220V Microwave Transformer to AC Electric Generator 100W DIY ( Type -1 )
Vložit
- čas přidán 21. 02. 2021
- In this video I will teach you how to convert your old microwave transformer into a very powerful electric generator. Its output is going to be AC .
I will also do the difference check for generated power output for with and without core. The generator is going to produce 30 volts AC with a maximum ampere output of 2.75 amps. This type of generator is a monopole generator which is good for demonstration but for full utilization of the coil and the magnets you have to increase the number of stator poles.
Hacksaw Making - 1 = • SIMPLEST !!! Make a Po...
Hacksaw Making - 2 = • How to make a Power Ha...
Mr. Electron 😍😎 = bit.ly/MrElectron
DC Motor Videos = bit.ly/More_on_DCMotors
What's Inside = bit.ly/Whats_Inside_Videos
Repair & Restore = bit.ly/Repair_and_Restore
Make Welding Machine = bit.ly/Welding_Machines_diy
DC Converters = bit.ly/DC_Converters
Electric Bikes = bit.ly/E-Bike_Videos
AC & DC Generators = bit.ly/Generators_DIY
Alternators = bit.ly/Alternator_Videos
Lithium Tab Welder = bit.ly/Battery_Spot_Welders
Follow Me At
INSTAGRAM : mrelectron_youtube
INSTRUCTABLES : www.instructables.com/member/...
===================================================
---- Thanks A Lot For Your Love & Support Guys ---
#microwavetransformer #generator #mot #microwaveoventransformer #transformertogenerator #220v - Věda a technologie
*Join this channel to get access to perks:*
czcams.com/channels/WFbPzBb7dCyCWuBA-DBrMA.htmljoin
*Mr.Electron Patreon's Page* - www.patreon.com/mrelectron
*Hindi Channel* - www.youtube.com/@Mr.ElectronHindi
*Alternator Channel* - www.youtube.com/@mrelectron_alternator
*Watsapp Channel* - whatsapp.com/channel/0029VaQmmRaFCCoWOf7huh3G
www.tubebuddy.com/mrelectron : Install Now and Become a Star Member. ( Use Coupon Code - ShoutBuddy )
Gostei e quero aprender!
Hello now cd u show this with after increasing the coils of copper say u put 4 coils 8 coils or 12 or 16 coils cd u show the current output, and to change voltage u cd use stronger magnets or double neodymium 2 increase have more magnetic flux and also chk what happens when u have more ferrite core as magnetic induction is transmitted throughout the core more the voltage created and with increasing copper raised current or use a bigger armature for more poles or in parallel I mean double the setup of armature on the same shaft with either alnico nd neodymium magnets nd show the difference in current output and voltage too, mainly will like toc after u chg or increase the coils and also the size of resistance of coils by raising thickness of copper wires and putting or changing thr geometric shapes say if put as infinity or 8 how does it affect current production, how 2 scale up current with this set up itself. Double armature, double poles, mag strength n flux by adding, fixing magnets on top of each magnet, doubling cores at back with wires coils and last razing the size of armature vs parallel
Sir cd u give ur phone no
Google Liberty engine 2.0
That's the first time I've SEEN the effect a core has on transformers, awesome!
I've seen that affect far more than once.
Can anyone please let me know is it really workable or not?
I try the same but not getting any voltage or amp..!!!
You are the great sir thank you for giving us your precious time
i love your experiments. ❤️thank you!!
Your automatic hack saw is amazing!!!
I love your content because it's not fake at all,great learning
this is one of my favorite videos..maybe it is because i can see how excited and happy you are with this experiment! very inspiring! (
Hello my friend. Thank you for the video! I love it!
I really like your laugh mr electron!
hahah😂😂😂
Only one that I trust and that is real thanks bud NOW A SUBSCRIBER.
I love you creations GOD BLESS YOU!!!!
Very very nice can't wait to see the results from part 2 :)
You are awesome bro.keep it up,wishing all the best of best.
Parabéns meu amigo!! Exelente 💡 ideia!! Gostei, grande abraço de Marcos Valerio Ciência, Brasil!!!😃😃😃😃😃
Bendiciones Saludos desde REPUBLICA DOMINICANA
Very interesting to see this combination of coil and magnet under real test.
Excellent 👏👏👏
cool that you start using neodymium. keep up this track, sure u will get amazing results soon.
👍👍👍👍very good, Costa Rica Centro América.
Thanks mate, I like your videos, you show it as it is with no bull. Oh yeh, I like your Bonzai trees in the background.
It's a nice application showing how the core increases efficiency in electricity generation, it's a great experimental setup in this respect, yes. If the magnetic fluxes of the rotating magnet rotor cut other coils at an angle of 120 degrees, or if they could take it into fa, even 3-phase AC would be produced, other friends who obtained AC by connecting the windings in series by rotating the rotor in its open core state and 220 volt coils of 2 microwave ovens opposite each other and the top cover core removed. There was also. I mean, most of the magnetic flux of the magnet rotor is wasted with this method while it is rotating, this rotor could rotate as it would be more efficient and surround the winding with its own hollow core, you should definitely try it. Good luck with.
Ficou muito bom 👍👈
Nice experiment bro. But i need the part 2 of this video 👍
Bro love all your videos.. You are ElectroCool 😍
Love your excitement
thanks for getting what i want to know about generator
Bro I received the prize of the last contest. It's awesome. Thank you bro❤️😍🙏🙏🙏
You are most welcome Anooj :)
@@MrElectron sir who is the winner of today's video
@@sudeepbain6941 you are the winner ( i will pin it as soon as i am free )
@@MrElectron Que sucedería si cambiaras el núcleo de acero por el ferrita en los inversores antiguos o ups? solo cambiar el núcleo sin cambiar las bobinas y me gustaría si pudieses hacer un nuevo vídeo con varias bobinas de microondas colocando en los 4 lados y uniéndolas en serie como dijiste.
Nice creativity ❤
Answer:
Increases the electrical resistance of the steel core and to reduce eddy currents.
Therefore the efficiency will increase.
😀😀😀... Kamu Bisa bikin generator... buat yang baik untuk kita semua nya... tapi bikin yang baik kuat dan murah... pasti ada yang butuh jasa kebaikan kamu.... OK salam Damai damailah Dunia ku.. Allah berkati kita semua nya Amin.
Nice demo 4 coils should get 120 volts and being ac you can step up or down with matching transformers
Answer of your question
Because silicone increases the electrical resistivity of steel core and, therefore, reduces eddy current losses.
Congratulations !!! You were the first one to give the correct answer and now you have successfully entered the contest.
Make sure, you are the first one to correctly answer for the next video as well to win the contest.
Contest Rules (video) - czcams.com/video/yM1HGrM2wNM/video.html
Thank you ❤️❤️ sir .
Eric Dollards video the history of electricity he explained how the Atlantic Ocean crossing of the communication cable where the timing of the signals was not correct after transversing the distance. (Dot dot dash dash) Steinmetz wrapped the cable with "magnetic" tape. Because the signal being created by a generated induction around the conductor was also magnetic and not only dielectric. Silicon insulates or isolates the plates apart. Like the covering of tape. So the coaxial cable was created. And the timing of the magneto and the dielectric was maintained through better more appropriate induction. Not being as much effected by sea water (electrolytic) induction. The telegram wire impulses of charge travelled simultaneously held together as one magnetodielectric charge impulse across the vast distance.
The inductance created in the transformer is forced increase in the magnetodielectric capacitance by plate separation.
@@niktesla3939 no its just magnets adding up, the more you add more the magnetic flux, more the emf induced, and more the resistance ie coiling of copper u cut more current u generate
Very nice sir
Nice video ..
Ok felicitări ❤❤❤
What was that shaft with neodymium magnets from (around 2:10)? What motor?
Nice 👍
Excelente
Nice video ❤️❤️❤️
5:00 you may consider another coil, on opposite side of rotor, in phase with other one.. wired in series or parallel ???
Waiting 4 part 2
GOOD.WORKR
Thanks
Good job
Very good
Nice
Hola amigo me gusto tu video es simple y muy bien explicado, pero dine que opinas de liberty engine 2.0 ?? Tu crees que sea real ??
A experiência e boa agora entender o prazer que ele está tendo é porque gosta mesmo de eletricidade 🔌 parabéns aí porca voz do deserto Río de janeiro 🇧🇷
Hi my question is how much push force do a microwave transformer produce in pounds of electricity force?
I know microwave transformer have a lot of voltage
But how much in pounds of electricity force thats what I want to know. When a power line get cut and the voltage cut line is moving up and down on the ground how much electricity force pounds is making it move like that? It must weigh something?
Silicon is added to stampings to reduce the Reciprocating flux from rotor till I assume, it should help in reducing back EMF, please correct me if wrong, I will highly appreciate it, great video and God bless
Kya hum practically ghar ke liye bhi 12 v ki motor use karke bijali use kar sakate hai?230v ac
The relevant point to focus on will be the mechanical input vs electrical output, which is not going to be anything special, when compared to any other standard generator, because Lenz law is applicable. But as a normal generator, your efforts are commendable.
ممتاز
I have an alternator with 6 wires, how do I wire it for 220 power for my homw ?
Neodymium magnetis from what kind of motor?
❤❤❤❤❤👍👍👍👍👍
From the other coil if would get 110 volt and 0.5 amps should start mobile charger or even low energy TV.
pay attention to your core line direction as relates to the moving magnets arc, the ceramics where cutting 90 deg from the laminate line direction...hence more induced emf +- bemf.
however the neo's even with more millihenries where zero deg inline with the laminate line direction so very little magnetic conduction/induction on the separate laminate plates...
cut the laminates with a hole saw to make them curve around magnets arc to get better& closer magnetic coverage.
remember 'Professor Eric Laithwaite: The Circle of Magnetism - 1968' see them all.
showed a sausage shaped coil is better as you waste less magnetically lines uncut 90deg copper doing nothing to make a collapsing magnetic field = more bemf ,its about inducing more (delayed) magnetic zones so their collapse can transform back to current in the less resistive path copper in this case etc
get a role of cheap super thin magnetic 'steel foil', stamp a bunch of separate laminates out of that, use super thinned out wood glue to stack the laminates together, see the improvement for a little more effort & fun
making an auto stamper machine.. stick some extra old magnets on the laminate stack, on the far side away from the spindle to magnetically assist the transient field, more fun
keep in mind WHY the laminates all around the shading ring/pole induction motor make it work & the job the bits of wound copper 90deg offset from the main ( inducting) coil is there ,... to take up the collapsing delayed fields in the laminates and provide the ringing offset push etc.. think like a real visual engineer not a computer optimisation tool simulation..
Best generator
brother i just try to experiment this one but not found any voltage and amp...
Any suggestions?
Where m i wrong?
I made the same test and uses a 8pole Magnetholder driven by a 20000 rpm Motor. I could generate approx.80V AC.
👍👍
silicon content of about 3.2 mass %, which increases the electrical resistivity of iron and therefore reduces eddy current losses (ans of ur questions):)
What is the size of the neodymium magnet ???
Microwave Transformer ki cal kitne bajane ki Hoti Hai primary secondary
Hoc tu dien :Tuyet (bangia) cong =chung .tuyet cong=tuyet chung
Lanh = ret =buot
Please make a flywheel generator and upload. Tell me what you can do using it.
How can get a big motor. ........by the way good job
Thanks ! My upcoming project will help you with that 😊
Hi भाय जनरेटर मे मॅग्नेट कीतने लगाने चाहीये दो कॅईल रहेगा तो
من اين هذا القلب المغناتيسي اجيبه منين like Thank you
Bro
Please less then space between router and coil
Than you see the the current will he generated very high
bro can you provied 60hdzes 240/120volts transformer simpel dizine
Esse. Motor. Aguenta. Fonsionaro. Uma. Máquina. De. Lavar. Roupa
Five stars 🤩
👍
How many turns is the coil
Mr electron I need your help
Eddy current?
😁👌👍✌🖖😎
Microwave Transformer ki cal Mein kitna vajan hota hai primary secondary mein aur kaun se number ka tar Dala hota hai
2 bobinas mas, para sumar el amperaje o voltaje y un transformador a la salida para elevar la tension a 220v
English ?
??? Is a rickshaw motor or is it a ripsaw j .a. question
The current in air core test cannot be zero. You should use special multimeter.
Microwave Transformer ki primary call banana sikhayen
How can i get a microwave transformer???
Can anyone please let me know is it really workable or not?
I try the same but not getting any voltage or amp..!!!
Microwave transformer coil jagananda millega.
Eso lo hace mi hijo de 10 años necesito ver resultados a otro niveñ
NÃO ENTENDI ?, PRA QUE SERVE UM GERADOR SE DEPENDE DE OUTRO MECANISMO QUE UTILIZA ENERGIA POR MEIO DE ELETRICIDADE , ??????
Hello Mr electric can you make me one of those generator to use in my camper please how much it will cost me 8 kilowatts green generator
From where can I buy microwave transformer at low price??😊
Can you finish this experiment
Microwave ki transformer ki call banana sikhayen
Khilona
Hi
I know there is a way u can use the satellites to get free wifi
850 watt drive input and 100 watts output
Traduz. Para. Português.
Now run a sterling engine in the middle of this
Please measure the frequency
The engineering mindset taught me
The AC frequency is always 1/2 the rpm of the generator converted to hz
Since he's rotating it at 2500rpm
Maybe
Just maybe
The frequency is around 1250per minute
Or ~ 21 Hz
F = (p.n)/120 ; where p= no. of magnet poles, n = speed of shaft
=> F= (8x2500)/120 = 166.67 Hz
@@MrElectron thank you