At 5:28 when you make your pigtail couldn’t some one cut themselves still since it’s not tucked. Maybe the angle of the video makes it seem like that but I feel like we would get yelled at for that. Great video though I appreciate you posting this valuable info.😎
Hey there, not trying to be a hater, but feel the need to point out what's right. Based on what I was taught in A&P school and per the FAR AC;3.13-1B, the nicks in the wire from the pliers are a no go. Probably more concerning is the "around the world twists" Those are over working the wire making to brittle. It doesn't mention that term anywhere in the FAA rules, but it speaks to the number of twists (6-8 as you stated) and specifically "Safety wire must never be overstressed. Safety wire will break under vibrations if twisted too tightly". Making those around the world twists are doing just that and it will break with a lot of vibration. Same with he pigtail, still need to be 6-8 twists. Its super difficult to get it neat and accurate, but what was displayed would hav been cut by an IA, or instructor.
I am no expert but did wonder that myself when watching this.. I also thought would it not be an issue the many times the wires were worked back and forth at one spot when starting the twists by hand. maybe this is just because it's a demo video, it does look tidy tbf
To be honest, as an inspector, you should be checking fastener tensions too. That's just my opinion. But on a side note your video is very informative. I find my twists coming to the hole a little short or a little too long
I am planning on making a part 2 as well as other videos, but it takes me a lot of time to shoot and edit them. I stay pretty busy so I can't commit to when that will be or how often I will add new ones.
The pigtail doesn't matter quite as much, but you still want it to be tight enough that it will hold the rest of the wire tight. You also don't want it to be so tight that it overstresses the wire causing it to break, either right away or later under vibration. Generally a little tighter than the rest of the wire is ok, and actually can help it stay twisted when you bend it under, but don't over do it.
Opposite, You go from the first to the second clockwise, you would go counter clockwise from the second to the third, then the pig tail would be clockwise and tucked.
You may be a safety wire ninja but you're not a camera ninja - so much of this video is out of sight behind your hand or your arm(s). I'm sure those with hundreds of these under their belt already will disagree but I've not done one before so am disappointed in this, sorry 😥
Great intro for some motorcycle work I’m doing. Thanks.
You’re a safety wire ninja. Wow. Thank you I’m just learning and trying to get better looking safety wires
At 5:28 when you make your pigtail couldn’t some one cut themselves still since it’s not tucked. Maybe the angle of the video makes it seem like that but I feel like we would get yelled at for that. Great video though I appreciate you posting this valuable info.😎
Best safety wire video ive seen so far
Thanks for this tips on how to work better with safety wires.
Accidentally poking your hand with the wire is always fun. 😆
Nice video. Safety wiring is an art that we are all always improving on.
Please explain more the indication of the direction of twist.
This brought back lots of memories... i approve this video, being an ex jet engine mechanic...
Hey there, not trying to be a hater, but feel the need to point out what's right. Based on what I was taught in A&P school and per the FAR AC;3.13-1B, the nicks in the wire from the pliers are a no go. Probably more concerning is the "around the world twists" Those are over working the wire making to brittle. It doesn't mention that term anywhere in the FAA rules, but it speaks to the number of twists (6-8 as you stated) and specifically "Safety wire must never be overstressed. Safety wire will break under vibrations if twisted too tightly". Making those around the world twists are doing just that and it will break with a lot of vibration. Same with he pigtail, still need to be 6-8 twists. Its super difficult to get it neat and accurate, but what was displayed would hav been cut by an IA, or instructor.
I am no expert but did wonder that myself when watching this.. I also thought would it not be an issue the many times the wires were worked back and forth at one spot when starting the twists by hand. maybe this is just because it's a demo video,
it does look tidy tbf
On the second pattern wouldn’t it be better to run the wire coming out of the second bolt, under the twist?? 180 under the twist.
To be honest, as an inspector, you should be checking fastener tensions too. That's just my opinion. But on a side note your video is very informative. I find my twists coming to the hole a little short or a little too long
Who do I contact about using a part of this video for skill level upgrade training for maintenance personnel in the United States Air Force?
Nice Instructions, Thanks.
Is there going to be a part 2, and will you continue to make videos?
I am planning on making a part 2 as well as other videos, but it takes me a lot of time to shoot and edit them. I stay pretty busy so I can't commit to when that will be or how often I will add new ones.
7 level twist
Does the twists per inch on the pigtail matter?
The pigtail doesn't matter quite as much, but you still want it to be tight enough that it will hold the rest of the wire tight. You also don't want it to be so tight that it overstresses the wire causing it to break, either right away or later under vibration. Generally a little tighter than the rest of the wire is ok, and actually can help it stay twisted when you bend it under, but don't over do it.
There are some scenes covered by your arm where I wanted to see how you sent the wire
Thanks
Why are none of your twist 6-8 threads per inch? Just doing it for quickness?
Nice
My problem is the direction to send the wire on th second or third bolt, thanx for the video 🇺🇲✈
Opposite, You go from the first to the second clockwise, you would go counter clockwise from the second to the third, then the pig tail would be clockwise and tucked.
I use the hand to or a drill
How do you properly cut it sir?
Upload more videos please
Great video. Too bad there hasn't been anything posted in two years and the channel is basically dormant.
If you are going to do instructional videos how about keeping your forearm from hiding all your work!
Probably couldn't afford invisible arms on the tool truck!!! Next time he should cut off his arm's before making a video!!!
Did safety wire change. 10-12 turns per inch on runs. 6-8 on pig tails
Page 7-19 of the AC 43.13-1B says 6-8 twists per inch. And that has been the norm for *at least* 25 years, since the last change was in 1998.
CREW DAWGS
Actually I was engine shop and test cell.
First!
You may be a safety wire ninja but you're not a camera ninja - so much of this video is out of sight behind your hand or your arm(s). I'm sure those with hundreds of these under their belt already will disagree but I've not done one before so am disappointed in this, sorry 😥
if this type of instruction was given in the navy...