Thank you for this video. both of my bumper caps were damaged, so I decided to replace both. I decided to add the fog lights this video was so helpful. Thank you
I have a 2008 2500HD Regency. I have watched hundreds of different content creators in an attempt to upgrade or fix carious parts of my vehicle. You are, without a doubt, the best instructor. You are very concise; you use many descriptions relating to position and orientation; and you go into great detail without skipping any steps. An idiot could follow your instructions and accomplish great things. Liked and subscribed!
Just finished this install on my 2010 silverado WT and my grey block was stuck underneath the fuse panel. I pryed one side out gently and it came out easy. Pushed my power lead in and you can see from the top of the grey block if its seated properly. I used a multi meter to test if the fog light harness had power and everything is fine. Definitely could not have done this without coming across this video. I salute you for posting it!!!
I just did this, along with installing new bumper & valance, & added fog lights to truck with none. - Loved the video. Very helpful. Much thanks. A couple things to add: When I tightened down one of the grounds the wiring on the neck under wrench turned & tore ~in half (is aftermarket, may be more fragile), so I backed out & put a big washer on top of the 3 grounds on that side (& did same on other side). Washer holds all in place nicely (video has washer there or bolt/washer combo). Be careful with fragile harness wiring. - 2nd: (this is mentioned in vid) After I took top off fuse box & finagled the big gray handles to remove the top black part, I had to use a LOT of force to remove mine, more than I thought, straight up. - 3rd: (not in vid) The small gray block underneath toward front that you put the wire into has (4) tiny gray over black tabs that have to be pushed back before the gray block will lift. I used (2) tiny screw drivers to remove one end then the other. It was a little challenge. - 4th: (reiterating what others have said) I had a hell of a time pushing in the side orange bar for the wire I'd put in the gray block. I didn't have any fat wires (yellow & black in vid), but found the slot by locating the smaller blue-green & green wires at one end. Thanks to the vid it's easy getting our wire into correct slot & feeling it hit bottom, but I couldn't push closed the orange side bar until I used a tiny screwdriver to carefully force our red wire down further & pushing it down much harder than comfortable. But that worked. Electrical wires: One minute you tear them just lightly putting on a bolt to secure them, next minute you're shoving them into a little slot.
When finished, I found the fog light on the side with the torn ground wire to be dimmer than the other. Word on the street is it's most likely to be that damaged grounding wire.
My wire colors were a bit different from yours but the new wire plugged into the same location as yours and it works great. Thanks for such a good detailed video.
Thank you very much you made this very understandable! The way it should be you didn't spend a lot of time talking about your truck. Thank you again looking forward to more videos. I've done a complete frame restoration on my 2011 Chevy Silverado started with a fuel pump replaced fuel pump cross members front and rear tire cross member rewrapped all my wires new cab mounts shocks and struts taking my time after work and on weekends this was one of my added touches I wanted to do. Bought this kit on Amazon thanks again.
This seems to be the most informative video I have seen concerning the install of the fog lights. I understand that this is for the stock style fog lights. However would you have any information where I could find a set of pigtails, that will plug into the new harness, for aftermarket lighting. Thank you for doing a great job with your explanation
Edit: see bottom but if having issues this might help: Ok did exactly as you have. Checked grounds. No power to lights? I have 15amp fuse for fogs in fuse box. Should I just tap off the fuse in the block?! UPDATE: Ok for those with same issue I didn’t push the power tap far enough into the grey block. You really got to push that in there. Now it works as it should!
@@thatsinglecabchevy1426 I got it to work! I updated my message, just so if people have same issue they can see why. In my case I wasn’t jamming that adapter in the grey block far enough! They work great now thank you!!!
I've tried multiple switches and mine won't work (bought this exact kit). If I jump the fuse the lights come on (no indicator). It seems as though I'm missing a solid orange wire from the switch harness (junkyard info) but I'm not sure where to connect it to on the other end. Any help appreciated. The video is great, it just seems as though i have the only gm on the planet with the fuse and relay but they aren't wired to the switch
Ordered the wire harness and light switch . I installed the lights, ran the wire harness was . BUT now when I turn them on I get static through the speakers listening to the radio ??
Not sure, I’ve only done the gas burners. Should be the same install, just double check the wiring diagram to ensure you’re in the correct block placement.
I did everything you did and I know it’s correct but my lights don’t work and everything is brand new. Any possible reasons? Checked the fuse and relay and everything is good. The light also pops up on the dash like it is turned on.
@@thatsinglecabchevy1426 so I just looked at this again. I think that new wire that is ran into the fuse box is not making connection with fuse above it. I can’t seem to push it any further. Any suggestion on that? Thank you for the help!
@@erikwyczalek Sounds like you just aren’t making contact at the upper fuse box section and the lower fuse bank. Check for proper seating on the fuse bank, then look at the connection prongs that connect the upper fuse box to the lower bank. May have gotten bent. ..I’ve seen where the plastic divider tabs have bent/broken and not allowed the upper section of the fuse box to sit all the way onto the lower banks. Is your fuse box setting and locking into place properly?
@@thatsinglecabchevy1426Thank you for the help. I will go check all of that to make sure. My guess is something got bend and isn’t making good connection.
I’m having the same problem. Everything connected as in the video but they don’t seem to work. Light indicator on the dash also lights up but the fog lights won’t. Any suggestions on what it could be and what u did to make it work? Thanks in advance 🫡
I put the new bumper ends on with the lights wired the wiring harness when it came to installing the wire to the fuse box mine is different I don't have that little block that you have! It's a 2011 Chevy Silverado LS. Help!
Most likely your dome light switch is on. It’s the small knob in the center of the switch. Press it and it pops out. Turn it counter clockwise to turn off the dome light.
The only thing I can think of is my block is attached to the bottom of the fuse box that you're lifting out. It's not on the bottom like I see in your video
Hey I have a question on the fuze box we’re the fog light to install I have a fuse that says 9831 I don’t know if I should install on that one or I have to buy a fues
@@fuckthehaters6069 look under your fuse box lid. There should be a diagram that shows your fog lights / relay location. Fuse for your fog lights should be a 15amp fuse in the number 28 fuse location.
They go behind the bumper corner bracket. You’ll have to remove the three bolts that hold it in. The fog light buckets have three mounting points. You’ll need to install the buckets at a 45 degree side angle. Angle the single mounting hole first, then the side with two holes will drop into place.
@@fuckthehaters6069 Go to my HD Conversation video. At 7:18 it shows the bracket and fog light buckets installed. Here’s the video link: czcams.com/video/bGbx7IiPBjo/video.html
@@fuckthehaters6069 You will need that corner metal bracket to install the fog light buckets. Two screws go through this bracket and into the back of your fog light buckets.
@@ArcFireX When you said “housing,” I thought you were talking about the buckets the fog lights sit in. Lol. I have OEM buckets not fog lights. The Fog lights are doing good so far. I’ve have them for about 5 months.
I know some guys will not remove the lower panel to save time, but this is the recommended way for removal. There is a flange on the bezel that can break or scratch your lower panel if it’s not removed. It also gives you room so that you can pull straight back on the bezel. Some guys will break their retaining tabs/clips, because they pull the bezel at an angle - because the lower panel is in the way. Just don’t want anyone mad at me because they f***ed something up. Lol
My silverado is a 14 I'm doing the same mod .my question is will it work the same if I install wire in same position. The fuse is there but no place for fog light relay.
I don’t have a front right block. I had a back right block( if your in the driver seat) it’s a single cab wt. not only that my block has wires in different locations.
In this video you did it behind the yellow and next to the two greens. On my block there isn’t a yellow but the two green spot has one yellow and one green.
@@thatsinglecabchevy1426 yes and no. I have the parts you have. When I opened my fuse box I didn’t see the little boxes like in your video, they were attached to the bottom of the fuse panel instead of resting on the top of the other area. I did exactly like you said but they don’t power on. So ima get a power probe and see if it’s getting power to try and track what’s wrong
@@thatsinglecabchevy1426 getting the connection in was hard at first. The little red clips wouldn’t want to slide back in with the wire there. But I pushed it in and forward and then it was able to squeeze back in but no power
Thank you for this video. both of my bumper caps were damaged, so I decided to replace both. I decided to add the fog lights this video was so helpful. Thank you
I have a 2008 2500HD Regency. I have watched hundreds of different content creators in an attempt to upgrade or fix carious parts of my vehicle. You are, without a doubt, the best instructor. You are very concise; you use many descriptions relating to position and orientation; and you go into great detail without skipping any steps. An idiot could follow your instructions and accomplish great things. Liked and subscribed!
Thank you. ☠️
If every tutorial on CZcams are as detailed as yours, there would be 100 times more DIYers out there...
Appreciate you, ☠️👊🏼
Just finished this install on my 2010 silverado WT and my grey block was stuck underneath the fuse panel. I pryed one side out gently and it came out easy. Pushed my power lead in and you can see from the top of the grey block if its seated properly. I used a multi meter to test if the fog light harness had power and everything is fine. Definitely could not have done this without coming across this video. I salute you for posting it!!!
I just did this, along with installing new bumper & valance, & added fog lights to truck with none. - Loved the video. Very helpful. Much thanks. A couple things to add: When I tightened down one of the grounds the wiring on the neck under wrench turned & tore ~in half (is aftermarket, may be more fragile), so I backed out & put a big washer on top of the 3 grounds on that side (& did same on other side). Washer holds all in place nicely (video has washer there or bolt/washer combo). Be careful with fragile harness wiring. - 2nd: (this is mentioned in vid) After I took top off fuse box & finagled the big gray handles to remove the top black part, I had to use a LOT of force to remove mine, more than I thought, straight up. - 3rd: (not in vid) The small gray block underneath toward front that you put the wire into has (4) tiny gray over black tabs that have to be pushed back before the gray block will lift. I used (2) tiny screw drivers to remove one end then the other. It was a little challenge. - 4th: (reiterating what others have said) I had a hell of a time pushing in the side orange bar for the wire I'd put in the gray block. I didn't have any fat wires (yellow & black in vid), but found the slot by locating the smaller blue-green & green wires at one end. Thanks to the vid it's easy getting our wire into correct slot & feeling it hit bottom, but I couldn't push closed the orange side bar until I used a tiny screwdriver to carefully force our red wire down further & pushing it down much harder than comfortable. But that worked. Electrical wires: One minute you tear them just lightly putting on a bolt to secure them, next minute you're shoving them into a little slot.
When finished, I found the fog light on the side with the torn ground wire to be dimmer than the other. Word on the street is it's most likely to be that damaged grounding wire.
Did you have to replace the entire bumper? I heard and read one might only need the end caps replaced. Thanks for the additional info on wiring.
Extremely detailed need more videos like this !!
Appreciate it!
My wire colors were a bit different from yours but the new wire plugged into the same location as yours and it works great. Thanks for such a good detailed video.
Glad this helped. 💀👊🏼
Best installation video I've seen in a while
Much appreciated 💀👊🏼
Thank you very much you made this very understandable! The way it should be you didn't spend a lot of time talking about your truck. Thank you again looking forward to more videos. I've done a complete frame restoration on my 2011 Chevy Silverado started with a fuel pump replaced fuel pump cross members front and rear tire cross member rewrapped all my wires new cab mounts shocks and struts taking my time after work and on weekends this was one of my added touches I wanted to do. Bought this kit on Amazon thanks again.
Really appreciate you taking the time to give positive feedback. I love these trucks, brother - and glad to hear you’re resurrecting your 2011. 💀👊🏼
This seems to be the most informative video I have seen concerning the install of the fog lights. I understand that this is for the stock style fog lights. However would you have any information where I could find a set of pigtails, that will plug into the new harness, for aftermarket lighting. Thank you for doing a great job with your explanation
Very good video and explained perfectly thanks
Thanks ☠️👊🏼
Awesome. Thank you so much for making this vid.
On the hooke road bumbers, there isnt a power lead, but 2 short positive and negative wires, do you connect those to the ground wire?
Very helpful. Thank you for your time and knowledge.
Glad to help. Thank you.
Edit: see bottom but if having issues this might help:
Ok did exactly as you have. Checked grounds. No power to lights? I have 15amp fuse for fogs in fuse box.
Should I just tap off the fuse in the block?!
UPDATE: Ok for those with same issue I didn’t push the power tap far enough into the grey block. You really got to push that in there. Now it works as it should!
Do you have the relay for the fog lights installed?
@@thatsinglecabchevy1426
I got it to work! I updated my message, just so if people have same issue they can see why. In my case I wasn’t jamming that adapter in the grey block far enough! They work great now thank you!!!
Excellent write up!!
Appreciate it! 👊🏼
I have never watched such a simple and helpful tutorial, you earned yourself a new subscriber! Keep it up
Appreciate it 💀👊🏼
New sub very clear and helpful/ detailed
Great video! Very helpful. Thanks
Thanks 💀🤙🏼
this was very helpful thank you sir👍🏼
Thank you
I ssume the process is the same for gmc Sierra
,correct?
Thanks 🙏
Yw 👊🏼
I've tried multiple switches and mine won't work (bought this exact kit). If I jump the fuse the lights come on (no indicator). It seems as though I'm missing a solid orange wire from the switch harness (junkyard info) but I'm not sure where to connect it to on the other end. Any help appreciated. The video is great, it just seems as though i have the only gm on the planet with the fuse and relay but they aren't wired to the switch
Did you check to see if your relay is bad? If it’s good, I’d look at a wiring diagram for your year to make sure you’ve got the correct harness.
you never showed where the plugs actually plug into? they just plug into the fogs?
Yes, they plug directly into the back of the fog lights.
Thank you! What is the part number of the required harness?
Links for everything are listed in the description box below. 👊🏼
Is it normal that the switch inside the truck doesn’t illuminate?
Not normal at all. Should be working. Make sure your illumination isn’t turned down. But even with that, it would be a low light not no light.
Ordered the wire harness and light switch .
I installed the lights, ran the wire harness was . BUT now when I turn them on I get static through the speakers listening to the radio ??
How do you install the fog light housing ?
Where does the red wire attach on the block for a diesel. I noticed that you only showed this for a gas burner.
Not sure, I’ve only done the gas burners. Should be the same install, just double check the wiring diagram to ensure you’re in the correct block placement.
What’s the part number for the fog light bracket?, that’s the last part I need
What year/ model bumper do you have?
Where can I get the fog lights and anything else I need ? I have the 2500 bumper hd
The links are down in the description box.
There are 2 different wiring diagrams. 1 for gas and 1 for diesel
I did everything you did and I know it’s correct but my lights don’t work and everything is brand new. Any possible reasons? Checked the fuse and relay and everything is good. The light also pops up on the dash like it is turned on.
Double check your fog light grounds, and make sure you’ve got power in the new wire lead from the fuse box.
@@thatsinglecabchevy1426 so I just looked at this again. I think that new wire that is ran into the fuse box is not making connection with fuse above it. I can’t seem to push it any further. Any suggestion on that? Thank you for the help!
@@erikwyczalek Sounds like you just aren’t making contact at the upper fuse box section and the lower fuse bank. Check for proper seating on the fuse bank, then look at the connection prongs that connect the upper fuse box to the lower bank. May have gotten bent.
..I’ve seen where the plastic divider tabs have bent/broken and not allowed the upper section of the fuse box to sit all the way onto the lower banks. Is your fuse box setting and locking into place properly?
@@thatsinglecabchevy1426Thank you for the help. I will go check all of that to make sure. My guess is something got bend and isn’t making good connection.
I’m having the same problem. Everything connected as in the video but they don’t seem to work. Light indicator on the dash also lights up but the fog lights won’t. Any suggestions on what it could be and what u did to make it work? Thanks in advance 🫡
I put the new bumper ends on with the lights wired the wiring harness when it came to installing the wire to the fuse box mine is different I don't have that little block that you have! It's a 2011 Chevy Silverado LS. Help!
Should be the same? If you have a picture of it you can send it to my Facebook facebook.com/thatsinglecabchevy?mibextid=LQQJ4d
What do you connect the plastic to I don’t see anything under the bunper
The fog light bezel slides under the flange on the inner bumper and two 8m screws fasten it through the backside of the outer corner bracket.
My dome lights seem to stay on once I installed the new switch
Most likely your dome light switch is on. It’s the small knob in the center of the switch. Press it and it pops out. Turn it counter clockwise to turn off the dome light.
The only thing I can think of is my block is attached to the bottom of the fuse box that you're lifting out. It's not on the bottom like I see in your video
Should be the same on all 07-13 Silverados. Do you have the fuse and relay for the fog lights in your fuse box?
I followed your instructions but foglights don't come on at all
Did you get it to work?
Do I buy 1500 bezels or 2500 ??
What bumper do you have?
Hey I have a question on the fuze box we’re the fog light to install I have a fuse that says 9831 I don’t know if I should install on that one or I have to buy a fues
Or can I buy a fues and put it some were els
@@fuckthehaters6069 look under your fuse box lid. There should be a diagram that shows your fog lights / relay location. Fuse for your fog lights should be a 15amp fuse in the number 28 fuse location.
@@thatsinglecabchevy1426 I did but it has a fuse there already but it’s not the same number of the fuse
How u put the fog light housing on the bumper
They go behind the bumper corner bracket. You’ll have to remove the three bolts that hold it in. The fog light buckets have three mounting points. You’ll need to install the buckets at a 45 degree side angle. Angle the single mounting hole first, then the side with two holes will drop into place.
Ok thanks
Do I have to buy extra bracket for the fog light housing or just like that because I only have the 3 that came with it
@@fuckthehaters6069 Go to my HD Conversation video. At 7:18 it shows the bracket and fog light buckets installed. Here’s the video link:
czcams.com/video/bGbx7IiPBjo/video.html
@@fuckthehaters6069 You will need that corner metal bracket to install the fog light buckets. Two screws go through this bracket and into the back of your fog light buckets.
You have a tiktok???
How are the fog light housing holding up?
Great. They are OEM.
@@thatsinglecabchevy1426 oem? The Amazon link has a lot of negative reviews about the tabs breaking and fitting loose
@@ArcFireX When you said “housing,” I thought you were talking about the buckets the fog lights sit in. Lol. I have OEM buckets not fog lights.
The Fog lights are doing good so far. I’ve have them for about 5 months.
Why did you remove the lower interior panel and side panel?
I know some guys will not remove the lower panel to save time, but this is the recommended way for removal.
There is a flange on the bezel that can break or scratch your lower panel if it’s not removed. It also gives you room so that you can pull straight back on the bezel. Some guys will break their retaining tabs/clips, because they pull the bezel at an angle - because the lower panel is in the way. Just don’t want anyone mad at me because they f***ed something up. Lol
My silverado is a 14 I'm doing the same mod .my question is will it work the same if I install wire in same position. The fuse is there but no place for fog light relay.
If you have the fuse you should have the relay.
Can you reply quickly? I’m in the middle of the install and my wiring is not the same as yours
I don’t have a front right block. I had a back right block( if your in the driver seat) it’s a single cab wt. not only that my block has wires in different locations.
In this video you did it behind the yellow and next to the two greens. On my block there isn’t a yellow but the two green spot has one yellow and one green.
Were you able to get it?
@@thatsinglecabchevy1426 yes and no. I have the parts you have. When I opened my fuse box I didn’t see the little boxes like in your video, they were attached to the bottom of the fuse panel instead of resting on the top of the other area. I did exactly like you said but they don’t power on.
So ima get a power probe and see if it’s getting power to try and track what’s wrong
@@thatsinglecabchevy1426 getting the connection in was hard at first. The little red clips wouldn’t want to slide back in with the wire there. But I pushed it in and forward and then it was able to squeeze back in but no power