Video není dostupné.
Omlouváme se.
Husqvarna Leaf Blower Carburetor Kit
Vložit
- čas přidán 9. 09. 2015
- This video provides step-by-step repair instructions for installing the carburetor repair kit on a Husqvarna leaf blower. The most common reasons for installing the kit are when the leaf blower won’t start or runs poorly.
Buy part #K21-WYA now: www.repairclin...
Additional leaf blower repair, troubleshooting tips, help finding your model number, and part replacement videos: www.repairclini...
All of the information in this carburetor repair kit installation video is applicable to following brands: Husqvarna
Tools used: needle nose pliers, T-27 Torx bit, phillips head screwdriver, flat head screwdriver
Buy part #326 now: www.repairclin...
Buy part #131CBTP now: www.repairclin...
Buy part #S144CB now: www.repairclin...
Buy part #P204CB now: www.repairclin...
Connect With Us!
plus.google.co...
/ repairclinic
/ repairclinic
/ repairclinic
Join our free VIP email list for discounts and money-saving tips: tinyurl.com/pnn...
Check out our blog: www.DIY.RepairC...
Don't forget to like and comment on this video, and subscribe to our channel!
This video was excellent. It gave me the nerve to tackle the carburetor rebuild on my own and save a bunch of $$$.
Thanks.
What a pain getting one of these things running..,
Two winters, with fuel left IN THE TANK. No problems. Then the third winter it decided to not rev. It took quite a while to figure out the whole problem.
Did all the "usual" maintenance tasks. CLean air filter, clean gas filter, clean exhaust spark arrestor. No good.
Carburetor Rebuild Kit. Partial success. The machine still bogs down when going past 50% throttle. After thinking about it, and viewing a video on how these venturi carbs work, I decided that one or more ports are clogged.
The ultimate cure was SEA FOAM, Marvel Miracle oil, and Husqvarna recommended fuel. Added 1 ounce of each to the gas (about a quart from the Husqvarna can)
At half throttle I was able to get my work done AND heat up the machine very hot. After running, pull out the fuel filter and drop it into a container of SEA FOAM and run it on HIGH throttle until the engine dies from lack of pure fuel.
Let it sit overnight. Fire it back up on gas in the morning. Several days of this, and it runs like a dream, all the way to full throttle.
A little trick to get it up in RPM is to take it as high as it will go before bogging down and "feathering" the throttle. This creates a dynamic in the carb that fills up all the chambers and keeps fuel flowing into the jets. While it is running at high RPM, it is flowing more cleaner through and dissolving gunk in the carb.
There may still be some gunk in the carb, but hopefully it should clear up if I SEA FOAM it every time I put it away..,
It took some work, but I didn't have to pay a shop for it.., :)
Thanks Brother!
4 days I been playing with mine new plug new gas filter cleaned air filter and just put new gaskets in carb. Same results its starts fine but when I give it throttle it stalls wtf. Will sea foam help this I never used it before
@@robertsuckfiel5716 Finally..I fixed mine..it's kinda sad...mine would run for 3 minutes then just bog down & stop...I replaced carb, fuel filter, gas lines, plug, air filter, cleaned gas tank & everything.....then I tried a different gas cap from my other hand held blower......ran PERFECT!...can't believe it was the gas cap...lol
@@Rick-be8pw are you kidding me if it's the gas cap I'm gonna cry. I'll try when I get home from work
Didn't work, going to a shop I've lost my patience. Thanks tho
First time carburetor rebuild experience, successful due to this most excellent instructional video. Thank you! My model, manufactured in 2014 however does not have the brass jet with the O ring. Why is that?
Mine didn't have the removable jet
At 3 minutes you show removing a main jet. My k21-wya doesn't have that removable jet, it's just blank there. Is there any concern with this?
I threw the cardboard gasket away. will it run without it
still the best on Howto.
what if the jet is clogged