DIY Double Sided PCB
Vložit
- čas přidán 27. 08. 2024
- Hello, In this video I will show you how to make double sided PCB.
Materials needed
1) Double sided copper clad board - amzn.to/36nrmvV
- amzn.to/3BANYob
2) 130gsm glossy paper - amzn.to/3sOaaqX
Toner transfer paper - amzn.to/34MKanS
3) Ferric chloride - amzn.to/3v34H2p
4) Scotch Brite green pad - amzn.to/3HX8hyE
5) Isopropyl alcohol(IPA) - amzn.to/3I1NjPc
6) Acetone - amzn.to/3gRtttJ
------------------------------
Track: Horizon - Ason ID [Audio Library Release]
Music provided by Audio Library Plus
Watch: • Horizon - Ason ID | Fr...
Free Download / Stream: alplus.io/horizon
------------------------------
Thanks for watching.
====================================
IMPORTANT! Don't forget to:
1) paint it with a protective lacquer after soldering, or
2) coat it with some alcohol-dissolved colophony/resin before soldering, which doubles as flux, or
3) tin all traces with solder.
Otherwise the bare, exposed copper traces will oxidize with time, their resistance will increase and it may cause a lot of weird issues due to voltage drops.
Very good job 👏
very innovative, the copper wires as vias
I had a thought. Would it make sense to drill the vias before etching? That way you might avoid liftoff of copper if your second side is a small copper ring after etching. Also, it would ensure that your print is 100% aligned.
Also, instead of visual alignment, the via holes could be made to be alignment holes as well, so no eyeballing the print through light would be needed..
That's a fantastic idea! I'll definitely give it a try next time. Thank you so much!
Very nice, if you were added uv mask, it would look professional, also can i do the same thing, just instead of using toner transfer method, im gonna use uv film?
One of the best toner transfer PCB's I have seen! What paper is used in this video? Maybe photo print paper?
Iam using 130gsm photo print paper. Thank you.
Nice. How much time in the etch bath? You showed 3 or 4 clips. How long did it take?
And where can i get a drill and bits like you have with the proper size bits? I think you has .3mm bits?
The etching process typically requires a duration of approximately 15 to 20 minutes in my experience. However, it should be noted that when reusing ferric chloride, the etching time may progressively lengthen. Enhancing the agitation of the container during etching can assist in reducing the overall etching time.
The drill bits were purchased from a nearby electronics store. Alternatively, one can acquire them through online platforms. The specific drill bit showcased in the video has a diameter of 0.5mm.
www.amazon.com/Pieces-Polymer-Jewelry-0-1-1mm-Random/dp/B084T4PB1K/ref=mp_s_a_1_4?crid=1OOARF9JKZFN1&keywords=Pcb+drill+bits&qid=1688453567&sprefix=pcb+drill+bit%2Caps%2C393&sr=8-4
Nice video, thanks :)
Buy yourself an electric jigsaw and a metal saw, it will be much easier to cut textolite. Even better than on a minicircular saw.
Good morning, first of all, I would like to say that the tutorial with double-sided PCB was great. Could you put a link to the paper you used, as in the video it seems that the side where the laser printing goes is the shiny side? And if this paper is adhesive? Sorry for so many questions but after so many mistakes making PCB printing, watching your video was a salvation at the end of the tunnel. Thank you very much in advance.
I Am using glossy non adhesive paper. Here is the link to a similar paper amzn.to/44jJb95
Thanks @@ElectroRetro
prefet & amazing. well done 👌👌👌👏👏👏
Please I'm a new student
What app can I use to do this
And I'm in Nigeria, where can I get the copper plate
Quality work👍
Thank you
Beautiful! I'm curious what this circuit was for?
It's a USB to TTL converter.
Hi...Electro Retro .. really great work 👏👏 can I have circuit of PIR sensor Module with 4 leds with out any relay ..I need simple connected with Hi watt 9v battey . PCB designed PDF. Ready to itch
is very nice, can tell me about the width of traces that be used, thanks.
0.400mm
புரோ பிடிஎப் பையில் பிரின்ட் எடுத்தால் ஒரு டிசைனிங் தான் மையமாக வருகிறது மல்டி டிசைனிங் எடுப்பது எப்படி வீடியோ போடுங்கள் எனக்கு உதவியாக இருக்கும்
Can I use an inkjet printer?
@@jerrysmt2959 No
Amazing
Do you flip the board when etching? I only did one-sided-pcbs until now and Iam wondering if I have to change my etching methode for double sided pcbs?
flipping the board is good to evenly etch the board.
@@ElectroRetro thank You
👍
👍🏼
😁👍
👍🏼
Very Nice Bro
Thanks
If you need metalized holes ?
czcams.com/video/fA78303EVQo/video.htmlsi=AQzitudcxsYcnOrU
how about join 2 pcb.??
i`m not see on video
good idea!!!
Smd design in SMD side changed in sample PCB 😢. It need to print with mirror????
Top layer need mirror print.
@@ElectroRetro thank you so much 😊. Tomorrow I'll try it
@San_DIY 👍
What is the minimum width of the wire you could achieve for good results?
0.2mm
Is it okay to print the circuit design on inkjet printer?
No, Inkjet wouldn't work. Must use laser printer.
where is the file to cut rought edges? i cant see the link..
amzn.to/3zlUAHA
Sir,can we use zero pcb board for doing with double sided soldering
Yes
Ni smgh aarha....wash krenge to jo uapr design printed hai sabka copper nikal jayegs na
Cool men
Very nice, one piece is missing : how to print multiple boards per sheet
Is it necessary to mirror the top layer?
Yes
🌝👍
👍🏼
How much time is it taking to you too make wholes for the entire pcb
It depends on the size of the pcb
@@ElectroRetro recently i tried making a pcb at home I used a manual drill same as you for each hole it took around 10mins so how much time is it taking for you per hole. If it's quicker than me any suggestions would be really helpful
10 min is too long. It won't take that long. You should replace your drill bit or you can use a mini rotary tool.
@@ElectroRetro oh how long is taking for you drill a single hole? And what drill are u using
Previously I used a hand drill, it would take less than 1 minute to drill a single hole using a hand drill. Now a days I'm using a small dc motor with mini chuck.
Sir What printer do u use?
Laser printer
@@ElectroRetro Dear Sr,Can use brother hl 1110 mono laser printer?
Yes
can i download the schematic eagle sir?
That pcb is for demo. Its not perfect. It has some errors.
@@ElectroRetro but we still want to try, please send the link of PCB
DOUBLE SIDE CIRCUITS HUMNE DEKHNA SHURU KIYA 1975 SE SHARP NATIONAL KE STEREO SYSTEM SE JO KE ONE SIDE COPER ONE SIDE WHITE CORBON PRESS HOTI
THY
Please never use any type of scrubber to clean pcb.
You will get super clean pcb by
1. Clean it with soft sponge and dish wash liquid (to remove oil and dirt films)
2. After drying with clean cloth,
" use plasto pencil eraser " and rub the copper clad
You will get it super cleaned.
3. Never touch copper side again with bare hand.
Try and reply me.
Thanks for the tip. I will definitely give it a try. One doubt, does this method remove oxidation on the copper surface?
@ElectroRetro absolutely !!
You will get very pure copper exposed.
I tried it.
Will result in better toner adhesion
I used white plasto eraser (used to correct pencil )
Thank you so much. I tried it. I got very good result.