How to run calibration mode Samsung washing machine test motor, check error fault codes.
Vložit
- čas přidán 30. 06. 2024
- How to run the calibration mode on my washing machine playlist on all Samsung washing machine faults • Samsung Washing Machin...
Why is it important to use calibration mode? on all Series 5 ecobubble, QuickDrive, direct drive, digital inverter,
▶ see our other video on Samsung washing machine diagnostic & test mode How to enter Service Cycle and test all functions • Samsung washing machin...
00:00 why calibrate a 6kg, 7kg, 8kg, 9kg Samsung washing machine.
01:06 about How-to-repair.com.
01:16 Samsung Ecobubble calibration.
02:02 Samsung Ecobubble QuickDrive, Direct drive, Digital inverter, calibration.
02:29 Samsung brush motor and digital inverter calibration
It is recommended to run the calibration mode before starting a wash after your washing machine has been installed or moved or repaired and I recommend doing it every 6 months.
Samsung washing machines can automatically detect the weight of laundry and control the water level the pcb needs to know the machine is balanced. Moreover, a balanced washing machine avoids excessive noise and vibration during operation. In addition, you can run the calibration mode if the weight detection value has changed or if you need to proceed with precision detection for the washing machine.
The Duration of the calibration mode can vary.
Normally it takes 2 to 5 minutes to run the calibration mode, but it depends on the model you have.
Please remember to subscribe to our channel and click on the bell notification to get reminders
czcams.com/users/Apart4u?...
Remember to Shop with www.how-to-repair.com and it would help us by posting the video or the website on your
timeline. This helps us a lot and if we really helped you can always buy us a beer how-to-repair.com/help/buy-pau...
Please remember to mark us as your favorites also I would be grateful if you would subscribe to our channel's
social media as this really helps my site and keeps us going.
CZcams. / apart4u
#samsung_calibration_mode #samsung_self_balance_mode #samsungwashingmachine - Jak na to + styl
Thank you. Just bought a machine and this helped conquer the calibration written instruction!👍
Good instructional video. Older Ecobubble, pausing through any wash. Motor test 3E, calibration fixed. Recycling pump had elastic band wrapped around it (gentle hum on test). Stripped pump down, cleaned then satisfying gurgle from pump. Thank you.
thanks 👍 for watching and please remember to subscribe to the Channel as that's what keeps us going in able to make the video for you
Your videos are excellent. You saved my washer!
Please help i can not find the delaybuttpn on my machine
Brilliant. Well thanks to you I have fixed my Samsung washing machine for nothing and calibrated it. It is now running like new. I have also scored major brownie points with my wife because we didn’t have to shell out on a new washing machine 👍🏻🤣
Fantastic! keep here happy Thank you for leaving a comment this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
You're a star, thank you so much !!
Way to go on a side by side comparison for both machines for calibration. These machines always bite me because the displays are slightly different, and it's just enough to make them different for calibration or other diagnostic features.
Very helpful!!!!
Many greatings from Germany.
Schön, dass es Ihnen gefallen hat!
Thanks for this. I think 'CL6' is CLb actually for calibration. Sadly, this hasn't worked on mine. The metal tub still wanders by about 15 millimetres, maybe more. It has shredded the rubber on the inside due to the excessive movement during the spin, and it really shakes and knocks. I have to stop it before the final spin.
Great video! Thankyou very much.
Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. czcams.com/users/postUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm
and this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Thank sir! God bless you 🤗👍
So nice of you Thank you For leaving a comment this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Thank you thank you 😊
Thank u to guide us very clearly I hope u guided us in future as well may Allah bless u
Thank you sir
GREAT video. Is there a chart somewhere that states how much water each program uses when first started (the initial fill)? I would have though it was a set amount.
Thanks for sharing this video
My pleasure
Thanks for this. Must be a Samsung thing as I've never heard of a calibration mode on an LG washing machine 😳
I believe LG do have calibration mode but I have not done the video yet Glad it was helpful! Thank you for leaving a comment this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Thanks!
No problem! glad we could help you Dennis van de Braak this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍
excellent🤩
Thank you! Cheers!
Does this work for the tumble dryers as well?
Hi I've just bought a Samsung ecobubble WW11BBA046AW and I've done the calibration and Selected ecobubble on a cotton wash but the washing machine is filling from the top lefthand side not the bottom as described by Samsung I'm not getting the foaming bubbles for ecobubble mode and I'm using liquid in the main wash draw have you come across this problem with these Samsung washing machines many thanks 😊
Having the 3C error, should I try to calibrate first before eliminating other causes?
Hi, thanks for posting this info. I tried this on my older style Samsung (bought in 2015) and I cannot get it into calibration mode at all. Perhaps its too old? The model number is WP1804WPC - Ecobubble 8.0kg. Any advice is truly appreciated before I call out repair people. cheers
Great information. Thank you for ur time and knowledge sir.
I'm glad we could help you have a great Christmas and a happy New Year 1keykneedeep this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍
Great video but still stopping in the middle of a cycle - any thoughts?
Great Videos! How do I get The “dc” code off?
What do I do when the screen shows a number after the calibration?
My washer is a Midea washer.. The calibration stops at number 139... Any advice?
The manual says it should show clear screen [- - - -] at the end of the calibration, which is not the case.
Thanks.
What do I do the screen gets a number in the calibration at beluga's washing machine? I have Samsung washing machine beluga has Hitachi washing machine I have (/ / / /) Schindler beluga's turn [- - - -]
Great video. My eco with digital inverter has stopped activating the drainage pump.
When I independently power the motor it works fine. I'm assuming it's the circuit board. Is there anything I might be missing.
SlowmoJo I would check when it's on a rinse that you have to 40 volts on the two wires going to the pump. I would love you to leave your opinion on our poll about manufacturers building in obsolescence to appliances. czcams.com/users/postUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm
and this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Hi, my Samsung inverter washing machine is having a built in dryer, but when I use it today the dryer is not working, once I start the drying it is start rotating but there Is one beep without error code and after about 20 seconds the drying ends and the door lock unlock and it's not even last for 2 minutes when the drying cycle stops, and it is not even heating, is there any resetting to do to fix the problem?
What about a wf42h5000aw/a2, is there a video for it?
Hi, mine is starting the calibration mode but not ending showing a "0". When empty it will spin normally to 1400 but when full or when washing it will not spin and all the clothes remain wet. Any ideas how to fix this? Thank you
This worked great on my Samsung washing machine but the only problem seems it's not "saving" the calibration and I need to run this every time I use the washing machine because if I don't then it seems to move a lot more.
That might be the memory Really glad it helped you fix your problem Thank you for leaving a comment this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Hello, how to do the calibration mode on the Samsung Wf218anb?
Hi I'm having issues with my Samsung digital inverter washer. After 20mins of quick wash the machine stops and a 4C appears on the screen panel. What may be the issue??
Pull it out and check your water supply hose, check that your valve is fully open. Failing that, if water enters drum and you still get that error, check/ replace pressure switch and check pressure hose for damage
Hi there. I have a WD0804W8N which is a Digital Inverter EcoBubble washer-dryer combo. By trial and error I found that I can access the diagnostics test mode by holding down the Rinse and Spin buttons (second and third buttons below the screen) while pressing the power button which are different than the buttons you showed in czcams.com/video/5f3SVsxy_4I/video.html However I could not find any button combinations that brings up the calibration mode. Is calibration not possible on my machine or is there a different procedure? Thanks.
I did the calibration but the pump works but the drum does not rotate what problems ?thanks
Hi, what would cause the calibration not to start? I've followed the steps and the clb comes up on the screen then sounds as if the calibration is going to start but it doesn't and goes back to club again.
Me too. Any replies on this issue?
Samsung washer WF350ANG/XAC 05 have Calibration mode?
I try but doesn’t work. Plz help me.
my machine does not start the calibration process.do you know what it could be?
samsung top loading washing machine wa70h4000 diamond drum model panel keys not working. Except on/off switch work. Rest of keys have powers led shows up when turns on. Display shows previous time on each on/off. How do I get into test mode?
Hi! I got samsung WW85K5410WW/SA washing machine. Got it since aug 2017. It suddenly stopped working. Its not taking any water in. Tried calibration but its not spinning. It drains water but thats it. Can you guide please?! thank you .
If your washing machine is not taking in any water then the first thing you need to check is the supply, then you need to make sure that you have the water solenoid is working correctly. There is videos on my channel to show you how water valves work, glad we could help you @kalindpatel this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍
Can you please help me calibrate my top loader if I give you the model number?
In think it's CLB instead of CL6. (CLB stands for Calibration)
you are right glad you enjoyed it please remember to subscribe to
my washing machine now did a full cycle but have sitting at the 1min mark for almost 10min so something aint right but the washing is done.
My drum isnt spinning during calibration mode. Should I reset and keep trying it again?
you might have a problem with the motor Thank you for leaving a comment this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
I have a Samsung WW70J3283 Washer. My drum spun anti-clockwise only while in calibration mode just like your brush motor washer. Shouldn't it spin in both directions?
just an heads up CLb not CL6 CLb =Calibration
Yes it shows cl6 but it doesnt spin the drum. What is the problem now?
Hie can you help me my washing machine is not washing what could be the problem
how to put this model WW-12H8420EW/FQ into diagnostic mode ?
I'm sorry I don't have a video on that one Glad it was helpful! Thank you for leaving a comment this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
CLB for calibrate.
Not CL6
Hi dear Paul im from iraq ...if ther a test & calibrate for samsung WD1172XVM
I'm sorry I do not have the test procedure for this one as it is not a UK model Thank you for leaving a comment this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Good greeting for you from Iraq Police . Calibration mode what is mine? Can you explain me what is it
Calibration mode is to actually make the drum balanced with the printed circuit board by calibrating the motor to the correct RPM if you are looking for test mode this is another video I'm glad I could help you please remember to subscribe to the channel as that's what keeps us going and able to make these videos for you
I tried this on my mother's samsung washing machine. I got a (AC6 code).But the drum is not moving. You. An hear it but nothing is moving.
I have a E3 code that I cannot get fixed .
I tried to my same model but motor only puls rotating not continue fast
My machine doesn't do or display anything when pressing temp and delay end
Most of these machines become so unbalanced anyway that they shake themselves to bits. I've seen it so many times. Door seals split eventually from the vibrations.
At least on US models, their spider brackets are notoriously bad. Laundry detergent will get into the metal fingers and eat away at the support, causing one to fail and shift the drum to destruction
@@bensappliancesandjunk same with the UK models, changed a lot of Samsung drums
My Samsung top washer don’t have a delay end button
How to find the error code thank u
Sorry for the late reply I was away on holiday. I will need your full model number and serial number to be able to assist you properly. Please use the website I'm putting a link below Hi acie I will need the full model number of the identification plate please use our contact us page and make sure you fill out the request of what part you are after and will get back to you within 24 hours normally www.how-to-repair.com/help/contact-us/
this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍
My samsung washer Wf45M5500AP/A5 wont spin
Hi may machine indicating LE 1 way how can I repair
4:20
What is the meaning of this symbol in a Samsung inverter washing machine FE1
dont know sorry Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. czcams.com/users/postUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm
and this is for you czcams.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Hi, have a Samsung ecobubble 7kg machine, model is WF0702WKE. It says in the manual to calibrate the machine and gives instructions but it doesn't seem to go into calibration mode. It just starts to perform the cotton wash cycle and displays a time if 1hr 26mins. Are you able to help please as I'm not getting anywhere with Samsung customer service unfortunately. Got our machine in 2010/2011, worked fine until very recently where its started leaving a white residue on clothes making them dull and makes black clothes look awful! Please help. At my wits end 😂.
How i want to reset the machine
thank you for saving my marriage
I know I help with appliances, never knew I moved into marriage guidance. Glad she's happy
I think this pandemic has taught people the importance of multiple streams of income. Unfortunately having a job doesn’t mean security rather having different investment in the real deal
so true so many change in live can wipe you out in one day
Mine won't do this just keeps switching off
you may have a problem with the circuit board it's well worth having this checked Glad it helped you please remember to subscribe as that's what's keeps this channel going. Thanks 👍
Sorry, but you have to show it more slowly for someone like me. Which buttons to push to calibrate.
When I calibrate my washer doesn't spin
You did not include your model number, so I'm unable to assist unless I have more information. Thank you very much for subscribing.
Huge mistake. You said temperature +delay together while holding the start button. But you press the power button ". 🙄
doesn't work. Perhaps wrong side of the pons
Calibration mode is pointless. 😆😆😆😆😆