pz4tq2m Před 6 měsíci

    Bonjour j’ai un moteur 150 Loncin qui pétarade et fait des retour de flamme je pence au soupape je voulais savoir le jeux au soupape admi/échappement sa serait cool

  • @karl-erikwulfsbergstrand4947

    Does this engine have an oilfilter?😀

  • @felipelopez5679
    @felipelopez5679 Před 11 měsíci

    Oíl lubrication armed. Silicon no.

  • @JackFlem-vk7ek
    @JackFlem-vk7ek Před měsícem

    What bike is this engine from?

  • @rafikachache4405
    @rafikachache4405 Před měsícem

    you put the piston in the wrong direction!
    good job though

    • @rustyworkshop
      @rustyworkshop  Před měsícem

      how did you get that the piston is in the wrong direction?

    • @rafikachache4405
      @rafikachache4405 Před 27 dny

      ​​@@rustyworkshopthe "IN" marked on the piston is an indication to line up with the intake, also the grooves give it away too: big groove for intake valve and small groove for exhaust

  • @colinandre3027
    @colinandre3027 Před 8 měsíci

    mw gn yon loncin lèl gen vitès ladanl lumière palumen

  • @Le_supermot_618_braap
    @Le_supermot_618_braap Před 3 lety

    Hello lien of segments and cylinders please 😁??

  • @AndrewGarageU
    @AndrewGarageU Před rokem

    доброго дня . хочу запитати що то за пробка 1:57 і що має бути під нею? там має бути сітка чи магніт. типу фільтра. чи на таких двигунах нічого щоб відігравало роль фільтру не має

    • @rustyworkshop
      @rustyworkshop  Před rokem

      є різні версії я так розумію від року випуску в основному там сітрчка але були і без неї

    • @AndrewGarageU
      @AndrewGarageU Před rokem

      @@rustyworkshop дякую. можливо буду міняти масло гляну що там

  • @Artem103103
    @Artem103103 Před 2 lety

    Поршень установлен не верно, последний диск сцепления - не верно. Мотор отмыл слабо, нагар на клапанах не убрал (или не показал). Картер нужно продувать (видно мелкую грязь). ну и зачем было на герметик собирать? В Украине на него есть наборы прокладок.

  • @1985eugene
    @1985eugene Před 3 lety +1

    Очень интересно, но нихуя не понятно..... Без слов и объяснений. Вырезано много нюансов из процесса разборки и сборки. Я могу так видео снять как я на СТО работаю, и нихера не объяснять зачем я снимаю ту или иную деталь, в чём суть проблемы и что надо сделать что б устранить эту неисправность. Что новое ставлю, что старое можно оставить. Почему клапана не регулировал если снял уже и разобрал всё? Больше вопросов чем ответов.
    И самое главное. Вопрос. Сколько стоит перебрать такой мотор с учётом установки новых запчастей(сцепление, сальники, шестерни если надо вдруг, поршень, кольца и т.д. и т.п.) и ещё стоимость работы мастера? Снятие и установка это отдельная сумма. Не проще купить новый мотор и сразу заменить?

    • @rustyworkshop
      @rustyworkshop  Před 3 lety +1

      новый стоит 500 $ ремонт старого в районе 100 $ канешно смысл есть ремонтировать старый

    • @1985eugene
      @1985eugene Před 3 lety

      @@rustyworkshop Так это сумма общая с работой и запчастями?

    • @rustyworkshop
      @rustyworkshop  Před 3 lety +1

      Да

    • @1985eugene
      @1985eugene Před 3 lety

      @@rustyworkshop Тогда одобряю ))) Разница в 400 баксов это ощутимо. Вот только узнать в каком городе можно это сделать. Даже есть вариант, если это не Киев, то можно отправить Новой Почтой.

  • @pj3635
    @pj3635 Před rokem

    Did that piston go in back to front?

  • @harvyd7679
    @harvyd7679 Před rokem

    Thisis loncin 200?

  • @victormanuelhigueraelizald8081

    Pistón al revés no limpió el filtro centrífugo y no se debe usar silicón! Mal!

  • @sttv4653
    @sttv4653 Před rokem

    That piston is turned wrong

  • @pabloromero542
    @pabloromero542 Před 22 dny

    Jojojo..pusiste el psiton al revés..nada de chino ..ni que chino..esta al revés..

  • @orhan3007
    @orhan3007 Před rokem

    One thing's been bothering me which is why these cheap china knock off engines are so underpowered compared to their counterparts. Why is that? Some engines have as much as 15 hp difference

    • @rustyworkshop
      @rustyworkshop  Před rokem +1

      very weak and unreliable engines, have low power because they are made of low-quality materials

    • @orhan3007
      @orhan3007 Před rokem

      @@rustyworkshop yeah initially I thought so too but it can't boil down to just the quality of parts, can it? A little extra friction here and there may cause some loss of power but not enough to make such a difference. I'm thinking it has more to do with bore width and stroke length and even bore/stroke ratio.

    • @rustyworkshop
      @rustyworkshop  Před rokem

      @@orhan3007 That's the case, and still deliberately make the power of the small for fuel economy

  • @anjolouiegallo2288
    @anjolouiegallo2288 Před rokem

    Hahaha... wrong install piston...flip the intake pocket

  • @user-vz7gk5kh3k
    @user-vz7gk5kh3k Před 3 lety +1

    👍

  • @JackFlem-vk7ek
    @JackFlem-vk7ek Před měsícem

    What engine is this from?

  • @user-rk5gn9qy2j
    @user-rk5gn9qy2j Před 3 lety +1

    👍

  • @mariagaivolia3591
    @mariagaivolia3591 Před 3 lety +1

    👍