I look at you welding Terry and you make it look so easy but I must tell you the set-up for the first plates...even I didn`t like it. My arm got tired just looking at you....Well done my friend....CHEERS
Hi Terry,,Good to see your hanging in there,,, the slow work is everywhere in the world, so your not in the barb wire canoe paddling up stream alone there’s a lot of us in the same boat with you..regards Frank
Terry the news keeps saying we're booming but everyone I talk to says it's slow , ya think the news might be full of sh*t😅 I went to my steel store and soon found out what I bought for $20 in 2019 is $75 and told I should grab it before it goes higher 😬
I just talked to an oil trader and he said they won't drill for new oil because of Biden. Oil is twice as much as it was in 2019 but steel and labor are triple. They can't afford to drill. Pipe for casing is even more than that and has to come from China.
I usually do edge welds, lay it flat on the table and stick a block under to raise it up an inch or so then turn my torch sideways between my fingers and slide my hand across the table, got a wheelie seat off a tool truck gets me down low enough to be comfortable
Nice video.yea its all about being comfortable through your range of motion,and you're all about comfort,I envy your gigs,thanks for sharing your talents🤗😎🤗😎
that kinda looks like the clamp thing they use when pulling water well pipes they lock the pipe at every joint so they can unscrew the sections of pipe.
Nice job as always Terry, Mild Steel is just as good as any to weld except for the smoke and mill scale.I like how you have the fan pulling the smoke and not the shielding gas...many years of experience there boy...I can add to your welder shirt sayings but this is a family show lol!👍👍
Good to see a little Friday Gravy!!! Take care Terry!
That was all I had to do on Friday. 😂
I look at you welding Terry and you make it look so easy but I must tell you the set-up for the first plates...even I didn`t like it. My arm got tired just looking at you....Well done my friend....CHEERS
That's what I felt. My old arms don't like that anymore. 😂
One thing I have learned from watching you Terry, is the importance of proper jigs for welding efficiently. Thanks for sharing your expertise.
They do make life easier. Thanks George.
Hi Terry,,Good to see your hanging in there,,, the slow work is everywhere in the world, so your not in the barb wire canoe paddling up stream alone there’s a lot of us in the same boat with you..regards Frank
Thanks. For a while it was nice to have the extra time but now I'm getting bored.
I concur with Lloyd. Another great job.
Thanks. It was fun too.
They can always count on you Terry for a quality job every time.
I always try.
Nice as always, just bought a cheap tig welder, it will be a big learning experience.
Keep practicing. It will get to be natural after a while.
Terry the news keeps saying we're booming but everyone I talk to says it's slow , ya think the news might be full of sh*t😅 I went to my steel store and soon found out what I bought for $20 in 2019 is $75 and told I should grab it before it goes higher 😬
I just talked to an oil trader and he said they won't drill for new oil because of Biden. Oil is twice as much as it was in 2019 but steel and labor are triple. They can't afford to drill. Pipe for casing is even more than that and has to come from China.
I usually do edge welds, lay it flat on the table and stick a block under to raise it up an inch or so then turn my torch sideways between my fingers and slide my hand across the table, got a wheelie seat off a tool truck gets me down low enough to be comfortable
That would work.
Nice video.yea its all about being comfortable through your range of motion,and you're all about comfort,I envy your gigs,thanks for sharing your talents🤗😎🤗😎
Thank you for watching and the great comment.
Nice steady weld for a awkward position.
It was OK but my arms would have been tired if I didn't set it up a bit lower. Thanks.
Super nice work Terry ! .. ENJOYED
Thank you Shawn, stay well.
@@txsviking Working on it Terry , Thanks man!!
The MC is looking good. Never heard anyone complain about it being too hot to ride though. LOL
It's only to hot when stopped at a light. Then it's miserable 😅
that kinda looks like the clamp thing they use when pulling water well pipes they lock the pipe at every joint so they can unscrew the sections of pipe.
I think it is used for something very similar.
How's she goin'? Set up and being comfortable when you're working is key eh!! Another nice job. Take care!!
That it.
Well those were interesting pieces to be sure.
Very seldom do I get to work on mild steel. It was king of fun. Thanks Chris.
Great Video Terry :)
Thank you.
Nice job as always Terry, Mild Steel is just as good as any to weld except for the smoke and mill scale.I like how you have the fan pulling the smoke and not the shielding gas...many years of experience there boy...I can add to your welder shirt sayings but this is a family show lol!👍👍
Haha family show. 😂😂 Thanks buddy.
Gotta do just enough to make sure you dont forget what youre doin. Lol. Keep cool and healthy bud. Look like me weldin in shorts. Lol. 🤙🍺🌄
I always work in shorts and tee shirts in case I have to step outside.
Is the fan for the fumes, are they that harmful?
I don't like to breathe any smoke or fumes.
Love the shirt 🤣
I know right? My wife got it for me a few years ago. Thanks.
What filler rod did you use on that material?
ER70S-2 filler.
Thank you! Your videos are very educational! Glad I found your channel