If you have a front load washer with a pump filter, your pump filter may become clogged with particles overtime. This video will demonstrate how to clean your pump filter. Learn more at www.geappliance....
I can't believe it. The clothes started to get wetter and wetter after the spin cycle and I didn't know why. The machine started throwing no drain codes tonight. Found this video and then a bunch of really nasty lint and some old wrappers and stuff in the filter. Mine is a Kenmore but this video still fit the bill. Thanks GE for the customer support!
Thanks so much for this! We've been using a Laundromat for weeks because we thought the repairs were going to cost a fortune. Instead, I managed to removed the sock that had somehow wedged its way in there and it didn't cost me a cent. Thanks again!
This video saved our butts! I kept calling around asking for quotes for appliance repair when our washer stopped working and the prices were a bit outrageous for a repair shop to simply check what the problem was, not even actually fix it. Started browsing, found this video, and followed these steps to fix it right away. Thanks for posting!
Our system wasn't draining properly, after some Googling I found this video, we opened the filter pump and there was a brick of fabric and dog hair and other crap in there... it was super clogged, had no idea that we had to empty this. We almost called in a repair guy, but this fixed the problem. Thanks!
Steven Tyler just pull off the drain pipe and BLOW LIKE HELL!!! I used a clean wash rag so my lips didn't touch that nasty hose. After a few weeks of "blowing" treatments, my duet drains fine. But you have to make it "gurgle" . I'm sure a shopvac in reverse will work better. Blows the crap back and breaks it up to drain, it's usually just clunked up lint. Try air compression before buying expensive part. Trust me.
My wife has had her machine for a year now and asked me if I would help her to check the drain filter. We're in our 70's and what is easy to who ever designed and built is not so easy to an elderly couple even with50-years of D.I.Y. experience. #1.... The machine in the video is installed close to an inch higher than ours. This made all steps in the removal that much more difficult, even to the point of trying to get a small drain pan in place. Perhaps the install directions provided to company's that sell your products should come with minimum installation height requirements. #2 ..... If it hadn't been for this video we never would have figured out how to pull the drain funnel down. My wife was going on your written manual instructions until she got frustrated and came to me for help. My wife does not use a computer so for those in America still trying to live without computers or internet it might be beneficial to clarify your written instructions. #3..... The pump filter was still factory tightened and my wife found it impossible to loosen. I myself spent another 3-5 minutes trying to turn it counter clockwise until it finally broke loose. However, the space that you have allowed is so small that I ended up scraping my hand in the process. Another inch in width and length would greatly facilitate access.
Thank you thank you thank you. Because of your video I was able to drain my front loading Kenmore (nearly 10 years old) and clean the filter (every 2 months? Yikes) I removed over a gallon of standing water, and the filter was full of hair from me, and two dogs. I kept thinking "this will never work" It worked!!
Hi, Monique - Thank you for your inquiry. I am happy to direct you. If your washer does not have an easily accessible pump, without the removable panel, service may be needed. Our GE Consumer Service technicians are well equipped to resolve an issue such as this. Appointments may be scheduled on our GE Appliances website under the support tab. Thanks again for reaching out to us.
This video was most helpful--thank you! I'm hoping that solves the problem, and I'm confidant it will (haven't run a load yet). Like others here, I had a ton of dog hair in my filter, after washing their blankets. I was winding up with wet clothes at the end of the wash cycle and a drain cycle that went on forever, presumably putting more wear on the pump. A couple of notes about my cleanup: I had a hard time turning the filter counterclockwise to remove it; a few light taps with a hammer got it unstuck. Since I had run a few loads after the clog occurred, there was about a gallon of water behind the clog. Even though I had a bucket set up underneath (my machine is on a pedestal), it ran into the pedestal drawer handle and into the drawer below (fortunately only had tools under there). I would suggest that if you have a pedestal, construct a way to direct the water from the pump filter compartment into a large container so that it bypasses the pedestal drawer. A piece of old tubing or even a dustpan would do it. Because my pedestal drawer can't be opened all the way due to being in a tight space, I couldn't pull it out to dump the spilled water. I used a bulb baster to remove the bulk of it and then sopped the rest up with a rag. BTW, the water in the video was a lot cleaner than what you might find in your machine!
Thanks a million to everyone who takes the time to post money saving tips on this site, our Frigidaire front loading washer wasn't going into the final rinse and spin cycle and the problem was that the coin catcher was preventing our washer from going to the final rinse and spin cycle, we found the coin catcher full of gunk and coins just like the video shows, thanks to all who share their expertise and it goes to show that all people aren't greedy like some and don't mind sharing what they know, much love to you all.
Sir Hugh Barst, so glad that this video was helpful! Those little things have a way of making trouble for any washer! Thanks for your comments! - Sheree with GE
Hi, Rachel Spies. Thanks for reaching out to us. Please take a look at your drain hose to ensure it is properly installed and not kinked or crimped. Also, make sure the drain in the household plumbing is not clogged. Hope this helps!
So glad you have a reference like this available here on you tube! So useful and convenient (no idea where my manual is at this time!) finding your info online was so very helpful! Thank you!
We are so happy to hear this video helped you! Please feel free to send us your model number and we will be happy to send you a manual if you'd like one. www.geappliances.com/ge/service-and-support/contact.htm?icid=GEARtopnav-contact JW
Thank you, I put a paddling pool under mine help my hand so it didn't drip down then opened it very quick so all the water shot out, do not open it quick straight away if you have a small water catcher it comes out so fast x
Thank you so much . My Samsung Washing Machine was giving "sod" error code. It was also taking too long for the complete wash. This is because a lot of dirt had got stuck in the pump filter. This Video helped a lot. :-) :-)
Hey there Marijo! While we do recommend that you follow the instructions from your manufacturer and for your particular model (as washers can differ both by different brands and different models), we’re certainly glad our video was helpful for you. We’re happy to assist however we can, and you’re always welcome to reach out here or over our GE Appliances social media if you have any concerns or questions. We’re wishing you all the best! -SG
You’re very welcome, Marijo - we’re glad we could help! Again, we’re always happy to assist if you have any other concerns or questions. Best wishes! -SG
My front loader has an issue with a queen size blanket keeps saying load rebalance, Put 1 pair of carhart overalls in does the same a load of bath towels will also make it go into rebalance mode. Never had a washer with so many problems. For being new this washer sure has issues, cleaned all filters leveled washer and rechecked several times manually rebaleance loads same issue. Never had a washer with this issue before!!!
Hi Hugh, We're deeply sorry to hear that your washer is having so many issues with balancing and understand how upsetting this must be. We recommend disconnecting power for a few minutes then restoring power to see if that solves the problem. If that doesn't work, then we would recommend service. You can schedule an appointment by calling 1-800-432-2737 or schedule online at spklr.io/6051YaYx. All the best. -MH
This pump filter is so much better designed than mine. Once I stop renting I'm definitely going to have to find a filter this practical! I think GE sells in the UK?
Thank you for your feedback, Ryan. We're glad this video helped, and hope future videos will be of assistance to you as well. Thanks for choosing GE Appliances! -NC
Update to previous comment. Perhaps a warning about the smell of the water coming out! Wow! ;-) I hadn't cleaned out that filter in the almost 7 years of owning our washer, and it was pretty nasty. Definitely putting a regular cleaning of that trap on my home maintenance schedule! Again though, thanks for the video. It did the job!
Thanks for this video...this video helped me when the washing machine was not draining and leaving giant pools of water across the floor...I removed the pump and with a pair of grips to loosen the hose clip,removed the hose to the filter...I found inside several metal bracings that go into the cup surrounds of bra`s and hairclips...also hair bands etc...those with teenage girls,beware !!!
Hi, Carol Pedley. Thank you for your post. We regret we do not have information on the Whirlpool brand. You may want to reach out to their company website for further direction. We are always happy to help if you have any questions on GE appliances or products!
Sorry for the delayed response Jamie! If you are still having issues, check out this link and see if it helps products.geappliances.com/appliance/gea-support-search-content?contentId=17398
Found a dryer sheet caught in there. a TON of water was leaking when turning the filter..no way to catch the water so i just kept a few towels there . I see now why it smelled a little "sewery".. Hoping that fixes the error We've been getting lately .Thank you for the vid!
Hi Anto - Thanks for your post. I’m sorry for any issue you are experiencing with your washer. You should not have to drain the filter out after each use. If you have not yet done so, please review our video, “Front Load Washer Out of Balance”, for some extra tips. Please let us know if further assistance is needed. Thanks, Jill with GE
Hi, trickshots2t. We’re happy to help. Please take a look on our GE Appliances website under our “Support” tab. Here you will find some helpful tips under “Frequently Asked Questions”, “What do I do if my washer is leaking water?” We hope this will offer resolution to your issue.
I have opened it up and yes there was some money in there. Took it out, put the filter back on and pressed start again but it still stops and the clean pump light still comes back on.?? What else do I do. Thankyou
I have a GE Front Loader Model GFWR4805F0MC, that also likes to stop mid cycle. I found a leaf inside my drain pump housing. The washer now pauses at 37 min during a normal wash cycle. I restarted it. It started to drain at 35 minutes. Good news is the machine is not pausing numerous times like before. I believe it was doing it 3 times per load. Does anyone have any other ideas what I can look for?
Thank to for this video it was very helpful. Did anyone else notice the water that was released to have a very bad smell? Also I can’t seem to get the filter door back on, it becomes loose from the bottom. Any ideas?
Hello, my front door washing machine drain pump run without laod (makes griding noise) however, when i want to drain water through it, it won't run at all. Do you think the pump is faulty ?
Hello! We're sorry you're having problems with your washer's drain pump. It's possible the drain hose may be kinked or clogged, or the washer pump filter may be clogged. For the best help, we recommend viewing our support article here: spklr.io/6052lMnk. If these suggestions do not help to resolve the situation, please schedule a repair service appointment by calling 1-800-432-2737 or online here: spklr.io/6053lMnZ. We hope this helps! We're always here if you need anything. Take care, SH
Not so easy 🥵 rubber seal doesn’t sit properly. It takes me several tries and a floor full of water until it is properly seated to not leak. Horrible design.
We regret to hear you had some trouble and hope it has since been resolved. If we can help further please feel free to send us a PM/DM on Instagram or Facebook page with the model and serial number on your unit. We are happy to help.
Hi, Meagan! It's true, things like this always look easier in the video. We have a helpful article here: spklr.io/6051Yi1b We recommend making sure the filter has been screwed back in straight and is not crooked. If you continue to have trouble, please send us the model number of your washer in a DM on Facebook or Twitter. - JB
Quick question, the pump filter access door won’t come loose! I’m using a screw driver, but regardless of how I twist, wiggle or pull it just won’t come off! What should I do?
Oh my washer is next level. At the middle of the drain pipe thats where everything stucks at so i need to open the whole washers cover and unscrew all the pipes to get these out deep inside
I have a GE front loading 8 cycle heavy duty Deluxe quiet machine. Don't know the model. And I'm curious since I have a leak at the front left hand side that it might be something like this. But I do not have that small pump door. There is panel that goes across the bottom of the machine probably a foot tall. Is this something I would remove in order to find a filter pump?
We'd be happy to look into this for you. Please provide your model number, so we can better assist. Instructions for locating this number can be found here: spklr.io/6052sTtE
Hi. I have the LG steam front load washer that is throwing a "check filter not draining" error just before the spin cycle.If I press pause then play button it will continue on with the cycle until the final spin where it will throw the error again.I do the same thing (pause, play) and it will finish off to the end of the wash cycle. The filter was cleaned out and I checked the drain line (watched it drain into the sink). I'm thinking that mechanically the pump is fine but electrically it may not be. Or does this sound like more of a circuit board issue? Any help is appreciated.Thanks.
Hi we have a aproximately 2009 front loader GE that 4x now has leaked from the back some how underneath. The water is very foul smelling like sewer water. It happened right at the beginning of the cycle. What could be the problem and the repair cost?
So if I have to drain my washer from the front after almost every single wash, what is the issue? Drain pump? If I don’t empty it then my clothes start to smell musty. Also….is there a way to put a hose inside the front hole and leave it open all the time to drain from the hose into the drain in our floor? Help!
If I drained all of the water in my washer and it started spinning and working again the next load and it pauses and doesn’t drain on the next load what should I do?
Hi Erica, Thanks for reaching out. Sorry to hear about your washer leaking, we're sure this would be frustrating. If you've not done so already, take a look at the following article to see if it helps matters: spklr.io/6056cbqi If you continue to have leaking issues we'd recommend reaching out to our service team, here: spklr.io/6057cbqc Hope this is helpful for you. We're here if you've got questions or concerns in the future. -MS
Hi there, We appreciate you choosing GE Appliances and would love to help. For the best assistance, we recommend scheduling service with a verified GE Appliances technician. You can schedule service by calling 1-800-432-2737. We're confident they will fix your unit in no time. All the best. -SH
Having a hard time putting filter tray back. It keeps turning and turning doesnt lock. Washed a load and water spewed out everywhere and of course our warranty has expired
Hi Terry, Thanks for reaching out. Sorry to hear about the pump filter issues you've had here. If you're still experiencing difficulty with your machine, send us a PM on Facebook or a DM on Twitter/Instagram with your complete model and serial numbers. We'd like to review further for you. If you need help finding your model and serial numbers, you can click here: spklr.io/6055lM5d -MS
Hi Anita - thank you for reaching out to us. If you are experiencing the error code CLrFLtr on your washing machine, please see page 29 of your Owner's Manual for additional troubleshooting tips. We hope this helps! Thanks for choosing GE Appliances! -NC
We’d be glad to assist with your concern! Can you please clarify the model number of the washer, here or with a private message over our social media (such as Facebook or Instagram)? With that information, we can certainly look into this further.
Hello-Thank you for reaching out to us. We are sorry to hear you are having some concerns with your filter unit and would like to help. Could you please send us a private message with your model and serial number? Look forward to hearing back from you. All the best.- DM
Copy and paste this troubleshooting link in your browser. spklr.io/6059oQif We know you said the pump filter is screwed in completely, however that could still be the cause of the leak. Unscrew the filter and then slowly tighten it and see if that helps. If it was put back on crooked, it could still leak. If you still have leaking issues, please reach out to GE Consumer Service by calling 1-800-432-2737.
I’m trying to figure out what could be causing a HORRIBLE odor from my GE profile washer. I’ve ran NUMEROUS basket clean cycles with bleach in the prewash like instructed by washer prompts and 5 cycles using afresh tablets but it’s not improved at all. It’s stinking up the entire house and even neighbors can smell it! It’s HORRIBLE. I keep the door open after washes and take clothes out right away. I did have the boot seal replaced but it appears to be sealed properly.. what else could be causing this and what can I do to resolve??? Please help!
Hello, Thank you for reaching out to us. We're sorry to hear you are experiencing an odor from your washer. We understand how problematic that would be, and we'd love to help. We recommend cleaning the pump filter if possible. Due to the design of the front-load washer, it is sometimes possible for small items to pass to the pump. This can restrict the draining process and may also contribute to odors. On most models, the pump filter is easily accessible for cleaning. You can view your unit's owner's manual on our GE Appliances website by searching the model number. Below are links that provide more information on the causes and solutions to address odor issues: Front load washer: spklr.io/6057W8PR. Top load washer: spklr.io/6058W8Pr. We hope this helps! Take care, SH
Hello-Thank you for reaching out to us. We would be happy to help! Could you please send us a private message with your model and serial number that way we can research this further for you? We look forward to hearing from you. Sincerely-DM
Hi, we're sorry to hear you lost the drain plug, but we'd be happy to help find a replacement. Could you please reply with the model number of your appliance? Thanks. -SK
Hi, because your washer was made by RCA, we suggest looking on the manufacturer's site for information on replacement parts. Thanks for reaching out to us, and have a great day. -SK
sounds silly but raise it a little off the ground and put a pot with boiling water under. let it sit for a couple minutes and that should maybe loosen it
We would like to know a little more. Do you mind sending us a PM/DM on our Facebook or Instagram page with the model and serial number of your appliance, and more details? If you need help locating the model please see the link here- spklr.io/6055SaQl
Yep leaving my Maytag for GE! GE doesn't force you like Maytag to take off the top of your washer, then the front panel, then the rubber seal, then the bottom screw JUST to do what she has shown here you an do in 5 minutes! Insane on MAYTAG and will be leaving them bc of their engineering insanity!
Our GE WCVH640J1WW starts to fill with water for about 30 seconds and then starts draining for a few minutes even after the water is gone and then just sits there. I knew about the access door on the front but didn't realize it was a filter, I thought it was just a drain. I removed the filter and cleaned lint and 2 pennies out of it and put it back in but still no luck. Water starts to fill for about 30 seconds, then drains for a few minutes and then just sits there doing nothing. Any ideas?
Reading from the comments below regarding cleaning the pump after use, my washer doesn't seems to be out of balance but I have to clean it after use because of water hold up and it starts to smell with in a day. Any suggestions or advice on how to fix it?
+Jen Cruz Hi Jen, it is possible for odor to occur inside the washer tub over time. Using the appropriate amount of detergent with each load and using HE detergent can help. GE recommends cleaning the washer tub once per month to keep the wash basket fresh and clean. For models with a BasketClean cycle:Use the BasketClean cycle and 1 cup of bleach or a commercially available product manufactured for this purpose. GE recommends Tide Washing Machine Cleaner for best results. Repeat if necessary. For models without a BasketClean cycle:Run a large Heavy/Cotton wash cycle with no items in the wash basket and 1 cup of bleach or a commercially available product manufactured for this purpose. GE recommends Tide Washing Machine Cleaner for best results. Repeat if necessary. Tide Washing Machine Cleaner is available locally at most grocery and retails stores.
I'm desperate and in need of help from anybody who has had the problem I've got with the lint filter lid. The lid itself will not screw on properly, it's a little crooked. I've checked the grooves for any damage and lint, but it's in mint condition. It simply won't screw on right, which causes water to leak from it. Anyone had this problem as well? It's a Matsui machine for reference
Hey there - We're sorry to hear you're having some trouble after cleaning out the pump on your washer. We recommend repeating the process and ensuring you replace the filter properly by turning it clockwise until it is fully in place and sealed. If the problem persists, please reach out to us on Facebook/Instagram/X via direct message. We'd be happy to provide additional assistance. Best, JS
Should be titled "Front Load Washer Pump *Filter* Clean Out." We cleaned out our pump filter but it didn't resolve the problem. Repair man came and found a $5 bill in the pump itself.
I have a GE front load washer and it is out of balance I redistributed the clothes but the last few washes it's still vibrating hard. I got this washer around 2004. My washer does not have the water pump in the front. Where else could this be located? Any help is appreciated
melodyvp3 We're sorry for your issue. Please take a look at our following link which includes a few suggestions we hope you will find helpful: www.geappliances.com/search/google/infobase/10000090.htm If your symptoms persist, since your model does not have the water pump in the front, service may be needed: www.geappliances.com/service_and_support/service/?ICID=supportflyout-service Thanks for reaching out to us.
Hello - we're very sorry to hear that your front load washing machine door will not unlock. Information about the front load door lock can be found at spklr.io/6057WBnb We recommend disconnecting power to the washing machine via your main home circuit breaker for a few minutes to reset the controls. If this does not help, then we recommend contacting GE Factory Service at spklr.io/6058WBnj We hope this helps! -NC
Thanks for this and other maintenance videos. They are short and concise without ads.
Hi TooLooze, We are so happy to hear that the videos are helpful to you. Sometimes less is more! Have a great day!
I can't believe it. The clothes started to get wetter and wetter after the spin cycle and I didn't know why. The machine started throwing no drain codes tonight. Found this video and then a bunch of really nasty lint and some old wrappers and stuff in the filter. Mine is a Kenmore but this video still fit the bill. Thanks GE for the customer support!
Can confirm that "Load Rebalancing" over and over was fixed by cleaning out my pump filter. Thank you!
Perfect video. short, simple, to the point. Nice checklist at the end.
Thanks so much for this! We've been using a Laundromat for weeks because we thought the repairs were going to cost a fortune. Instead, I managed to removed the sock that had somehow wedged its way in there and it didn't cost me a cent. Thanks again!
This video saved our butts! I kept calling around asking for quotes for appliance repair when our washer stopped working and the prices were a bit outrageous for a repair shop to simply check what the problem was, not even actually fix it. Started browsing, found this video, and followed these steps to fix it right away. Thanks for posting!
I'm so glad this helped. Natasha! Sure is good to save a service call - thanks for letting us know! -CC
Our system wasn't draining properly, after some Googling I found this video, we opened the filter pump and there was a brick of fabric and dog hair and other crap in there... it was super clogged, had no idea that we had to empty this. We almost called in a repair guy, but this fixed the problem. Thanks!
Steven Tyler We are so glad you found our video first, Steven!
Steven Tyle .
Steven Tyler just pull off the drain pipe and BLOW LIKE HELL!!! I used a clean wash rag so my lips didn't touch that nasty hose. After a few weeks of "blowing" treatments, my duet drains fine. But you have to make it "gurgle" . I'm sure a shopvac in reverse will work better. Blows the crap back and breaks it up to drain, it's usually just clunked up lint. Try air compression before buying expensive part. Trust me.
I found a lost ring in mine once.... ruined but was nice to finally figure out where it went
My wife has had her machine for a year now and asked me if I would help her to check the drain filter. We're in our 70's and what is easy to who ever designed and built is not so easy to an elderly couple even with50-years of D.I.Y. experience. #1.... The machine in the video is installed close to an inch higher than ours. This made all steps in the removal that much more difficult, even to the point of trying to get a small drain pan in place. Perhaps the install directions provided to company's that sell your products should come with minimum installation height requirements. #2 ..... If it hadn't been for this video we never would have figured out how to pull the drain funnel down. My wife was going on your written manual instructions until she got frustrated and came to me for help. My wife does not use a computer so for those in America still trying to live without computers or internet it might be beneficial to clarify your written instructions. #3..... The pump filter was still factory tightened and my wife found it impossible to loosen. I myself spent another 3-5 minutes trying to turn it counter clockwise until it finally broke loose. However, the space that you have allowed is so small that I ended up scraping my hand in the process. Another inch in width and length would greatly facilitate access.
Thank you thank you thank you. Because of your video I was able to drain my front loading Kenmore (nearly 10 years old) and clean the filter (every 2 months? Yikes)
I removed over a gallon of standing water, and the filter was full of hair from me, and two dogs.
I kept thinking "this will never work" It worked!!
Hi, Monique - Thank you for your inquiry. I am happy to direct you. If your washer does not have an easily accessible pump, without the removable panel, service may be needed. Our GE Consumer Service technicians are well equipped to resolve an issue such as this. Appointments may be scheduled on our GE Appliances website under the support tab. Thanks again for reaching out to us.
Thanks for sharing, Sarah! We are happy to hear your good news! Jill with GE
This video was most helpful--thank you! I'm hoping that solves the problem, and I'm confidant it will (haven't run a load yet). Like others here, I had a ton of dog hair in my filter, after washing their blankets. I was winding up with wet clothes at the end of the wash cycle and a drain cycle that went on forever, presumably putting more wear on the pump.
A couple of notes about my cleanup: I had a hard time turning the filter counterclockwise to remove it; a few light taps with a hammer got it unstuck. Since I had run a few loads after the clog occurred, there was about a gallon of water behind the clog. Even though I had a bucket set up underneath (my machine is on a pedestal), it ran into the pedestal drawer handle and into the drawer below (fortunately only had tools under there). I would suggest that if you have a pedestal, construct a way to direct the water from the pump filter compartment into a large container so that it bypasses the pedestal drawer. A piece of old tubing or even a dustpan would do it. Because my pedestal drawer can't be opened all the way due to being in a tight space, I couldn't pull it out to dump the spilled water. I used a bulb baster to remove the bulk of it and then sopped the rest up with a rag. BTW, the water in the video was a lot cleaner than what you might find in your machine!
Hello Patricia, we appreciate your comments and taking the time to post. Glad this video helped! -SF
Thanks a million to everyone who takes the time to post money saving tips on this site, our Frigidaire front loading washer wasn't going into the final rinse and spin cycle and the problem was that the coin catcher was preventing our washer from going to the final rinse and spin cycle, we found the coin catcher full of gunk and coins just like the video shows, thanks to all who share their expertise and it goes to show that all people aren't greedy like some and don't mind sharing what they know, much love to you all.
I followed the exact instruction as per the video and it has resolved my problem. Thank you! All good now.
This was very very helpful. My husband and I just got done doing draining. While draining we used shop vacuum and it’s work. Thank you for sharing.
Sir Hugh Barst, so glad that this video was helpful! Those little things have a way of making trouble for any washer! Thanks for your comments! - Sheree with GE
Thank you for the video. It helped the dryer as well since the clothes weren't soaked
Hi, Rachel Spies. Thanks for reaching out to us. Please take a look at your drain hose to ensure it is properly installed and not kinked or crimped. Also, make sure the drain in the household plumbing is not clogged. Hope this helps!
Pl
So glad you have a reference like this available here on you tube! So useful and convenient (no idea where my manual is at this time!) finding your info online was so very helpful! Thank you!
We are so happy to hear this video helped you! Please feel free to send us your model number and we will be happy to send you a manual if you'd like one. www.geappliances.com/ge/service-and-support/contact.htm?icid=GEARtopnav-contact JW
Thank you, I put a paddling pool under mine help my hand so it didn't drip down then opened it very quick so all the water shot out, do not open it quick straight away if you have a small water catcher it comes out so fast x
Thank you so much . My Samsung Washing Machine was giving "sod" error code. It was also taking too long for the complete wash. This is because a lot of dirt had got stuck in the pump filter. This Video helped a lot. :-) :-)
I have a different brand of washing machine, but this video is much clearer and useful than the one from memory machine. Txs!
Hey there Marijo! While we do recommend that you follow the instructions from your manufacturer and for your particular model (as washers can differ both by different brands and different models), we’re certainly glad our video was helpful for you. We’re happy to assist however we can, and you’re always welcome to reach out here or over our GE Appliances social media if you have any concerns or questions.
We’re wishing you all the best! -SG
@GE Appliances I am glad I found your video, and I had know cleaned the filter. Thank you!
You’re very welcome, Marijo - we’re glad we could help! Again, we’re always happy to assist if you have any other concerns or questions. Best wishes! -SG
My front loader has an issue with a queen size blanket keeps saying load rebalance, Put 1 pair of carhart overalls in does the same a load of bath towels will also make it go into rebalance mode. Never had a washer with so many problems. For being new this washer sure has issues, cleaned all filters leveled washer and rechecked several times manually rebaleance loads same issue. Never had a washer with this issue before!!!
Hi Hugh,
We're deeply sorry to hear that your washer is having so many issues with balancing and understand how upsetting this must be. We recommend disconnecting power for a few minutes then restoring power to see if that solves the problem. If that doesn't work, then we would recommend service.
You can schedule an appointment by calling 1-800-432-2737 or schedule online at spklr.io/6051YaYx. All the best. -MH
This pump filter is so much better designed than mine. Once I stop renting I'm definitely going to have to find a filter this practical! I think GE sells in the UK?
Thanks soo much this video saved me 😂 I nearly cried trying to open the door and it was locked
Omg The process took me about five minute to less to complete. Thank you for your helpfulness Xoxo gossip girl
Now you know where to come to first ;). Glad we could help!
Love how perfect this video is clear perfect instructions. All videos should be this good
Thank you for your feedback, Ryan. We're glad this video helped, and hope future videos will be of assistance to you as well. Thanks for choosing GE Appliances! -NC
Update to previous comment. Perhaps a warning about the smell of the water coming out! Wow! ;-)
I hadn't cleaned out that filter in the almost 7 years of owning our washer, and it was pretty nasty. Definitely putting a regular cleaning of that trap on my home maintenance schedule!
Again though, thanks for the video. It did the job!
What if there is stuff down deep behind that, will it come forward during the next wash
Thanks for this video...this video helped me when the washing machine was not draining and leaving giant pools of water across the floor...I removed the pump and with a pair of grips to loosen the hose clip,removed the hose to the filter...I found inside several metal bracings that go into the cup surrounds of bra`s and hairclips...also hair bands etc...those with teenage girls,beware !!!
Shallow dish > 5 gallon bucket I was trying to use before this video. Thank you!
Thank you for helping me fix my washing machine
Followed the instructions and was disgusted by how much crud I found. Glad I saved money though. Thank you!!!!
We are glad you were able to take care of it. LM
thanks Rodger your video is right on
Thanks for the awesome video. Dislikes must the the maintenance guys or the people that already bought brand new washers😂😂
Thank you so much I have the samsung washer and I didnot know how to clean the filter...these videos are so much help :-)
Hi, Carol Pedley. Thank you for your post. We regret we do not have information on the Whirlpool brand. You may want to reach out to their company website for further direction. We are always happy to help if you have any questions on GE appliances or products!
help washer won't agitate just paid 265 for full valve to be installed
Sorry for the delayed response Jamie! If you are still having issues, check out this link and see if it helps products.geappliances.com/appliance/gea-support-search-content?contentId=17398
helpful video. also on the plus side, i dont need to mop my laundry floor anymore
Yashamaruism, we are glad the video was helpful. Please let us know if you have any further questions.
Worked perfectly!
Thank you! All fixed now
Found a dryer sheet caught in there. a TON of water was leaking when turning the filter..no way to catch the water so i just kept a few towels there . I see now why it smelled a little "sewery".. Hoping that fixes the error We've been getting lately .Thank you for the vid!
KevKani340, You are welcome! So glad to hear the video was so helpful. Thanks for sharing! Alison with GE
This was extremely helpful. Thank you for the upload. I was able to safely and properly drain my machine. You are the best
Hi Anto - Thanks for your post. I’m sorry for any issue you are experiencing with your washer. You should not have to drain the filter out after each use. If you have not yet done so, please review our video, “Front Load Washer Out of Balance”, for some extra tips. Please let us know if further assistance is needed. Thanks, Jill with GE
Front load washer out of balance
How the heck are there coins??? How do the coins fit in the washing machine holes
Hi, how often do we need to clean the pump filter? Thanks
Hi, trickshots2t. We’re happy to help. Please take a look on our GE Appliances website under our “Support” tab. Here you will find some helpful tips under “Frequently Asked Questions”, “What do I do if my washer is leaking water?” We hope this will offer resolution to your issue.
I have opened it up and yes there was some money in there. Took it out, put the filter back on and pressed start again but it still stops and the clean pump light still comes back on.?? What else do I do. Thankyou
Our washer didn't work and gave the error code SE or 5E (a Samsung model) after we followed these steps it seems to work perfectly!! It saved us £50!!
Bethany Howard Awesome news, Bethany - thanks for sharing!
I did clean the drain pump had a few things in it nothing major but still the basket will not tumble will not spin is there a reset button somewhere?
The filter on my washing machine is too close to the ground to fit a tray underneath. How else can I catch the water?
designed and built by a Chinese company--Haier, who now owns GE appliances.
Worked like a charm! Thank you. :)
I have a GE Front Loader Model GFWR4805F0MC, that also likes to stop mid cycle. I found a leaf inside my drain pump housing. The washer now pauses at 37 min during a normal wash cycle. I restarted it. It started to drain at 35 minutes. Good news is the machine is not pausing numerous times like before. I believe it was doing it 3 times per load. Does anyone have any other ideas what I can look for?
Thank to for this video it was very helpful. Did anyone else notice the water that was released to have a very bad smell? Also I can’t seem to get the filter door back on, it becomes loose from the bottom. Any ideas?
Hello, my front door washing machine drain pump run without laod (makes griding noise) however, when i want to drain water through it, it won't run at all. Do you think the pump is faulty ?
Hello!
We're sorry you're having problems with your washer's drain pump. It's possible the drain hose may be kinked or clogged, or the washer pump filter may be clogged. For the best help, we recommend viewing our support article here: spklr.io/6052lMnk.
If these suggestions do not help to resolve the situation, please schedule a repair service appointment by calling 1-800-432-2737 or online here: spklr.io/6053lMnZ.
We hope this helps! We're always here if you need anything.
Take care, SH
Not so easy 🥵 rubber seal doesn’t sit properly. It takes me several tries and a floor full of water until it is properly seated to not leak. Horrible design.
We regret to hear you had some trouble and hope it has since been resolved. If we can help further please feel free to send us a PM/DM on Instagram or Facebook page with the model and serial number on your unit. We are happy to help.
It's terrible i really wish i had known this before i bought it
Currently having the same problem. Seal doesn't seat properly in the filter and can't get it to stop leaking.
If your washing machine is leaking and you are unable to seal the pump filter, please contact our GE Factory Service team at spklr.io/6050U2vq
You guys made that look easy I have it in there tight but it leaks what am I doing wrong ?
Hi, Meagan! It's true, things like this always look easier in the video. We have a helpful article here: spklr.io/6051Yi1b
We recommend making sure the filter has been screwed back in straight and is not crooked. If you continue to have trouble, please send us the model number of your washer in a DM on Facebook or Twitter. - JB
Quick question, the pump filter access door won’t come loose! I’m using a screw driver, but regardless of how I twist, wiggle or pull it just won’t come off! What should I do?
Oh my washer is next level. At the middle of the drain pipe thats where everything stucks at so i need to open the whole washers cover and unscrew all the pipes to get these out deep inside
I have a GE front loading 8 cycle heavy duty Deluxe quiet machine. Don't know the model. And I'm curious since I have a leak at the front left hand side that it might be something like this. But I do not have that small pump door. There is panel that goes across the bottom of the machine probably a foot tall. Is this something I would remove in order to find a filter pump?
Thank you for this great video!
Shernel Mardini You're welcome! We are so happy our video helped! Have a great day!
The rubber gasket has become stretched and distorted and it leaks. Can I purchase just the rubber gasket? Cant find it listed anywhere
We'd be happy to look into this for you. Please provide your model number, so we can better assist. Instructions for locating this number can be found here: spklr.io/6052sTtE
ps...if you need to remove the whole pump...remember to make sure the small electrical plug is put back into the pump housing !!!
Hi. I have the LG steam front load washer that is throwing a "check filter not draining" error just before the spin cycle.If I press pause then play button it will continue on with the cycle until the final spin where it will throw the error again.I do the same thing (pause, play) and it will finish off to the end of the wash cycle. The filter was cleaned out and I checked the drain line (watched it drain into the sink). I'm thinking that mechanically the pump is fine but electrically it may not be. Or does this sound like more of a circuit board issue? Any help is appreciated.Thanks.
Thanks for your help
We are so happy to hear our video helped with your issue Kin. JW
How often should we clean this filter .
Hi we have a aproximately 2009 front loader GE that 4x now has leaked from the back some how underneath. The water is very foul smelling like sewer water. It happened right at the beginning of the cycle. What could be the problem and the repair cost?
oh that's easy! great video
lazylarrimores We're glad you found our video to be of help to you!
So if I have to drain my washer from the front after almost every single wash, what is the issue? Drain pump? If I don’t empty it then my clothes start to smell musty. Also….is there a way to put a hose inside the front hole and leave it open all the time to drain from the hose into the drain in our floor? Help!
If I drained all of the water in my washer and it started spinning and working again the next load and it pauses and doesn’t drain on the next load what should I do?
I just cleared our drain, but there were only a couple sewing needles in it. Would that be enough to cause water all over the floor with every wash?
Hi Erica,
Thanks for reaching out. Sorry to hear about your washer leaking, we're sure this would be frustrating. If you've not done so already, take a look at the following article to see if it helps matters: spklr.io/6056cbqi
If you continue to have leaking issues we'd recommend reaching out to our service team, here: spklr.io/6057cbqc
Hope this is helpful for you.
We're here if you've got questions or concerns in the future. -MS
I am trying to clear a filter on a whirlpool awz475 turning anti clockwise but it will not release - any suggestions!
My problem is the gasket has stretched and i can no longer screw closed the wing nut, it just keeps spinning.
Hi there,
We appreciate you choosing GE Appliances and would love to help. For the best assistance, we recommend scheduling service with a verified GE Appliances technician. You can schedule service by calling 1-800-432-2737. We're confident they will fix your unit in no time. All the best. -SH
Thanks so much this video helped me I thought mine was broke
Hello Jminnie - thanks for sharing your feedback. We're glad this video helped! Thanks for choosing GE Appliances! -NC
Having a hard time putting filter tray back. It keeps turning and turning doesnt lock. Washed a load and water spewed out everywhere and of course our warranty has expired
Hi Terry,
Thanks for reaching out. Sorry to hear about the pump filter issues you've had here. If you're still experiencing difficulty with your machine, send us a PM on Facebook or a DM on Twitter/Instagram with your complete model and serial numbers. We'd like to review further for you.
If you need help finding your model and serial numbers, you can click here: spklr.io/6055lM5d -MS
I completed this task per the video but the clean filter error keeps coming back in my GEgfq14. what should I do next?
Hi Anita - thank you for reaching out to us. If you are experiencing the error code CLrFLtr on your washing machine, please see page 29 of your Owner's Manual for additional troubleshooting tips. We hope this helps! Thanks for choosing GE Appliances! -NC
My washer does not have the front where you can pull out the pump or a filter to clean, it's a whirlpool cabria
Since you have a Whirlpool washer, we recommend getting in touch with Whirlpool support at 1-866-698-2538. We hope this helps!
Can you tell me how to get a rubber gasket that goes around the knob that you turn to get the filter out?
We’d be glad to assist with your concern! Can you please clarify the model number of the washer, here or with a private message over our social media (such as Facebook or Instagram)? With that information, we can certainly look into this further.
How do you get rid of mold in the pump filter? My washer constantly stinks because of the mold in the pump filter.
Hello-Thank you for reaching out to us. We are sorry to hear you are having some concerns with your filter unit and would like to help. Could you please send us a private message with your model and serial number? Look forward to hearing back from you. All the best.- DM
My washer has a strong leak with the pump filter clean and screwed in to lock, still leaks. Why? 7:30p 4/29/2024
Copy and paste this troubleshooting link in your browser. spklr.io/6059oQif
We know you said the pump filter is screwed in completely, however that could still be the cause of the leak. Unscrew the filter and then slowly tighten it and see if that helps. If it was put back on crooked, it could still leak. If you still have leaking issues, please reach out to GE Consumer Service by calling 1-800-432-2737.
What if my washing machine doesn't have a small opening of the pump, how to clear the problem of clean pump?
I’m trying to figure out what could be causing a HORRIBLE odor from my GE profile washer. I’ve ran NUMEROUS basket clean cycles with bleach in the prewash like instructed by washer prompts and 5 cycles using afresh tablets but it’s not improved at all. It’s stinking up the entire house and even neighbors can smell it! It’s HORRIBLE. I keep the door open after washes and take clothes out right away. I did have the boot seal replaced but it appears to be sealed properly.. what else could be causing this and what can I do to resolve??? Please help!
Hello,
Thank you for reaching out to us. We're sorry to hear you are experiencing an odor from your washer. We understand how problematic that would be, and we'd love to help.
We recommend cleaning the pump filter if possible. Due to the design of the front-load washer, it is sometimes possible for small items to pass to the pump. This can restrict the draining process and may also contribute to odors. On most models, the pump filter is easily accessible for cleaning. You can view your unit's owner's manual on our GE Appliances website by searching the model number.
Below are links that provide more information on the causes and solutions to address odor issues:
Front load washer: spklr.io/6057W8PR.
Top load washer: spklr.io/6058W8Pr.
We hope this helps! Take care, SH
After cleaning out my filter, it’s leaking. Where do I get a new one?
Hello-Thank you for reaching out to us. We would be happy to help! Could you please send us a private message with your model and serial number that way we can research this further for you? We look forward to hearing from you. Sincerely-DM
I have a different model but I lost the drain plug that goes in the bottom in back. Can I use a regular plug?
Hi, we're sorry to hear you lost the drain plug, but we'd be happy to help find a replacement. Could you please reply with the model number of your appliance? Thanks. -SK
@@geappliances Yes!!
RPW 210-C..sorry this is the correct model number..
Sorry mine is RCA. spent an hour looking for it. Can I use a regular plug for it ?
Hi, because your washer was made by RCA, we suggest looking on the manufacturer's site for information on replacement parts. Thanks for reaching out to us, and have a great day. -SK
I can’t seem to turn the filter but thank you 😅
sounds silly but raise it a little off the ground and put a pot with boiling water under. let it sit for a couple minutes and that should maybe loosen it
I love you GE♥
How tight is Secure?
We would like to know a little more. Do you mind sending us a PM/DM on our Facebook or Instagram page with the model and serial number of your appliance, and more details? If you need help locating the model please see the link here- spklr.io/6055SaQl
Yep leaving my Maytag for GE! GE doesn't force you like Maytag to take off the top of your washer, then the front panel, then the rubber seal, then the bottom screw JUST to do what she has shown here you an do in 5 minutes! Insane on MAYTAG and will be leaving them bc of their engineering insanity!
Intentional maybe? outrageous ..
How often should you clean this ?
Our GE WCVH640J1WW starts to fill with water for about 30 seconds and then starts draining for a few minutes even after the water is gone and then just sits there. I knew about the access door on the front but didn't realize it was a filter, I thought it was just a drain. I removed the filter and cleaned lint and 2 pennies out of it and put it back in but still no luck. Water starts to fill for about 30 seconds, then drains for a few minutes and then just sits there doing nothing. Any ideas?
Hello GE; thank you for this tutorial video. What is the recommended frequency for this pump filter clean out procedure?
Thanks again,
Mine has no small box to open at the bottom. So where is mine?
Reading from the comments below regarding cleaning the pump after use, my washer doesn't seems to be out of balance but I have to clean it after use because of water hold up and it starts to smell with in a day. Any suggestions or advice on how to fix it?
+Jen Cruz Hi Jen, it is possible for odor to occur inside the washer tub over time. Using the appropriate amount of detergent with each load and using HE detergent can help. GE recommends cleaning the washer tub once per month to keep the wash basket fresh and clean.
For models with a BasketClean cycle:Use the BasketClean cycle and 1 cup of bleach or a commercially available product manufactured for this purpose. GE recommends Tide Washing Machine Cleaner for best results. Repeat if necessary.
For models without a BasketClean cycle:Run a large Heavy/Cotton wash cycle with no items in the wash basket and 1 cup of bleach or a commercially available product manufactured for this purpose. GE recommends Tide Washing Machine Cleaner for best results. Repeat if necessary. Tide Washing Machine Cleaner is available locally at most grocery and retails stores.
I'm desperate and in need of help from anybody who has had the problem I've got with the lint filter lid. The lid itself will not screw on properly, it's a little crooked. I've checked the grooves for any damage and lint, but it's in mint condition. It simply won't screw on right, which causes water to leak from it. Anyone had this problem as well? It's a Matsui machine for reference
I screwed the filter back in but now it wont hold the water in! It keeps dripping, non stop! What’s wrong? What should I do?
Hey there - We're sorry to hear you're having some trouble after cleaning out the pump on your washer. We recommend repeating the process and ensuring you replace the filter properly by turning it clockwise until it is fully in place and sealed. If the problem persists, please reach out to us on Facebook/Instagram/X via direct message. We'd be happy to provide additional assistance. Best, JS
Should be titled "Front Load Washer Pump *Filter* Clean Out." We cleaned out our pump filter but it didn't resolve the problem. Repair man came and found a $5 bill in the pump itself.
I have a GE front load washer and it is out of balance I redistributed the clothes but the last few washes it's still vibrating hard. I got this washer around 2004. My washer does not have the water pump in the front. Where else could this be located? Any help is appreciated
melodyvp3 We're sorry for your issue. Please take a look at our following link which includes a few suggestions we hope you will find helpful:
www.geappliances.com/search/google/infobase/10000090.htm
If your symptoms persist, since your model does not have the water pump in the front, service may be needed:
www.geappliances.com/service_and_support/service/?ICID=supportflyout-service
Thanks for reaching out to us.
I see. Thx for replying me.
Thank uu
I followed these instructions but i didnt find anything in the pump filter. The washer door still won't open.
Hello - we're very sorry to hear that your front load washing machine door will not unlock. Information about the front load door lock can be found at spklr.io/6057WBnb We recommend disconnecting power to the washing machine via your main home circuit breaker for a few minutes to reset the controls. If this does not help, then we recommend contacting GE Factory Service at spklr.io/6058WBnj We hope this helps! -NC