#DIY
Vložit
- čas přidán 29. 07. 2024
- A video showing how to adjust the slackness of the drive chain in Yamaha Fazer fi / Fz v2.0. Please make sure your chain is cleaned and lubed periodically to have a longer chain life.
Also note that a slacked chain causes a lot of power loss, hence always maintain optimum chain slackness.
FOLLOW ME ON :
FACEBOOK PAGE : / mototechwanderer
INSTAGRAM HANDLE : / mototechwanderer
BLOG : mototechwanderer.blogspot.com/
MY TOOLS (Best & Cheapest) :
Best Heat Gun : amzn.to/3e4OvS7
Budget Heat Gun : amzn.to/2ZGAQLR
Powerful Air Blower : amzn.to/2MwNWFh
Cheap Air Blower : amzn.to/30g92jo
Electric Screw Driver : amzn.to/2BPAUh6
Ring Spanner Set : amzn.to/2U4Ug8Y
Spanner Set : amzn.to/2T1lIIa
Ellen Key Set : amzn.to/2EvPbBn
Surgical Gloves : amzn.to/2SqlYeW
Nylon Mallet : amzn.to/2oKtrN9
Bent Nose Circlip Plier : amzn.to/397PHkU
Steel Screw Extractor : amzn.to/2J0JRHz
Tool Box : amzn.to/2U3cA4K
BIKE ESSENTIALS :
Wind deflector for Suzuki Vstrom : amzn.to/3f813bF
High Temp Primer : amzn.to/3bb17WE
High Temp Paint : Out of stock
Best Engine Oil : amzn.to/3eQQolS
Best Engine Oil : amzn.to/2Bw0Ocj
Good Engine Oil for FZ : amzn.to/30dAZYU
Budget best Engine Oil for FZ : amzn.to/3cEd7Ai
Cheap & Best Bike Headlamp LED : amzn.to/2WsQeur
Car / Bike Portable Inverter : amzn.to/32HOBwF
Phone Charger : amzn.to/2EKnEhZ
Phone / GPS Holder : amzn.to/33H1aZZ
Trumpet Horn : amzn.to/3kh3FHV
1 Watt Pilot Lamp LED : amzn.to/2DIm0x3
0.5 Watt Pilot Lamp LED : amzn.to/3ibDFfk
CAR ESSENTIALS :
Jumper Cable : amzn.to/305qAyl
Car / Bike Portable Inverter : amzn.to/32HOBwF
High Beam Fog Lamps : amzn.to/33ujllt
Low Beam Fog Lamps : amzn.to/2EUIc7F
Phone Charger : amzn.to/31jvVkQ
Trumpet Horn : amzn.to/3kh3FHV
1 Watt Pilot Lamp LED : amzn.to/2DIm0x3
0.5 Watt Pilot Lamp LED : amzn.to/3ibDFfk
MY CAMERA EQUIPMENT :
Main DSLR : amzn.to/3iiNTKS
DSLR Tripod : amzn.to/3ktywS3
External Microphone : amzn.to/3gCMJJX
Action Cam : amzn.to/2PKeTXL
Helmet Mic : amzn.to/2XG2xUS
GoPro Mic Adapter : amzn.to/3ktuOrB
GoPro Case for helmet : amzn.to/2DDVhl8
Helmet Mount for GoPro : amzn.to/2XCOpLS - Auta a dopravní prostředky
You have to move both adjusters back at the same time before you measure chain slack. As you move the other side back you are taking tension out of the chain.
May be the video was a little misleading there but that's exactly how I did it. Thanks for pointing it out.
thank u man ,i was looking for these from so many days i didn't get the correct one , finally u did it ,thank u so much
Glad it helped you 😊🙏🏼
We can also adjust the alignment by simply keeping the tyre at equal distance from the both swingarms!
Yes... But might not always be accurate.
I think better you upload video so we too can learn bro
Thanks for putting this up. Helped a lot!
Glad it helped. Do subscribe to the channel.
Thank you bro, that scale instruments you have made practical.
You're welcome 😊👍🏼
Nicely explained, how to figure out a worn chain or whether i need to change chain sprocket, kindly upload a short video for the same
vishrut shah Surely will do that. Thanks for watching.
Do Subscribe to my channel if you haven't yet.
Thanks, that was really helpful
Rahul NS Thanks buddy. Do LIKE & Subscribe to my channel.
very useful demo for chain slack adjustment. i have a fzs v2
Thank you. Glad you found it helpful. Do consider subscribing to my channel.
@TONY STARK what's so funny buddy ?
Yes very useful.I have v3
@@handersonlyngkhoi7270 thank you. Glad you found it useful.
thanks a lot bro. I finally learnt it. thank you :) please keep uploading such videos 😄😄😄
Glad it helped you. More videos coming up .
excellent..thank u
Welcome 😊
Thanks dude.. Its useful
Nithiyakumar K Glad to know. Don't forget to subscribe to my channel for more such videos.
Great Video. YSC has screwed this up purposely. Have to get this adjusted myself.
Manish Nanda Do it. Take your time. Its easy.
Please do so.
wow thanks bro finally learn it , can u plz tell me what is the best option for chain, among chain lubricant and engine oil
For chain use Tribocor or Motul. For engine oil use Motul or Yamalube.
@@MototechWanderer thanks a lot bro
Welcome
Very nice bro.. helped me alot 💪
Thanks ... Glad to know. 😊👍🏼
Informative
Thank you 😊. Do subscribe to my channel.
Neatly explained.. Thanks a lot..
Thank You.
Same technique on most of the Indian Bike.
purpose solved. but video can be short and no music please. We cannot hear you in that music. Also, you need to follow the process to adjust both adjusters at same length and measure slack.
Thanks 😊👍🏼... Watch the other videos, I hv worked on the audio in later videos.
Nice information bro
Thanks buddy.
is it necessary to tighten the nuts in equal amount in left and right side
Yes. That keeps the balance right.
Otherwise you lost your alignment
love you bro.. i wanted those symptoms of tight chain.. my bike's chain is too tight
Shreenarayan Sabannavar Thanks a lot bro.
Too tight chain makes clattery noise when you ride, start to move from stand still.
Also you get poor fuel efficiency and performance.
Just do the reverse process of what is shown in the video if you want to loosen up your chain slackness.
Shreenarayan Sabannavar Thanks a lot bro.
Too tight chain makes clattery noise when you ride, start to move from stand still.
Also you get poor fuel efficiency and performance.
Just do the reverse process of what is shown in the video if you want to loosen up your chain slackness.
Your video is very detail and nice.and i would like to know if you have any idea about oil in the front disc brake.last evening i saw some oil drip from the front disc brake of my bike after taking my bike for practice .mine is an old fzs 2012 model.please answered at asap
Thanks a lot!
Check if the bleeding screw is tightened or not. Also check of your fork oil seal is leaking and the oil is dripping.
Have u ever done tappet tuning of your bike.... ,If u had done already can u make a video of it ...my bike has no tappet noise yet but there is a small noise from engine head and I think valve is quite losse ... if u have any opinion regarding this ....
I have done it once. Will make a video soon.
@@MototechWanderer waiting in anticipation
Sir iam having fz new one bs4 model i have one problem that when we go to potholes the bike sound very bad because of the chain touch rubber i serviced chain. Then also it making sound.Then i have placed hitlon it is wearing fast what to do for this problem???
Rahul Biker just check if chain guide (the rubber part) is in good condition or not. If needed replace the chain guide. Adjust the chain a little more so that it doesn't touch swing arm on potholes.
Mototech Wanderer thanks sirr
Brother video super & People Don't trust Yamaha technicians ENGINEERS they are unfit for Technical ENGINEERS use this brother technique for more life span of chain & sprockets wheel
Thank you brother. 😊
Thanks this is good demonstration
Thank you. Do subscribe to my channel for more DIY videos.
Is it fine to tie axle nod after test drive Bro?
@@handersonlyngkhoi7270 I would not suggest to test drive without tightening the axel nut. You don't need to tighten it 100% while test drive. Once it's final, then tighten it fully.
what size spanner did you use?
Watch from the beginning, everything is explained.
I cant able to loose the axile nut itbis very tight...please give me some idea to loose the nut
lovely ashwa get it loosened by a local mechanic. Also try spraying WD40.
Hello bro....can u put a video on how to get free clutch play on fz150...thanks
Rougeot Luccas Sure. Will do that. Thank for watching.
Hi could you upload a video to change the RPM of FZ Fi. Thnk you
Sure will do that as well. Thanks for the suggestion. Do share and subscribe.
Can fz do that or its just 4 gixxr 150
czcams.com/video/zuiJKaTzQlo/video.html
Upper side of chain touches a rubber thing know
That's the drive chain guide. It's normal.
Sir there is a plug near gear shifting peddle what is it for?
Irfan Sofi That's a magnetic switch which senses Neutral .. and displays the N light on the speedometer console.
Motorway Wanderer sir my bike chain is tight in neutral but when i shift gears it loses with each gear . what to fo?
May be chain is reaching the end of its service life. Might need a replacement.
How can we reduce chain noise in FZ.
I have changed chain and sprocket recently. But after few days, I can see chain sound again. I will clean the chain every 300km and lube it with gear oil.
Can anyone tell me how I can reduce chain sound.
Try adjusting the slack and check for wheel alignment. Use silicon based chain lube.
@@MototechWanderer Thank you for your reply. Previously I was using silicon based grease but still same sound. Hence, I switched to gear oil
I have done as it as done .but the stripes on frame is not equal is there any problem. or danger with that!!
I'M A dukerr it is missalligned
There can be a little mismatch in the markings, a little here and there would not make much of a difference. If its too confusing, you can use a scale of measuring tape to get correct measurement on both sides.
Hai bro please can u show me one's change my bike Thayer from that I get problems back brake suggest me easy method bro please R15 V1
Will try to make a video.
helpful
Thank you
sir i also have fazer v2 and i suffering from the chain noise issue in 3 gear slow speed . i observed that you removed the lower fibre part from chain . is that helps to reduce noise ?
i adjusted chain slacks but after 1 2 weeks noise keep coming
Your sprockets are gone mostly. It calls for a replacement.
@@MototechWanderer same thought come into my mind so i changed it mounth ago but still not fix it
Really helpful brother👍👌
Joseph Samuel Thanks a lot. Don't forget to subscribe to my channel.
Mototech Wanderer Bro I am already there in your subscribers list😊
Joseph Samuel Great. Thanks again.
Bro my bike is fzs v3. It's chain is tight, can i loose it by myself instead of taking it to a mechanic....?
Yes. Absolutely. Do it yourself.
👍👌
the Chain seems to be really clean how much clean this much at 15k kms
Shivansh Batham I had thoroughly cleaned the drive chain using kerosene and tooth brush.
Yamaha Fazer dude even after doing this after few days my chain is back again loose! what should I do?should I entirely change my chain socket? pls reply
Its unfortunate how bad the quality of chain is on Fz v2.0. You can also fix Fz v1 chain Sprocket set , it will add a little more top end. Cannot comment on the durability of the chain.
is there any effect on mileage after changing fz 2.0 chain sprocket with older version fz16. because fz 2.0 has 42Tooth sprocket
@@biprojithmandal2011 you should get higher mileage
What's the size of lock nut & slack adjusting nut of FZ V3?
Plz reply
Size 12mm both
Thank u
@@gijopjacob1985 you're welcome buddy.
good
Thanks. Consider subscribing to the channel.
bro What is the wrench size of rear wheel bolt?
17-18mm AFAIK
@@MototechWanderer mine is v3 bro. I went to mechanic shop he given me the spanner it's 22mm. Maybe 17-18mm is for v2. Anyway thanks bro
@@adityapeeta4865 okay👍
bro if install rear disc break how much cost?
15-20k easily ... Swing arm, rims, forks, calipers, disks needs to be changed too
@@MototechWanderertq fr reply bro...its too costly
Fazer breack how to chake
There is a notch on the brake plate. That shows the shoe life and wear.
Greatt
Thanks
very clear and informant tutorial nice job man i badly need to alling my chain thnx
mekash singh Thanks buddy :)
Do subscribe to my channel if you haven't yet.
Yamaha Fazer dude my fzs has no lock nuts on both side. what now???
mekash singh can be bought in any hardware shop.
How to decrease chain slack
Watch the video. Everything is explained in this video.
rear sprocket teeth????
41 Teeth
Every rider should know some basic repair work. I learnt something useful today. Thank you.
Kapil Hazarika well said. Happy my video helped.
Thanks. Consider subscribing to the channel.
Neat :)
Thank you :)
Thank you bro.
I need to adjust every week, I don't know why?
Either not properly lubed and cleaned or the alignment is incorrect.
@@MototechWanderer this happen after the mechanic change the sprocket
@@DikaKhawlhring something is not right. Was the kit used original Yamaha part
I have to adjust after every 20 30 kms 😂😂
@@gpame265 😂😂
nice info. only one request please speak lil louder.
rowdy rathod sure Buddy. Working on the audio. Watch the recent videos.
Why do you had to put the useless music at the background. We can harldy hear your voice. Either be more audible or remove the unnecessary background music. Pleaseeee. haath jodta hun.
Ok sir. I have worked on the audio of my videos. Please check the rest of the videos and let me know if they are fine or not. Thanks for the criticism. It help me improve.
Bhai bo Kansas Book hai
User/ owner manual
Purpose of change bro..??
It's a slack adjustment video.
How to loose chain
The reverse process of what I did ... Adjustment bolt to be rotated conter clockwise.
Kk
My chain touching swingarm noise what to do losing or tightening
@@eu_sou_arun tighten the slack to correct value. Also check if the chain guide (rubber) is present and in good condition.
@@MototechWanderer chain ruber good condition
Use proper tools. You damage the axle nut. Better to use ring spanner 6 point
True. I have bought it now.
@@MototechWanderer what size is that bro
were u talking to ur self??????
Was trying to talk to my viewers buddy. Somehow the sound capture did not turn up well. Sorry for that.
Why don't you try to use earphones, it will help.
Thanks for watching. Do subscribe to my channel if you have not yet.
Yamaha Fazer Yeah actually the video quality s damn good but the audibility is weak! keep it up being much more videos
thippu thippesh Thanks a lot buddy. Your appreciation keeps me going.
Will be making more such videos and try to record better sound.