For those looking to understand the process 0:27 remove torx screws on battery cover 1:20 look at connector between battery and controller 1:33 plug in charger still shows green = no charge 1:51 based on no charge, the issue is between controller and battery charge wire (tries wiggling to see if he can get a connection to make it turn red 2:10 holding down the wire to the controller makes it charge, so there's an issue in the connection between the connector and controller 2:49 test for continuity between charge port and other side (see which wire has a bad connection) 3:23 by sticking a pin and wiggling, looking to truly verify the wire with bad connection (probably cuts the video to do some soldering here?) 4:11 plug in battery to controller connector 4:45 charging is working consistently everything after this is just validating and reassembling the scooter
@@supermandcuteheart55 wire wiggling didn't do anything, health of battery should be okay. Maybe error in PCB. Sometimes (1/20 chance) it charges for maximum 2 minutes with increasing % battery and then all of the sudden stops charging after only 1-2% has been added.
Sir NAPANOOD KO VODEO MO. ganyan din problema ng g30LP KO. KAKABILI KO PALANG NUNG DECEMBER 24 2021, ngayong 29, ayaw na mag charge , stay green nlng ung charger. Sir ano # mo. Gusto sana kita makausap mkapag tanong ako ng konti about s G30LP.
Thanks for the video Superman! It'd be great to have your voice in it describing what you're doing, though :D Still appreciate the video as I'm hoping the issue with mine is similar!
Sir pwede ko ba makuha # mo, ask lang ako konti about sa G30LP. NEW SUBSCRIBER MO KO, AND NEW USER DIN NG NINEBOT. NA SHARE KO NARIN SA GROUP NG NINEBOT SEGWAT UNG VIDEO MO. DUBAI AKO. THANKS SA VIDEO$$$
The problem with Sagui they have a wonderful machine, but the garbage customer service I will not buy them never anymore. They probably have a recall on this machine.
For those looking to understand the process
0:27 remove torx screws on battery cover
1:20 look at connector between battery and controller
1:33 plug in charger still shows green = no charge
1:51 based on no charge, the issue is between controller and battery charge wire (tries wiggling to see if he can get a connection to make it turn red
2:10 holding down the wire to the controller makes it charge, so there's an issue in the connection between the connector and controller
2:49 test for continuity between charge port and other side (see which wire has a bad connection)
3:23 by sticking a pin and wiggling, looking to truly verify the wire with bad connection (probably cuts the video to do some soldering here?)
4:11 plug in battery to controller connector
4:45 charging is working consistently
everything after this is just validating and reassembling the scooter
Ha ha. Dude cuts out the most important part of the video. Thought I was going crazy. Thanks for breaking it down.
@@nathanfarrugia2834 i had to watch it 3 times to make sense of it
Wow.. thanks for sharing
Gracias, I'm going to try this tomorrow at work because my Max has a bad contact for charging, should be the same problem. Good video ✌🏻
may be, just try the wire wiggling ,during your charging and also check the health of your battery.
@@supermandcuteheart55 wire wiggling didn't do anything, health of battery should be okay. Maybe error in PCB. Sometimes (1/20 chance) it charges for maximum 2 minutes with increasing % battery and then all of the sudden stops charging after only 1-2% has been added.
@@ANGUS2nd ok, you can you check also your charger, try to use other charger but be sure its desame voltage, good luck
Sir NAPANOOD KO VODEO MO.
ganyan din problema ng g30LP KO.
KAKABILI KO PALANG NUNG DECEMBER 24 2021, ngayong 29, ayaw na mag charge , stay green nlng ung charger. Sir ano # mo. Gusto sana kita makausap mkapag tanong ako ng konti about s G30LP.
Thank you!
Thanks for the video Superman! It'd be great to have your voice in it describing what you're doing, though :D Still appreciate the video as I'm hoping the issue with mine is similar!
thank you...
Thanks for sharing
Mine is doing the same thing but the screen is not coming on at all. Brake light blinks slow for a couple of minutes then goes black.
Sending full support from Ronskey
So I need to stick needles into the port and wiggle them around?
that is only for diy testing,if you you have the right socket that fit to the terminal side for testing ,much better
Where can I buy the tools I need to open the back panel cover?
just look in the hardware or automotive tool shop,ask for star allen key with the hole at the center
what size torx wrench?
could do with a bit of varnish on those nails.
You gotta be gay to look at another man's nails smh weirdo
Pls add some discription
...
What was the fix... Just reconnect plug
the negative wire is open... I just solder it again.
Sir pwede ko ba makuha # mo, ask lang ako konti about sa G30LP. NEW SUBSCRIBER MO KO, AND NEW USER DIN NG NINEBOT. NA SHARE KO NARIN SA GROUP NG NINEBOT SEGWAT UNG VIDEO MO. DUBAI AKO. THANKS SA VIDEO$$$
I just got mine and took it out the box and it doesn’t work. Ninebot is trash
maybe factory defect
@@supermandcuteheart55 it was
The problem with Sagui they have a wonderful machine, but the garbage customer service I will not buy them never anymore. They probably have a recall on this machine.