Can this be connected to a float switch? I need a controller that has a manual run/stop button but can also be connected to a float switch so it automatically stops the flow when water reaches a certain level in my container.
This product looks awesome..... Quick question once I set it to flow 300 gallons, when its done do I have to set 300 every time I want to use it or do I just hit run? Will I have to program it every time the power goes out or is the information stored?
Hello I have been using these now a couple years. I think they are great. But now I have an issue where one of my units is not measuring any water flow. I need help please. I cannot call the number from the USA - is there a manual or do you have an answer? I replaced the plug. I replaced the flow sensor. It worked briefly but now all numbers are 0. When water runs through it it does not sense any flow at all.
For some reason my unit ( I use gallons instead of liters) is off by a value place. 5.00 gallons is half a gallon 50.00 is 5 gallons 500.00 is 50 gallons and etc. is there a fix for this?
DIGITEN Victor thank you for the quick response. I purchased 5 dc15 units for my business. I would greatly appreciate some detailed instructions on how to adjust the k value and calibrate. I have large tanks I fill with these units and so far I love the product. I have filled a 200 gallon tank. I have to enter 2000.00 to do so. It is very close but delivered about 180 gallons when I entered 2000.00 - I pressed the up and down buttons simultaneously to change to gallons successfully. I would like to be able to enter 0200.00 for 200 gallons and it deliver the 200 at least closer to it. Right on spot would be great too. Thank you
DIGITEN Victor my current k value is 1.98 which is what it came at so 9.00 ? I filled 300 gallons last night (entered 3000.00) and the system delivered 275 gallons. So does the k value at 0009.00 sound about right ?
DIGITEN Victor how Do I determine accuracy? If the water pressure changes will the k Value also need to be changed ? Thank your for responding I was loosing my mind
how do you determine the right k value? do you have to constantly be calibrating it?
Can this be connected to a float switch? I need a controller that has a manual run/stop button but can also be connected to a float switch so it automatically stops the flow when water reaches a certain level in my container.
will the seals hold up to hot water, strait from a hot water heater?
Can I set a date and time when it shuld fill up my tank ?
Does it measure Imp.gallons or US Gallons
This product looks awesome.....
Quick question once I set it to flow 300 gallons, when its done do I have to set 300 every time I want to use it or do I just hit run? Will I have to program it every time the power goes out or is the information stored?
The setting value will be stored when power off, You only press the RUN/STOP button to deliver 300 gallons automatically.
Does someone know if the sensor and solenoid valve can withstand use with corrosive liquids? Thanks!
In general, some sensor and solenoid valve work with the liquid of weak acid and weak salt.
Hello I have been using these now a couple years. I think they are great. But now I have an issue where one of my units is not measuring any water flow. I need help please. I cannot call the number from the USA - is there a manual or do you have an answer? I replaced the plug. I replaced the flow sensor. It worked briefly but now all numbers are 0. When water runs through it it does not sense any flow at all.
Please send your questions to email: service@digit-en.com.
the flow of my system is throttled when I occupy the controller. Does the K have something to do? I already changed the valve and nothing ..
K value is different for different flowmeters, if you have any questions, please contact us with email: service@digit-en.com
E possível definir vazão em litros por minuto?
@@marcosalamino9192 No. You only monitor the flow rate
For some reason my unit ( I use gallons instead of liters) is off by a value place. 5.00 gallons is half a gallon 50.00 is 5 gallons 500.00 is 50 gallons and etc. is there a fix for this?
Hi, what is your flow sensor? I think you need to increase the K value according to your description.
DIGITEN Victor thank you for the quick response. I purchased 5 dc15 units for my business. I would greatly appreciate some detailed instructions on how to adjust the k value and calibrate. I have large tanks I fill with these units and so far I love the product. I have filled a 200 gallon tank. I have to enter 2000.00 to do so. It is very close but delivered about 180 gallons when I entered 2000.00 - I pressed the up and down buttons simultaneously to change to gallons successfully. I would like to be able to enter 0200.00 for 200 gallons and it deliver the 200 at least closer to it. Right on spot would be great too. Thank you
Hi @@therealMFfeelyaheard, You can reduce the K value by 10 times（may be 9 times).
DIGITEN Victor my current k value is 1.98 which is what it came at so 9.00 ? I filled 300 gallons last night (entered 3000.00) and the system delivered 275 gallons. So does the k value at 0009.00 sound about right ?
Please contact DIGITEN customer service, thanks@@therealMFfeelyaheard
what is the thread of the temperature sensor?
what is the thread of the temperature sensor?

M8 thread.
Hi, can I connect more than one water flow sensors to this unit?
Sorry, it only connect a water flow sensor.
@@digitenvictor1532 do you have any device which can connect more than one sensors?
Please tell me the function, may be we will design new one in the future. but now we have not the one you want. sorry!@@WeitangChen110
What if in display, it is showing "ERR" instead of temperature. what is wrong?
Don't connect to temp sensor, or the temperature sensor is damaged
how do I get my K value ? I have 4 and none are accurate. I've emailed support I've got zero support
Please tell me the model of flow sensor. in fact, you can ask for the manufacturer of flow sensor.
DIGITEN Victor Digiten FL-408
@@LokiGro The K value is 7.5, you can adjust it according to the accuracy of discharge.
DIGITEN Victor how Do I determine accuracy? If the water pressure changes will the k Value also need to be changed ? Thank your for responding I was loosing my mind
@@LokiGro If the water pressure changes, the accuracy will be changed, but the affect is small
is this suitable for 50ml per minutes?
Yes, it can monitor it. but the rate depend on the flow sensor.
What is the difference between this and the one in this video:
czcams.com/video/7WLoF_r4iBk/video.html