Dual Mass Fly Wheel VW T5 T6 DSG - Easy Remove and Replace DMF
Vložit
- čas přidán 8. 09. 2024
- Step by Step tutorial on how to remove VW T5 T6 Transporter, Multivan, Caravelle DSG gearbox and replace the DMF Dual Mass Flywheel. Full details Includes replacing the spigot bearing and tools required.
Here's a link to the blind bearing puller
amzn.to/46ZqCIm
0.00 Start Description
1.05 Starter Motor
4.55 locating gearbox top bolts
5.14 Removing drive shafts
9.50 Removing Subframe
29.00 Tools Required for the Job
#VW #DMF #flywheel
Easy removal? So glad it wasn’t hard.
Very well done, great video, I’ll give you a call when mines due for replacement.
It’s a motivational channel. 😂 Easy in hindsight. We Cant let these DSG’s get the better of us ! You can do it 👍
Another great video!
I was asking myself why you needed to change the DMF and then I read another response...
I previously thought that it was the clutch packs that were rattling around, but now it would appear that I need to contemplate a DMF swap.
Having done the cam belt and the aux belt, plus all tensioners and idlers, ours is much quieter, but listing to it underneath when it's cold, it chatters away!
I can do it (I guess)!
Absolutely, the video shows you the way. Let's us know how it goes. You can do it 👍
Thanks mate. Encouraging and very helpful!
Thanks for the positive feedback. Let us know how you get on with the job. You can do it 👍
As you said easy job thanks for that video really helpful you were lucky because it was fwd i have to do it same job but in 4 motion dsg 😭
Well done, That’s why I stuck with FWD and snow chains . You can do it.👍
Very good video, what brand is the dualmass flywheel please? Sachs or Luk? and what is the part number ?
If I remember the one is this video essay LUK. Sorry part number is not at hand. Keep us posted how it goes. You can do it 👍
Much easier on a 2 post ramp , you can do everything from underneath !
Thanks for the feedback , although not everyone has access to a 2 poster. You can do it 👍
ah mate....this is kicking my ass. I am trying to get the DS out, but using the lever, it us definitely not "just popping out". I'm cranking on it and doesn't budge. I'm shafted...pun intended. OK....I'm going back into battle. I can do it....hopefully. cheers!
Agreed you can do it. I was thinking you get to this point as you have to really yank the drive shaft out. Much harder than feels normal. Have a big lever between the back of the DS and against the box. Max sure it’s on a sturdy part of the box so as not to damage. I did it from under. You can’t slowly spring it off by hand. Needs to be hard sudden force. Lever the DS so the clip is under a bit of tension then give it a yank and it’ll come off. You can do it 👍
@@YoucandoitwithJules I got it out, but my DS has a female end with the male stub shaft coming out of the gearbox. I see your DS has the male bit with splines and the clip at the end. My clip was on the stub. However, there was no clip I think. I can't find it. I mean, there must have been a clip, but it's not on the stub DS in the groove. I can't imagine I am simply meant to slide it back on without a clip there...right? It's mind boggling really. what an adventure!! you make it look 1000 times easier...my hat's off to you mate.
@@bradfordgoerss3242 well done. Indeed there should be a clip. Can you send a pic ? You can do it 👍
The CV joint at the wheel side fits on the male side of the drive shaft.
I will post a video to my channel and send you the link. cheers
Very good video thank you 👍
Hey thanks for the feedback. Keep us posted on how you get on with it. You can do it 👍
Excellent presentation ..thanks..
Thanks for the feedback. Keep us posted on how it goes . You can do it 👍
Thanks for the feedback. Keep us posted. You can do it 👍
Excellent video!
Thanks for the feedback. You can do it 👍
Thanks so much
Thanks for the feedback, lets us know how you get on. You can do it 👍
What was wrong when you had to change the clutch and dual mass flywheel? Was the van slipping in gear? I have a 07 transporter 2.5 dsg and it started slipping in gear when driving im thinking I need to change the clutch
Luckily I haven’t had to change the clutches just the DMF. You can adjust the clutches with the correct software and that might get you out of trouble. Haven’t done it my self thou. If it’s slipping in gear then definitely the clutches. You can do it 👍
@@YoucandoitwithJules are the clutches easy enough to change? I take it you would need to open the gearbox up?
Can you buy a clutch kit for it?
@@mandylad I saw a video online about changing clutches on a dsg not this exact box but gives an idea. Check out CZcams. You must be able to get the clutches from TPS if in the UK. Hope this helps. You can do it 👍
@@mandylad
This should give you a head start...
czcams.com/video/AKzjIHNLKz8/video.html
Not to steer you away from You Can Do It, just reference YT video in regards to clutch overhaul.
Hi, just watched your video on DMF replacement. Can I ask why it needed replacing? My T5 had a vibration around 1500 rpm and several people suggested it was a problem with the DMF, so I wondered what your problem was. Cheers
Try watching my video with DMF sounds. It explains. You can do it 👍
Hi there , Very good video
Do you have one on easiest way on how to replace engine on a T5 Bi turbo DSG Auto ?
Thanks for feedback.Havn´t had to do that job yet so no video from this channel. You can do it.
Thanks for the another good helpful video from you.
Do you know how to get the stub shaft out and when is out will be oil leak from the gearbox or not
Hi if you watch the video I show how to get it off. No oil comes out. Keep posted. You can do it 👍
@@YoucandoitwithJules I didn’t see the stub shaft,only the driveshaft sorry
@@bu4komobil hi just so we understand what do you mean buy stub shaft ? You can do it 👍
Is this the 7speed dsg box? Seems to be all garages ask ams as soon as I say it's a 7 speed they say they can't do it. I'm wondering what's so bad about the 7 speed if it's different. I have to do this job on a 2016 t6
Yep it's a 7 speed dsg box. It's easy to do if you follow the video to see what's involved. If the garages are refusing to do it then they are not very experienced in VW's. The difference between the 7 speed and other dsg's is that the clutches are wet and inside the gearbox. They may be thinking you want the clutches replaced which is big job. Changing the DMF is easy as there's no clutch to undo. Hope this helps. You can do it 👍
After popping the drive shaft off with the crow bar, do I have to replace the clip or will the old one still work? just slide it back on and hear a click?
Yes. You can do it 👍
When you put the pilot bearing in how far does it go in? All the way or? Also how to get an accurate 1/4 I'm told if not 100% can get shifting issues
If I remember I show a pic in the video. I noted how far the old one was in and made sure it went in same depth. When I get a chance I’ll re watch the video. Let us know how you get on. Shifting issues should not be a problem as it just supports the end of the shaft. You can do it 👍
If you are talking about the 1/4 for torquing the flywheel bolts. I just do a visual 1/4 turn by noting where the handle of the wrench is. Looking at the video it looks like the needle bearing is set in about 4mm deeper than the edge of the hole your setting it in. Theres also a small hole in the end of bearing cage which you can use the see and test its seated correctly. You can do it👍
How mouch you will charge for labour?Cheers
How much did you tighten the fulan screws the manufacturer says 90N was a very nice video
Hi not sure as don’t have details to hand go with what the manufacturer recommends. You can do it 👍
Thank you for the nice reply. I have a question. I have ridden the Fulan twice and it broke. After the break, the car started to move with a sound and no speed. What do you think is the reason for this thing? Do I have to walk it quietly for a certain kilometer in order to respond to the boats?🥰
The clutch magically disappeared did it go back on?
I never took the clutch off. It's a DSG with the clutches inside the gearbox. You can do it 👍
Blind hole puller where from please
I got mine from Amazon or Ebay. Not expensive… Hope this helps. You can do it.