Can you do a video showing the functional difference between the 2.0 and 3.0? I understand the numbers, but it would be nice to SEE it. Hope that makes sense.
Rein 3.0 18650 - Full Size Specs .100,000 Candela peak beam intensity (With 18650) .1250 Lumens output (With 18650) .95 minutes run-time (With 18650) .Dual-Fuel capability. REIN 3.0 runs on 18650 and now, can also run on two CR123 batteries. 18650 rechargeable battery provides the best output, by far. However, you can now use 2 CR123 batteries if needed. You will see reduced output with CR123 batteries. .1.3” Bezel diameter - smaller than the original REIN in diameter. .6.17” Long - a very compact full-size light. .The same reduced mounting lug height as the REIN 2.0. Shorter than the original REIN 1.0 allowing for tighter mounting.
Well done, Cloud. I have a REIN and HC handheld for work and really like them both. If this 3.0 is really dual fuel with CR123s that changes things in a big way for serious use. Looking forward to getting one of these.
Beautiful! Love what you guys do! You should make a IR Laser with a Illuminator! I know the technology is advancing and I know it's expensive. If you made it! I'd buy it! Go Cloud Defensive!
We can publish our data that we derive from our laboratory grade integrating spirit equipment. That’s easy to do. Will gladly get that information out sooner or later. I wouldn’t worry too much about third-party testing. There is no way to ensure neutrality. We’re not going hazard the entire company by giving bad data. Truth be known, most of these lights are clock in substantially higher than 100,000 candela. We rate em lower now. I’ve seen 3.0s clocking over 110,000 actually.
@@CloudDefensive I get where you guys are coming from and your products are excellent, but I trust Werkz and their methods. I own an OWL and a REIN, so you guys are my go-to for rifle mounted lights and maybe pistol when that finally hits.
Cool. Still wish you reversed your dual output tailcap on your MCH from Low to High to High to Low. If I need high I want it immediately. If I need low to preserve my night vision, I can just hold the bezel against my leg and toggle through the modes and take my time.
I would also like to see a direct comparison video as well. Cloud is the absolute best without question. I have an owl, a rein 2.0, and will likely have a host of other lights from them in the future. Look up the owl torture tests they did if you have not already...sheesh.
I bought a Rein 1.0 Micro almost two years ago now. Since then your company has released the 2.0 Rein, and the 3.0 almost immediately afterwards. I love your company. Wish there was some more clothing and swag on the merchandise side of your store that way I could rep your brand. I love everything your company does. My wallet on the other hand chooses not to give its opinion. Can’t wait to tell my family that this is the late Christmas gift I have in mind. Thank you Cloud!
I have the owl and recently got the rein 2.0 the difference is amazing!! The 3.0 is even better!!! A company using innovation to improve their products. No protectionism or rent seeking mechanism’s for government dollars. This is how it’s done .
I know this won't happen, and it comes with lots of issues and whatnot. But. It would be fucking amazing to have a list of ETAs on your website for upcoming products. I know 6 people will bitch when the dates change or aren't perfectly accurate, but the rest of us would absolutely love it. Y'all could be industry leading in this, and it would fit what you do and how you do it extremely well.
It’s not without irony that we can’t do that because every time we talk about upcoming projects, the Internet explodes. The only thing we can do is tell the world about new products a couple of weeks before they drop. Anything more aggressive than that and heaven forbid our timelines shift…and the world implodes. 😂😂 I say that half joking, but also have serious. I understand why you ask that but it’s just not possible.
Very cool. I'll order one in the new year, probably from Big Tex Ordinance. I learned my lesson with the MCH on ordering launch day products from Cloud.
We learned a lot of lessons too. We've spent a significant amount of time this year making improvements. We're in our new much larger facility and we've hired a lot of new people. We have more lights available for this launch than ever before.
Also - if you would be so kind as to please purchase one from our website the day of launch, I would very much appreciate the chance to correct mistakes of the past. We’re so much better than we were.
Are these going to be a whiter/cooler light than the original REIN? I find that I prefer the bright white to the warm yellow of the original. If so I may ditch some of my SF DF ScoutLights if it compares.
I got my Rein 2.0 Micro within a month of its release and I still feel like it’s brand new lol. I also got the Valhalla Tactical Baldr light body w/ integrated mounting system for it, which I love and it wasn’t exactly cheap… So I hope it’s compatible with the 3.0.
I just got the Rein 2.0, will I be able to purchase a 3.0 light head and screw it on the 2.0 body or am I going to have both the #1 and #2 light out there?
I think the color temp is cooler compared to my Rein 1.0 I prefer the warmer color because it shows true color of what I’m lighting up as well as more detail. What is the actual color temp of the 3.0?
It would be rad if you showed the 2.0 and 3.0 at 100, 200, and 300 yards, and show two nameless lights in comparison. Those nameless lights might or might not be the PLHv2 and the OKW. We’ll never know…
We will try to make that happen. The weather has been pretty terrible around here and we are smart as you might imagine. But that is something we need to show. I’m not interested in showing our competition however. It’s easy to show 1.0 versus 2.0, verse 3.0 however. 3.0 wins the day.
Candela is a function of the realities that we face in the physical world. Meaning the physics does not support Uber high candela out of small light heads. That is why the 3.0 is nominal a larger. As such, even if we put the new tech into the smaller head. It would not perform like the three point out. It would still be damned impressive, but not as much.
@@soulshot96 eventually but to maximize profits it's smarter to release the entire package for the first month or so. Then pistol light (maybe) then rein 4.0 with 40 minutes of runtime but 250k candela.
Interesting, the OKW is already a lightsaber so the idea of having something even more powerful and by this much of a margin is mindboggling. My only concern is the power draw, and the heat management. I am assuming this isn't an LEP so that means we are potentially looking at a lot of heat, and a major power hog, and I am curious how long it will last before it needs to step down.
You are looking at a lot of heat, but then again, this is a weapon mounted application. Much like a suppressor it’s not something you’re grabbing hold onto. We actually thermally regulated this in such a way that you get far superior thermal step downs than what was previously available on 2.0…And because we let the light get hotter, it performs better for longer. Everything I just said he’s not really been spoken about yet in our media, but is upcoming. This is a substantial leap forward.
Due to enhanced thermal upgrades, the REIN 3.0 light head CANNOT be used on any MCH lights. Simply, the light head gets too hot which can cause damage to the electrical components.
Does the 3.0 full size come with the push button tail cap or is that a separate purchase only? Does the dual button remote switch come with the LCS dual button side plates or is that a separate purchase only?
The Rein 3.0 comes with push button tailcap and a single button remote switch. The dual button switch comes with everything you need including sideplates. It's a direct swap from the single button.
All that info is forthcoming. Hang tight. Long story short yes they are compatible but we have absolutely no expectation on when we would have heads for sale. Demand for complete light systems is so intense we have 100% of our available capacity allocated towards that right now and it will be that way for the foreseeable future.
Our MCH light is the closest equivalent to a Rein handheld. We offer them with various heads depending on your use case with a handheld. The MCH Duty and MCH-HC are most likely what you're looking for. Micros will be available very soon as well.
...I doubt it. The rein 2.0 came out months ago. There’s nothing in this light that didn’t exist years ago. I think they want to keep releasing bigger and better ones for more money. Why would they make the best right away, when there’s people who buy each one because it’s better than the last..?
@@KimballPrecisionRifles well they have been developing the rein 2.0 for quite some time I believe. This video suggests that it wasn't possible previously I would just like that confirmed.
You guys are going to make me go broke!! ;-) I have an OWL as well as a Rein 2.0 and they are impressive to say the least! What colors will it come in? My Rein 2.0 is supposed to be in O.D. green but that color does not match my OWL - which is actually O.D. green. (Please go back to the original O.D. green color!)
Only concern is being able to buy just a head. I own a 2.0 and MCH, but still can’t get just a 2.0 head for my 1.0. Will heads be available this time? I really don’t need a whole new light.
exactly this. tbh the 3.0 isn't going to be worth it for most people who just bought the 2.0 this year or have a 1.0 already, But selling just the heads would be pretty nice. Especially if you could trade in your 1.0 or 2.0 heads. seems like the 3.0 beats the 2.0 in every way, It basically makes the 2.0 obsolete. Personally I prefer the 1.0 over anything else despite being dimmer because of the field replaceable lens, heatsink capabilities, and S7 bezel. Really salty that it's not longer available despite them saying it would be. I'd buy a 3.0 head with those features in a heartbeat. I'm such a small demographic of customers though that I doubt I'll ever see it
They've had an faq question about it since the 2.0 was coming out, saying a trade in program was in the works and sign up for their newsletter (obviously). Just sell the damn heads already, I'll buy one to get rid of the 1.0 behemoth
@@WeaponizedAutismiii you don’t even need a retro fit to run a 2.0 or 3.0 head. While they were still only making the gen1, they switched from a single coil spring in the tap cap, to a 2 coil spring. As long as you check that your tail switch has the 2 coil spring, you can run any of the light heads. They just have to make them available for purchase.
@@CloudDefensive Thanks! Any plans on a dual button switch that allows a split connection to a cloud light and something like Peq15? I think that's the main thing keeping me from ditching all my surefire for cloud!
If y'all want to make some money; could you please make a direct competitor to the Streamlight TLR7a? If you could make a comparable sized version that produces 20k candela and still with good spill you would take 5 - 15 percent of their market share, I think.
Guess I'm glad I never managed to snag a REIN 2.0 which has been out for about fifteen minutes.😂 So guys, WTF is up with the OWL? Is it discontinued? It's not on the web site and I've heard nothing. An updated OWL would excite me more than a third version of the REIN (fwiw, I've got an OWL and a REIN 1.0).
They were gearing up for the 3.0 Rein release. They will make more OWL's they've told me but didn't provide an ETA. I'm wondering if it will be a OWL 2.0? I love my OWL's!
Can you do a video showing the functional difference between the 2.0 and 3.0? I understand the numbers, but it would be nice to SEE it. Hope that makes sense.
The biggest difference is gonna be throw
No real functional difference, 60k candela opposed to 100k is SUBSTANTIAL the throw is gonna be incredibly far for a non LEP light
I wish cameras did a better job of showing what the human eye actually registers. 3.0 is just more of everything.
@@CloudDefensive higly agree! You have to get one in hand, once I did I understood. Fantastic work fellas
There's plenty of videos showing the differences side by side on CZcams. czcams.com/video/tPNPknqqHlU/video.html
Gentlemen, you had my curiosity, but now you have my attention.
Boom
🫡
Some of the best lights available. Outstanding work, gents. Still running an older Micro REIN, and haven't had a single issue.
Thank you for the kind words!
I love my micro rein. Thing is sick.
Have the Rein 2.0 on my MK18 and put the 3.0 on my SPR for work. Cloud Defensive is a step above everyone else. Phenomenal products.
Rein 3.0
18650 - Full Size Specs
.100,000 Candela peak beam intensity (With 18650)
.1250 Lumens output (With 18650)
.95 minutes run-time (With 18650)
.Dual-Fuel capability. REIN 3.0 runs on 18650 and now, can also run on two CR123 batteries. 18650 rechargeable battery provides the best output, by far. However, you can now use 2 CR123 batteries if needed. You will see reduced output with CR123 batteries.
.1.3” Bezel diameter - smaller than the original REIN in diameter.
.6.17” Long - a very compact full-size light.
.The same reduced mounting lug height as the REIN 2.0. Shorter than the original REIN 1.0 allowing for tighter mounting.
I appreciate your willingness to improve and listen to your fanbase. It’s why I buy cloud lights. Thank you
Thanks man!
Well done, Cloud. I have a REIN and HC handheld for work and really like them both.
If this 3.0 is really dual fuel with CR123s that changes things in a big way for serious use. Looking forward to getting one of these.
It is indeed DF. 👊👊
*can't wait for mine to get here! just ordered one in the ODG color!*
i was gonna get another light for yet another build and now i'm glad i waited
Just ordered mine today. Currently have Modlites, Arisaka and Cloud Defensive lights on my builds. I hope this as good as you say.
3.0 announced on your FB page literally 2 days after I receive my 2.0. 😂. That’s what I get for not waiting.
Absolutely going to need a 2.0 & 3.0 video comparison excited fs
Been hearing about QC issues for the 2.0 Reins. Hoping the 3.0 and the new facility helps handle the issues I’ve heard about. Love y’all’s products.
Not sure what you have heard. But these are the finest lights we’ve ever made. And we warranty them forever.
Beautiful! Love what you guys do! You should make a IR Laser with a Illuminator! I know the technology is advancing and I know it's expensive. If you made it! I'd buy it! Go Cloud Defensive!
Thank you for the support!
I second this^
@@CloudDefensive yep do it. No balls!
thn everybody would bitch when they saw the 3500 dollar price tag
I'd settle for an IR Flood!
Or maybe incorporate a IR laser into the bezel..
(I want royalties if you do this💯🤣)
Love my new rein 3.0.
I discovered you can use it to make toast because of how bright it is.
0:08
Oh lawd he comin
Now this light could just be the one WML to rule them all, the candella and lumens output is just astonishing
She's bright :)
I'm super happy with my og rein. Would gladly pick this up down the road
The OG REIN is still legit.
@@CloudDefensive I have no regrets about it for sure. But I do have a couple rifles with no lights that could use the new models
I'll wait for Werkz to run their tests. Looks cool though and crazy if it hits specs.
We can publish our data that we derive from our laboratory grade integrating spirit equipment. That’s easy to do. Will gladly get that information out sooner or later. I wouldn’t worry too much about third-party testing. There is no way to ensure neutrality. We’re not going hazard the entire company by giving bad data. Truth be known, most of these lights are clock in substantially higher than 100,000 candela. We rate em lower now. I’ve seen 3.0s clocking over 110,000 actually.
@@CloudDefensive I get where you guys are coming from and your products are excellent, but I trust Werkz and their methods. I own an OWL and a REIN, so you guys are my go-to for rifle mounted lights and maybe pistol when that finally hits.
@@Metallica8589 I like how Werks them to the test as well.
Agreed on Werkz testing, and a standardized method. Fishy that you don’t follow the protocol and say “just trust us”
Cool. Still wish you reversed your dual output tailcap on your MCH from Low to High to High to Low. If I need high I want it immediately. If I need low to preserve my night vision, I can just hold the bezel against my leg and toggle through the modes and take my time.
I would also like to see a direct comparison video as well. Cloud is the absolute best without question. I have an owl, a rein 2.0, and will likely have a host of other lights from them in the future. Look up the owl torture tests they did if you have not already...sheesh.
First time I've seen the flow556k glowing :)
I bought a Rein 1.0 Micro almost two years ago now. Since then your company has released the 2.0 Rein, and the 3.0 almost immediately afterwards. I love your company. Wish there was some more clothing and swag on the merchandise side of your store that way I could rep your brand. I love everything your company does. My wallet on the other hand chooses not to give its opinion. Can’t wait to tell my family that this is the late Christmas gift I have in mind. Thank you Cloud!
It is a brighter whiter white if you will, compared to 2.0
Trade up program? :)
Love you guys thanks
Any chance of an IR light in the future? Seems like Surfire has the market cornered on the IR/White lights and I think you could do better.
I have the owl and recently got the rein 2.0 the difference is amazing!! The 3.0 is even better!!! A company using innovation to improve their products. No protectionism or rent seeking mechanism’s for government dollars. This is how it’s done .
I like that...do you have any IR products im looking?
I know this won't happen, and it comes with lots of issues and whatnot. But. It would be fucking amazing to have a list of ETAs on your website for upcoming products. I know 6 people will bitch when the dates change or aren't perfectly accurate, but the rest of us would absolutely love it. Y'all could be industry leading in this, and it would fit what you do and how you do it extremely well.
It’s not without irony that we can’t do that because every time we talk about upcoming projects, the Internet explodes. The only thing we can do is tell the world about new products a couple of weeks before they drop. Anything more aggressive than that and heaven forbid our timelines shift…and the world implodes. 😂😂 I say that half joking, but also have serious. I understand why you ask that but it’s just not possible.
What’s the beam distance on this? I’ve got a Olight Javelot Turbo. Curious how they compare. The battery options on this is nice
Will the head work with a 1.0 body, and will it sell separately? I've got 2 1.0's that could use an update.
Can we connect to other brands tapeswitches like the Surefire D07?
I...just bought a 2.0. Ah, well. Have a couple 1.0s too.
Any chance of getting the updated heads eventually or am I SoL?
Awesome! When pistol light?
Very cool. I'll order one in the new year, probably from Big Tex Ordinance. I learned my lesson with the MCH on ordering launch day products from Cloud.
We learned a lot of lessons too. We've spent a significant amount of time this year making improvements. We're in our new much larger facility and we've hired a lot of new people. We have more lights available for this launch than ever before.
Also - if you would be so kind as to please purchase one from our website the day of launch, I would very much appreciate the chance to correct mistakes of the past. We’re so much better than we were.
Are you gonna make just the heads, so we can upgrade the lights we have ?
Will we be able to use the weapon light trade in code for the 3.0 as well, or is it just for the original models ?
Are these going to be a whiter/cooler light than the original REIN? I find that I prefer the bright white to the warm yellow of the original. If so I may ditch some of my SF DF ScoutLights if it compares.
I got my Rein 2.0 Micro within a month of its release and I still feel like it’s brand new lol. I also got the Valhalla Tactical Baldr light body w/ integrated mounting system for it, which I love and it wasn’t exactly cheap… So I hope it’s compatible with the 3.0.
I just got the Rein 2.0, will I be able to purchase a 3.0 light head and screw it on the 2.0 body or am I going to have both the #1 and #2 light out there?
I think the color temp is cooler compared to my Rein 1.0 I prefer the warmer color because it shows true color of what I’m lighting up as well as more detail. What is the actual color temp of the 3.0?
I need this.
Yes you do.
Is that simply just a mount, or is it more what it looks like - an OWLish mount/switch combination?
It would be rad if you showed the 2.0 and 3.0 at 100, 200, and 300 yards, and show two nameless lights in comparison. Those nameless lights might or might not be the PLHv2 and the OKW. We’ll never know…
If the 3.0 can noticeably beat out the okw I’ll be impressed
We will try to make that happen. The weather has been pretty terrible around here and we are smart as you might imagine. But that is something we need to show. I’m not interested in showing our competition however. It’s easy to show 1.0 versus 2.0, verse 3.0 however. 3.0 wins the day.
Will it light up a tree line 250yards out?
Will the head fit on an mch body? I know it’s not designed to but idc
Nice! I'm in need of another CD light anyways...REIN 3.0 it is!
Love the Cloud products, this is exciting tech. Will the new higher candela heads added to a MCH 2.0?
Candela is a function of the realities that we face in the physical world. Meaning the physics does not support Uber high candela out of small light heads. That is why the 3.0 is nominal a larger. As such, even if we put the new tech into the smaller head. It would not perform like the three point out. It would still be damned impressive, but not as much.
@@CloudDefensive great info to have, thanks for the response!
Cloud defensive are you guys doing another hand held any time soon.
Any chance we could get another video showing the equipment itself, like the light and the included switch (provided you've changed it at all)?
More content coming soon. The only change is the diameter of the head. The rest of the light is identical to the 2.0
@@CloudDefensive Will you offer just the head so 2.0 users can upgrade easily?
@@soulshot96 eventually but to maximize profits it's smarter to release the entire package for the first month or so. Then pistol light (maybe) then rein 4.0 with 40 minutes of runtime but 250k candela.
Price point gonna be comparable to the 2.0?
Does is still use the same tail cap and cables?
Is the 2.0 going to be phased out. I think I’d still prefer it over the 3.0 because of the longer runtime. Just wish it was dual fuel.
Way better light than a surefire these are unmatched in price and profamance
Dang….. I just got the 2.0 which is freakin’ amazing. But dang.
Cool, but when is that pistol light coming
🔥🔥🔥
Awesome
I’d love to seen a video comparing it to the 3.0 and more information on the light instead of tech.
1300 lumens with 100k candela is insane. Side note can you release the pistol light soon I’m begging you!!! 😭😂
When purchasing this Rein 3.0, does it includes the rail mount , remote switch, battery and a charger? They didn’t specify that into their website ,
Yes.
Interesting, the OKW is already a lightsaber so the idea of having something even more powerful and by this much of a margin is mindboggling. My only concern is the power draw, and the heat management. I am assuming this isn't an LEP so that means we are potentially looking at a lot of heat, and a major power hog, and I am curious how long it will last before it needs to step down.
You are looking at a lot of heat, but then again, this is a weapon mounted application. Much like a suppressor it’s not something you’re grabbing hold onto. We actually thermally regulated this in such a way that you get far superior thermal step downs than what was previously available on 2.0…And because we let the light get hotter, it performs better for longer. Everything I just said he’s not really been spoken about yet in our media, but is upcoming. This is a substantial leap forward.
@@CloudDefensive can’t wait to get one
Should make diving lights!
Yesssssss🎉🎉🎉
Sounds like your running W2 Osram emitters.. Nice!
Not in the 3.0
@clouddefensive. Will this head work on the MCH handheld body?
No. Melty time.
You should make an owl 2.0 with a similar head and dual fuel capability.
ODG? IS THE REIN GEN3 IN GREEN COMING ANYTIME SOON????
Does this mean the Rein 2.0 will get discontinued?
Can I screw the head unto my 1.0 body......Can you please start selling the heads separately. or some sort of an adapter perhaps.
Will the heads be usable on MCHs?
Due to enhanced thermal upgrades, the REIN 3.0 light head CANNOT be used on any MCH lights. Simply, the light head gets too hot which can cause damage to the electrical components.
Is an OWL 2.0 in the works?
Does the 3.0 full size come with the push button tail cap or is that a separate purchase only?
Does the dual button remote switch come with the LCS dual button side plates or is that a separate purchase only?
The Rein 3.0 comes with push button tailcap and a single button remote switch. The dual button switch comes with everything you need including sideplates. It's a direct swap from the single button.
Where's the new pistol light?
Do you plan on selling just the heads, and if so are they fully compatible with 1.0 bodies? Also hoping for more info on new tapeswitches soon
All that info is forthcoming. Hang tight. Long story short yes they are compatible but we have absolutely no expectation on when we would have heads for sale. Demand for complete light systems is so intense we have 100% of our available capacity allocated towards that right now and it will be that way for the foreseeable future.
What’s the damage, and does this mean the 2.0’a price will drop?
400 bones
What’s the price point on these? I have a 2.0 and the dual fuel capability is really appealing.
399.99 for the full system. Everything you need. The most powerful weapon light ever produced.
@@CloudDefensive man that’s really steep, it looks like a good light, but that’s a purchase I really have to think about. Still like my 2.0 though!
My body is so ready
Me too
Price?
Nice to know it can deal with auto suppressor fire
Run time still the same for the micro and full size?
The Micro is not available for the 3.0 Full size only.
@@CloudDefensive appreciate the update.
Are going to offer REIN/Micro 3.0 in handheld?
Our MCH light is the closest equivalent to a Rein handheld. We offer them with various heads depending on your use case with a handheld. The MCH Duty and MCH-HC are most likely what you're looking for. Micros will be available very soon as well.
Currently own the 1.0 full size.. love it.. skipped the 2.0...
Holy sht my body is ready for the 3.0
So am I correct in saying that this was not possible when the Rein 2.0 was being developed?
...I doubt it. The rein 2.0 came out months ago. There’s nothing in this light that didn’t exist years ago. I think they want to keep releasing bigger and better ones for more money. Why would they make the best right away, when there’s people who buy each one because it’s better than the last..?
@@KimballPrecisionRifles well they have been developing the rein 2.0 for quite some time I believe. This video suggests that it wasn't possible previously I would just like that confirmed.
Nice to see ya guys are finally innovating and keeping pace with olight.
😆
_i'm gonna_ *CONSOOOOOOOOM*
Based
whats the battery life vs the 2.0
65 mins with the 18650 battery
You guys are going to make me go broke!! ;-)
I have an OWL as well as a Rein 2.0 and they are impressive to say the least!
What colors will it come in?
My Rein 2.0 is supposed to be in O.D. green but that color does not match my OWL - which is actually O.D. green. (Please go back to the original O.D. green color!)
Only concern is being able to buy just a head. I own a 2.0 and MCH, but still can’t get just a 2.0 head for my 1.0. Will heads be available this time? I really don’t need a whole new light.
exactly this.
tbh the 3.0 isn't going to be worth it for most people who just bought the 2.0 this year or have a 1.0 already,
But selling just the heads would be pretty nice. Especially if you could trade in your 1.0 or 2.0 heads. seems like the 3.0 beats the 2.0 in every way, It basically makes the 2.0 obsolete.
Personally I prefer the 1.0 over anything else despite being dimmer because of the field replaceable lens, heatsink capabilities, and S7 bezel. Really salty that it's not longer available despite them saying it would be.
I'd buy a 3.0 head with those features in a heartbeat. I'm such a small demographic of customers though that I doubt I'll ever see it
I had asked them about a retrofit kit a month back.
In basic terms it was addressed as more economical to just sell the full package vs an upgrade kit
They've had an faq question about it since the 2.0 was coming out, saying a trade in program was in the works and sign up for their newsletter (obviously). Just sell the damn heads already, I'll buy one to get rid of the 1.0 behemoth
@@WeaponizedAutismiii you don’t even need a retro fit to run a 2.0 or 3.0 head. While they were still only making the gen1, they switched from a single coil spring in the tap cap, to a 2 coil spring. As long as you check that your tail switch has the 2 coil spring, you can run any of the light heads. They just have to make them available for purchase.
Will this be compatible with non cloud switches?
No, none of the other switches on the market are powerful enough to get maximum output out of our lights.
@@CloudDefensive Thanks! Any plans on a dual button switch that allows a split connection to a cloud light and something like Peq15? I think that's the main thing keeping me from ditching all my surefire for cloud!
If y'all want to make some money; could you please make a direct competitor to the Streamlight TLR7a? If you could make a comparable sized version that produces 20k candela and still with good spill you would take 5 - 15 percent of their market share, I think.
I hope they do. I just got the x300 turbo in today and it was bigger than I thought . So now back on the prowl for something to fit my p365xl Icarus
Still no pistol light? I can’t drip with mismatched lights, guess it’s back to Surefire
i’m going to use modlite until you guys come out with the 5 or 6.0 lol
How has your Flow556k been holding up?
We have a couple, and they've been fantastic. As you can see, we run them hard haha
@@CloudDefensive I was having trouble deciding between the Flow and Surefire Rc2.
@@bender43718 Both are great cans. I will say though, with Flow, there is no gas drama. It's the best K-sized can I've ever used or seen.
New head or completely new package?
Complete light
I hope you fixed your proprietary crappy pressure switch
100k candela plus being able to use 123's is INSANE... probably going to be switching back to cloud now for this 3.0 lol...
Probably gonna be $400
On your site it just says REIN, is it a 1.0,2.0 or 3.0?? I assume 3.0 but it does not say?
We dropped the numerical naming. All inventory is the latest 3.0 technology. 1.0 and 2.0 have been discontinued.
Guess I'm glad I never managed to snag a REIN 2.0 which has been out for about fifteen minutes.😂 So guys, WTF is up with the OWL? Is it discontinued? It's not on the web site and I've heard nothing. An updated OWL would excite me more than a third version of the REIN (fwiw, I've got an OWL and a REIN 1.0).
Sane here
They were gearing up for the 3.0 Rein release. They will make more OWL's they've told me but didn't provide an ETA. I'm wondering if it will be a OWL 2.0? I love my OWL's!
EPL when?