Ford Mondeo MK4 tachometer / speedometer change / MiniDOT to Convers+ / Forscan mileage adjustment

Sdílet
Vložit
  • čas přidán 29. 08. 2024
  • Change small dashboard MiniDOT to Convers+ on Ford Mondeo MK4 2.0 TDCI 2009. Mileage adjustment via Forscan.
    Výměna rychloměru (budíků) MiniDOT za Converse+ na vozu Ford Mondeo MK4 2.0TDCI. Nastavení ujetých kilometrů pomocí Forscan.
    Music:
    Rocky Mountains - Scandinavianz [Audio Library Release] · Free Copyright-safe Music

Komentáře • 72

  • @michael-mpmovies
    @michael-mpmovies Před 5 měsíci

    Thanks a lot! I just needed to replace the front speaker of the PDC but didn't know how to remove the tachometer. After this video it was super easy! Thank you!👌

  • @WiggyRS
    @WiggyRS Před 24 dny

    i got the same as the one you replaced, but i got a problem (especially during winter) that none of the electronics works. The engine starts fine, but sometimes when i start my car or while i drive, the electronics shuts off. So i cant see how fast i drive, how much fuel is left etc. Even the mid consoler doesnt have electricity. Checked all the fuses, and nothing was wrong with it.
    This doesnt happen often, but enough to be annoying. A friend of mine checked it, and he just used his fist and knocked on the dashboard, right behind the steeringwheel, and all the electronics worked again.
    Do you think its just a wire that got a loose connection? such as the connection wire you disconnected?

    • @jockejoj
      @jockejoj Před 10 dny +1

      Hi, try just to remove the connector, spray with electric cleaner at the pins in the instrument part of connector and install everything again as in video. Most probably bad connection. A common problem.

  • @jonyelectrosur3102
    @jonyelectrosur3102 Před rokem +1

    Hola amigo muy buen trabajo!! El inmovilizador está el IPC? También tuviste que sincronizar las llaves?

    • @Placekmich
      @Placekmich  Před rokem

      Hello, no key adjustment is needed. Just exchange of dashboard and mileage adjustment. Nothing else is needed.

  • @martinspakalns2539
    @martinspakalns2539 Před rokem +2

    Hi. How to know exactly wich convers speedometer is right for car? Or any facelift diesel speedo from mondeo, smax, galaxy will work? I have mondeo 2011 1.6tdci estate.

    • @Placekmich
      @Placekmich  Před rokem +4

      If you have Mondeo MK4 facelift diesel, you have to use Mondeo MK4 facelift diesel dashboard - tacho. Does not matter if maxidot or convers. You just have to keep the car model, generation and fuel.

  • @stylo8133
    @stylo8133 Před 2 měsíci

    I have problems with interior light?
    With old one it works. When i put the converse+ in everything works accept interior light.
    Please help

    • @Placekmich
      @Placekmich  Před 2 měsíci

      Unfortunately I have no clue why you interior light doesn't work. I never faced to the similar problem.

  • @antonmarinov6091
    @antonmarinov6091 Před 9 měsíci

    Thanks for the very good tutorial! What kind of diagnostic tool are you using for Ford?

    • @Placekmich
      @Placekmich  Před 9 měsíci +1

      Hi, thank you. I am using vLinker FD+.

  • @entendatudo5605
    @entendatudo5605 Před rokem +1

    Hello friend! is it possible to use 2014 ford mondeo steering wheel and speedometer in 2010 ford focus? I have a 2010 Ford Focus and I would like to use the steering wheel and this digital speedometer, but I need to know if it is possible to exchange the information so as not to have a reading error. can you give me this information?

    • @Placekmich
      @Placekmich  Před rokem

      Hello, unfortunately I have no experiences with Focus. Only Mondeo and S-max.

  • @XIXAO008
    @XIXAO008 Před 3 měsíci

    Zdravím, jaký kabel jste prosím použil? Mám Forscan extended a při posledním kroku přenastavení nájezdu mi Forscan vyhodí chybu "servisní procedura byla přerušena". Mám kabel ELM327 v1.5 s manuálním přepínačem HS/MS CAN. Na rozdíl od Vás potřebuji nájezd snížit. Díky za odpověď. Auto je Mondeo 2.0 TDCi 2011, budíky convers+ facelift.

    • @Placekmich
      @Placekmich  Před 2 měsíci +1

      Zdravím, já používám kabelovou verzi ELM 327 s manuálním přepínačem a pak BT verzi vLinker FD s automatickým přepínáním. Nicméně pokud se nemýlím, tak přes Forscan lze upravit kilometry pouze směrem nahoru. Na snížení bude pravděpodobně potřeba jiný SW. Který bohužel nevím.

  • @Myissha
    @Myissha Před rokem

    Hmmm, jste sikovny!

    • @Placekmich
      @Placekmich  Před rokem +1

      Děkuji! Mé služby jsou Vám kdykoliv k dispozici! 😆

  • @galerazija
    @galerazija Před 10 měsíci

    Hey - awesome video :) thanks. Quick question - I have 2007 Pb with km/h - do I need to find Convers for this exact one? I mean mostly kmh and year of production. Or all I should be worried is type of fuel? I' veen british clocks have also kmh numbers so I can change clocks later on I guess but I am afraid if I should seek for very specyfic for 2007 or any for MK4 will do?

    • @Placekmich
      @Placekmich  Před 10 měsíci +1

      Hi, thank you. The gasoline version has more RPM than diesel one. So in my opinion you should use dashboard from the same type of fuel as you have. Mileage you can adjust upwards by yourself using OBD diagnostic and Forscan extended licence. Downwards you have to find somebody with special diagnostic. About the year - you just need to keep pre-facelift version. Facelift version could be used but it has to be adjusted by somebody who knows how to do it - otherwise the airbag sign icon will appear.

  • @thisistheway1766
    @thisistheway1766 Před 6 měsíci

    Hello
    i have a mondeo mk4 and i have changed the instrument cluster but as soon as i connect it a beeping noise starts

    • @Placekmich
      @Placekmich  Před 6 měsíci

      I would recommend to connect car to the diag to see what is happening.

  • @solarsolari6705
    @solarsolari6705 Před rokem

    I installed a Mondeo on a Galaxy but it keep beeping. Like an open door beep. Any idea what it can be? Both are none titanium models. My Galaxy had the small middle lcd blacked out

    • @Placekmich
      @Placekmich  Před rokem

      Hi, I would recommend to read error codes on diagnostic. Normally when you change dashboard no beeping is present.

  • @jozefdrlicka4068
    @jozefdrlicka4068 Před 3 měsíci

    Ahoj, kúpil som si nové OBD, origo k aplikácii forscan a stále mi neukazuje položku nájazd kilometrov, potrebujem kilometre znížiť, poraď čo mám robiť aby mi to fungovalo

    • @Placekmich
      @Placekmich  Před 2 měsíci

      Ahoj, podle stránek forscan.org jdou kilometry pouze navýšit a to z rozšířenou licencí, která je zdarma na 2 měsíce (pak se dá znovu prodloužit). Pokud potřebuješ jít s KM dolů, budeš potřebovat pravděpodobně jiný SW. Bohužel já takový neznám. Ale na Ford fóru, nabízejí dohrání různých funkcí do budíků Convers+ tak by mohli umět i snížit km.

    • @jozefdrlicka4068
      @jozefdrlicka4068 Před měsícem

      Akú verziu forscan si mal nainštalovanú keď si to resetoval

  • @stefanoES23
    @stefanoES23 Před 10 měsíci

    hi m8, I have changed mine but I have the buzzer continuously on and I dtc regarding wrong configuration, do you have any ideea why?

    • @Placekmich
      @Placekmich  Před 10 měsíci

      Hi, actually I don't have any issue with buzzer after swap. Try to figure out which configuration is not correct. In my case I only changed the mileage on the dashboard nothing more. A did this swap o my both cars - mondeo and s-max.

  • @dzemalhabul5622
    @dzemalhabul5622 Před 10 měsíci

    Great video friend, tnx 🙏.
    Do you now is it posible to register / activate climate controler for Mondeo with this Forscan? Just did the face lift to my from 2010 tdci 2,0 Ecconetic. The only problem is climatecontroler. Thank you 🙏

    • @Placekmich
      @Placekmich  Před 10 měsíci

      Hi, thank you. With the forcan you can set entertainment level of the car which includes also changes in climacontroler. But I never tested it personally so I cannot tell you for sure.

  • @romanchylek5315
    @romanchylek5315 Před 5 měsíci

    hi very helpful vid is there any chance that i can do the mileage correction by myself?Just bought converse + and i’m about to swap it

    • @Placekmich
      @Placekmich  Před 4 měsíci

      You can adjust kilometers upwards using Forscan extended licence.

  • @zvezdelinvelikov8050
    @zvezdelinvelikov8050 Před rokem

    Hello friends! I have a question, my car is left-hand drive, can I install a dashboard from a right-hand drive car? Will the buzzer work with lights left on when opening the front left door? Thanks!

    • @Placekmich
      @Placekmich  Před rokem

      Hi, honestly I don't know... But I think it should work, because all open doors are visible on the dashboard...

    • @zvezdelinvelikov8050
      @zvezdelinvelikov8050 Před rokem

      ​@@Placekmich Very hard to find a left hand drive dash. I'm looking for a right-hand mounting panel. Thanks for the help! I'm glad there are people like you. Greetings!

    • @jozefdrlicka4068
      @jozefdrlicka4068 Před 10 měsíci

      In my opinion, it would be necessary to use alarm clocks with miles.

  • @tonyhaz6664
    @tonyhaz6664 Před rokem

    Hi.
    I need to put new clocks in my mondeo mk4 as clusters gone, will I be able download and use forscan for free?

    • @Placekmich
      @Placekmich  Před rokem +2

      Hi, yes. Forscan can be download from page forscan.org and there is also possibility to get 2 moths extended licence for free.

  • @PModesto
    @PModesto Před rokem

    Will this work on a Ford S-Max 1.8 TDCI from October 2006?

    • @Placekmich
      @Placekmich  Před rokem

      Yes it will work. Only problem could be with old radio unit that will not show on the dashboard what is playing. Same as on my video.

    • @PModesto
      @PModesto Před rokem

      @@Placekmich I have an Chinese Android radio.
      I saw in some video comment that it doesn't work on 2006 S-Max, it will not light up the dash lights.

    • @Placekmich
      @Placekmich  Před rokem +1

      My s-max is from end of 2006 and it works. If you have Android radio and correct canbus it should work normally...

    • @PModesto
      @PModesto Před rokem

      @@Placekmich There's a more beautiful dashboard from FORDS-MAX (WA6)1.6 TDCi
      [2011-2014].
      Do you know if it is also compatible with October 2006 1.8TDCI Ford S-Max?
      Or have to be like the one you show in your video?

    • @Placekmich
      @Placekmich  Před rokem +1

      @@PModesto It could be used but there has to be modified firmware in the dashboard unit. Without this update it is not compatible.

  • @dohanyos111
    @dohanyos111 Před 11 měsíci

    Ahoj chcem sa spýtať či sa dá kúpiť novy budík alebo len používane sa dá zohnať.Poprípade kde by sa dalo zohnať ? Ďakujem Vopred.

    • @Placekmich
      @Placekmich  Před 10 měsíci

      Ahoj, o novým jsem neuvažoval a ani nehledal, podle mě to bude strašně drahé a možná i nesehnatelne. Na druhou stranu používaných se dá sehnat relativně dost a je spousta lidí, co je dokáží modifikovat na lepší funkce.

    • @romanchylek5315
      @romanchylek5315 Před 5 měsíci

      ja sem si teď koupil ten converse+ a jdu to vyměnit a už teď mám hrůzu z toho nastavení…hlavně km at pasujou atd atd

  • @leandrompdelgado
    @leandrompdelgado Před rokem

    Hello, is it possible to go back on km? I want to change my gauges too but actually my maxydot has 190k and the convers+ has 249k, need to go back on km. Can do it with the same program? Thanks

    • @Placekmich
      @Placekmich  Před rokem +3

      Hi, unfortunately it is not possible via Forscan. With this software you can increase KM only. Maybe with using UCDS software it will be possible, but this I did not test.

    • @leandrompdelgado
      @leandrompdelgado Před rokem

      @@Placekmich thanks, I'll check it 😜

  • @mesani1
    @mesani1 Před rokem

    Super videa mám dotaz. Jak jsi dostal češtinu + stejný nájezd mám GALAXY 2010 2,2 tdci. Mám stejnou diagnostiku jen základní.

    • @Placekmich
      @Placekmich  Před rokem

      Díky! Nájezd jde změnit směrem nahoru s rozšířenou licenci forscan (na 2 měsíce zdarma a dá se obnovovat po vypršení) - to byl můj případ, budíky měly min než moje auto. Češtinu jsem nechal nahrát od kluka z Ford fóra. Nahrál mi češtinu na parkovišti před lidlem za 10 min ☺️

    • @mesani1
      @mesani1 Před rokem

      @@Placekmich Díky moc. Jinak videa pěkně a srozumitelně natočená nevzdávej se já teď čistil u svého 2.2 129 kW EGR na prášky. Toč dál držím palce.

  • @jozefdrlicka4068
    @jozefdrlicka4068 Před 10 měsíci

    Ahoj, vymenil som si budíky presne také isté ako máš aj ty. Tiež použivam Forscan , ale kolonka zápis nájezdu mi tam nevyskakuje, tým pádom si nemôžem upraviť kilometre, aký máš upgrade Forscan

    • @Placekmich
      @Placekmich  Před 10 měsíci

      Ahoj, jde to přes forscan extended licenci která je free na dva měsíce (ale pak se dá znovu obnovit). Návod najdes na stránkách forscan.org

    • @jozefdrlicka4068
      @jozefdrlicka4068 Před 10 měsíci

      Mám kúpenú licenciu ale nechce mi načítať riadiacu jednotku budíkov, namontované ani origo rádio. Skúsim namontovať origo rádio aj s origo budíkmi , uvidím čo mi to ukáže.

    • @jozefdrlicka4068
      @jozefdrlicka4068 Před 10 měsíci +2

      Zistil som čím to asi bude, nemám origo obd pre Forscan, tým pádom mi neprenáša všetky údaje. Idem zohnať origo OBD potom dám vedieť.

  • @justaskersnauskas3862
    @justaskersnauskas3862 Před 6 měsíci

    hi, can i put this dashboard in a pre fl model 2007?

    • @Placekmich
      @Placekmich  Před 6 měsíci

      Hi, yes. This dashboard is pre-facelift version.

  • @jurajmargetin85
    @jurajmargetin85 Před rokem

    Ahoj.Bude pasovat nova pristrojovka,taka aku si daval aj na mondeo 2007,2.0 benzin 107 kw?Dakujem

    • @Placekmich
      @Placekmich  Před rokem +1

      Ahoj, pokud se jedná o Mondeo MK 4, tak ano. Je musíš hledat benzinovou verzi (má víc otáček na otáčkoměru).

    • @jurajmargetin85
      @jurajmargetin85 Před rokem

      Dakujem velmi pekne za odpoved.Nooo dufam ze najdem.

  • @davidcarr3052
    @davidcarr3052 Před rokem

    Can this be done on. Grand x max 2011

    • @Placekmich
      @Placekmich  Před rokem

      Hi, I am not sure, but I think that it cannot be done at grand c max. It could be done on mondeo, s-max and Galaxy for sure.

  • @denisdobre8590
    @denisdobre8590 Před rokem

    Do you know how to change from MPH in KPH?

    • @Placekmich
      @Placekmich  Před rokem

      Hi, probably via diagnostic, but honestly I never did this change.

    • @sezginylmaz3757
      @sezginylmaz3757 Před 4 měsíci

      Hi did you solved ?

  • @SimracingGT698
    @SimracingGT698 Před 11 měsíci

    Is this plug and play or does it need coding

    • @Placekmich
      @Placekmich  Před 10 měsíci +1

      Coding is needed just for mileage correction. The rest is just plug and play.

    • @romanchylek5315
      @romanchylek5315 Před 5 měsíci

      @@Placekmichplease help me somebody with the mileage correction i bought the cluster instrument and i’m actually angry…now i have to find the right person with right skills and right program for it

  • @2cezand
    @2cezand Před rokem

    Diagnostic interface and program mame please

    • @Placekmich
      @Placekmich  Před rokem +1

      Hi, I am using Forscan software (it's free) and modified Elm 327 scanner with ftdi chip a.aliexpress.com/_Ew6yCE9