How to Setup XH-W3001 Temperature Controller (Controlling a Fan using Digital Thermostat)

Title: How to setup XH-W3001 Temperature Controller
On this project I show you how to connect and setup a XH-W3001 Temperature controller or a Digital Thermostat to control a cooling fan.
I used this project to cool down and maintain the temperature of my solar inverter in order not to overheat.
But this project can also be use in other application like for example Incubator, etc...
Using a XH-W3001 I able to control my Fan to start at 45 deg.C and stop at 38 deg.C.
XH-W300 digital thermostat is very cheap and you can purchase it in online store.
Warning: This video is for informational purposes only. Do not attempt any wiring of any kind if you lack the knowledge and understanding required.

[@mafiacarzz]

Thank you so much Sir, you presented it amazingly.I really understood your demonstration and it was very easy to understand. Once again Thank you very much.

[@matanissler]

great tutorial! It's really useful for my DIY project!

[@russelldavis3435]

Great video... Thank you so much for taking the time to make this video... My switch came without instructions.. Thank you

[@winneowen9328]

Pretty good video. Cool presentation :-)

[@alvingarcia6476]

Thanks Sir, presented very well, napakadali sundan..

[@rodBACON]

Your welcome Sir Alvin and thanks for your appreciation

[@jeffchannel8402]

Nice presentation,sir.easy to understand.

[@rodBACON]

Thanks for appreciating my video sir Jeffrey...

[@rbay8487]

Just perfect!!!

[@ccv3237]

Beautifully well presented animation, congratulations! Could you please tell us the name of the animation program you used?

[@agusrakhmat6721]

Thank you. Very useful

[@rodBACON]

Glad it was helpful! Agus thanks for the good feedback...

[@agusrakhmat6721]

Very useful

[@madalachandrasekhar733]

Dear brother...which model shall i use for room heater of 2000 wats...i want the temperature at 25 deg ..please suggest me the best for this purpose...thank you

[@rolandobalbag7033]

Thanks idol eto hinahanap ko..

[@rodBACON]

Your welcome Sir Rolando

[@mariusstan352]

good job !

[@rodBACON]

Thanks!

[@agrogardening]

good information for me

[@rodBACON]

Thanks and welcome...

[@brucehutcheson5371]

When I powered m X-HW-3001 on, its immediately shows a temperature of 56 degrees. Well that isn't Fahrenheit or Celcius as its about 20 C or 74 F here. Oh well.

[@marlonbernales7706]

Gud day sir...Saan mo na bili yang temp.controller.. xh- w3001? Salamat po sa tutorial sir...madami po ako natutunan sa mga vlog mo.

[@innocentmamba6788]

Thank you

[@rodBACON]

You're welcome Innocent Mamba

[@user-yl8cm5rq2l]

Which software do you used to make this animation tutorial?

[@rodBACON]

Adobe Photoshop and Adobe After Effects

[@kramyu3391]

Ang set up ng fan blow air out from fins or blow air into finals?

[@rodBACON]

yung set up ko Sir Mark is Blowing air into fins...

[@aljamco6361]

Ayos sir.. Hi-tech..

[@rodBACON]

SAlamat Al Jamco... GOD Bless and Be Safe...

[@didocasablancas]

Hi i have a question and hopefully you can answer it. Can i make the temperature controller using light bulb n cooling fan?
Meaning here is, if the temperature gets above 39.5. The light bulb will turn off and the cooling fan turn on. Then if the temperature dropped to 37.0 , the fan will turn off and the light bulb turn on, is it posible?