Wish I’ve found your video sooner. I’ve got the same exact unit and thought this was the issue, so your replacement part being available on Shopee really helps ! Thanks for sharing!
*We liked it **Fastly.Cool** so much in the basement, we bought a second one for the main level. The amount of moisture it pulls out of the air is astonishing.*
Thanks buddy this was the same fix for mine too. I got my ultrasonic 20mm from amazon. Came in pack of five cost about $13. So a $2.60 piece caused so dilemma. Saved me my $130 humidifier. Had in garage ready to dump it into recycle electronic. Pheeewww...
I didn't have to replace the ultrasonic plate on my Anjou diffuser, all I did was take it apart and wipe it down with alcohol and it started working like new.
Being doing the same thing almost for 10 years now. 😂 Wipe with alcohol and it's good as new. The only thing that broke down during that time was the fan, and that was replaced. Changing the ultrasonic unit isn't a long term 'solution', because this sort of issue keeps happening due to water quality.
Ang sa akin po ay pag pindotin ko ang on switch mag beep once lang pero ayaw umandar. Pero kun pindotin ko ang light switch mag ilaw cya pero walang mist.
Very good video, I have the same problem. I am measuring the voltage on the old mist maker, but am getting O. Would you know if there is supposed to be any voltage at the mist maker, where the two wires are connected to the round white mist maker? I am getting voltage to the circuit board. But do not want to spend money on a new ultrasonic mist maker if the circuit board is shot and not providing current to the mist maker. I tried AC and DC and get 0 amps, volts, 0 anything. Unless when the mist maker is shot it has no current going to it. I cleaned everything else up and have tried getting it going. Thak you in advance.
How did you find out it was a 20mm part ? I have a MH-903A - Air Innovations Humidifier ultrasonic one but it has a black right (not rubber ) around it
How is mist increased when putting on higher setting? Is a longer pulse sent to the diaphragm (ie. lower setting, diaphragm is off longer)? Does the droplet size change with the output setting?
I think the mist is not vary because they rely on frequency applied and those frequency is not change. Mist can be adjusted by the air coming from the fan which pushes the mist.
If you have a multimeter, you can measure the output voltage of the terminal. Just turn on the humidifier af adjust the knob then tap the probe on the two terminal. You can easily determine where is the positive and negative
Mine has stopped working too. Fan is ok, led is ok, and even i can see the water vibrating above the piezoelectric atomizer but it is not making mist. Is it still possible that the atomizer is bad? Maybe it is not completely bad, it is working some way but not correctly?
My daughter has this exact one and it keeps leaking as soon as I turn it on. Any suggestions??? This is the 2nd one to do this and I’m fed up, but my daughter really likes it.
Sir good day po Same din tayo ng unit kaso ayaw p rin mg mist sa akin. Hindi man lng kumukulo. Kakapalit ko lang bago mist maker Any advice po? Salamat at Godbless
Kung no power po possible sa electronics na ang sira. Pwede niyo po ipacheck sa mga electrician. Or kung kaya niyo po check niyo po baka may natanggal lang na wire
Sir Mera Agaro humidifier switch on krne pr ON nhi ho rha maine voltage check kri voltage aa rhi Hai kya problem ho sakti Hai abi 3 month hoye Hai purchase kre hoye
Ginamit ko kasi sya kanina umusok naman then i tried ilipat sa kwarto tapos hindi na sya nag i steam . Working naman yung mist and all idk bakot di lang umaabot sa top yung usok bigla
sir tanong ko lang po, nung inON ko po may power naman, pero walang mist, and kahit nung inopen ko and inON walang bubbles like nung sa video nyo.ano po kaya ang problem? tnx and God bless.
@@DrixWorks 16mm po is sakto lng . ang hndi sumakto e ung wire .1.5-3w ung naorder ko mnipis ang wire . ung tinanggal ko na mistmaker is ung white ay mnipis ung isang wire ay mejo mkpal .tingin nyo po anung (mm)&(hertz) kya ang fit sa humidifier. ko . syangnmn kc ko bbili pa bago .
Sir ganyan din po yung humidifier ko, kaso yung sakin umapaw po yung tubig at gumapang sa baba yung tubig hanggang nabasa yung loob habang naka-on. Tapos nag amoy sunog na siya sir. Repairable pa po kaya yun sir?
My original intention for this humidifier was to use it for plants that require high moisture levels. After using it in my room, czcams.com/users/postUgkxtD9aJ2m6GU-X1IChQxjn9l31K1A7Kpwj however, I think that's where it is going to stay in the fall and winter season at least. The increased humidity in my room made the room warmer and more comfortable. I had first ran the humidifier for 4 hours with the timer setting for it. After the first hour, I checked my room and can feel the difference. When the full 4 hours was up, I checked again and noticed that the humidifier was shut off as it is suppose to. The moisture level never seem to get passed 56/57%. I then let it run until all the water is used up, which it wasn't all used up. There are still some left in the base that you are not suppose to add water to. I filled up the water tank all the way again, being careful when removing it from the base. Some left over water may spill out. After putting it back on and setting the unit to auto, I let it operate. It didn't stop running, rather I don't know if it did at any point since I didn't check it regularly, for 24 hours after which the water in the tank ran out. The moisture reading never passed 56/57%, which may be a good thing for me. Being situated right next to my bed, the noise was not very noticeable with the occasional water gurgle from time to time as the unit ran.
Oo sir napansin ko rin yan. Actually dalawa kasi yung gamit namin na humidifier. Kinuha ko mist maker nung isa yun triny ko dun sa mahina bumuga. Tapos yun dun na ko nagconclude na mist maker talaga sira
Opo para maihinang sa terminal. Pero kung wala po kayong soldering iron pwede niyo naman po icut nalang yung wire tapos dun niyo nalang pagbuholin. Tapos lagyan nalang po electrical tape
Boss paano kong tatlong piraso ung ganyan...kasi nabiyak ma lasi ung tattlo lumalabas tubig sa kakalinis nang kasama ko nabiyak..20mm naman sukat niya sir..puwede kaya yan doon ...or lahit anong klase na ganyan basta 20mm sukat
Drix' Works san po kayo banda sa La Union po? Ayaw po kasi gumana ng humidifier po namin. 😥 bagong bago palang po. wala pang 1 week na nagamit po, 3 days lang nagamit tapos after 1 week po nung ggamitin na namin ayaw naman na po gumana. bglang nagflicker lang ung ilaw nung sinaksak po namin sa extension tas wala na po
For me its a quick fix. Its not even complicated if you followed the procedure. My motive is to help people with same problem. Sorry if I did not meet your expectation
Like and Subscribe to my Channel! Thank you! 🙂
Sir saan nakakbili nyan ultrasonic katulad ng kinabit mo PA order namn poh
@@jedlesterluna3564 sa shopee sir. Nasa description po ng video yung link. Bawal kasi magcomment ng link nabubura
sir same lng po tau ng humidifier my sukat p po b yan
@@appleajon3922 yes po 20mm yung sukat po nung mist maker
Wish I’ve found your video sooner. I’ve got the same exact unit and thought this was the issue, so your replacement part being available on Shopee really helps ! Thanks for sharing!
*We liked it **Fastly.Cool** so much in the basement, we bought a second one for the main level. The amount of moisture it pulls out of the air is astonishing.*
Thank you!
Why the need to transfer the rubber seal from old to new mist maker ?
Is it not advisable to use the newer rubber seal ?🤔
Thanks buddy this was the same fix for mine too. I got my ultrasonic 20mm from amazon. Came in pack of five cost about $13. So a $2.60 piece caused so dilemma. Saved me my $130 humidifier. Had in garage ready to dump it into recycle electronic. Pheeewww...
I didn't have to replace the ultrasonic plate on my Anjou diffuser, all I did was take it apart and wipe it down with alcohol and it started working like new.
Thanks for the input. But its better to replace it to work perfectly
Being doing the same thing almost for 10 years now. 😂 Wipe with alcohol and it's good as new. The only thing that broke down during that time was the fan, and that was replaced. Changing the ultrasonic unit isn't a long term 'solution', because this sort of issue keeps happening due to water quality.
Worked like magic. Thanks
I think I have the same problem but have no idea how to start. This was a great informative video
Thank you! Just follow what I did
Nice video. Mas maganda pala ung ganyang model na walang filter stick!
Thank you sir! God Bless
hi is it normal to get shock when i touch the white damper area when the device is on? cause im afraid it might have electric leak
I think it is not electric shock sir. It is the vibration produced by the mist maker
Ang sa akin po ay pag pindotin ko ang on switch mag beep once lang pero ayaw umandar. Pero kun pindotin ko ang light switch mag ilaw cya pero walang mist.
20mm 2.4Mhz Ultrasonic Mist Maker Fogger Atomizing Transducer
pwede b yan sir?
parehas tayo ng model ng humidifier pati board
Very good video, I have the same problem. I am measuring the voltage on the old mist maker, but am getting O. Would you know if there is supposed to be any voltage at the mist maker, where the two wires are connected to the round white mist maker? I am getting voltage to the circuit board. But do not want to spend money on a new ultrasonic mist maker if the circuit board is shot and not providing current to the mist maker. I tried AC and DC and get 0 amps, volts, 0 anything. Unless when the mist maker is shot it has no current going to it. I cleaned everything else up and have tried getting it going. Thak you in advance.
How did you find out it was a 20mm part ? I have a MH-903A - Air Innovations Humidifier ultrasonic one but it has a black right (not rubber ) around it
How does one clean the fan once open the body?
20 mm what is frequency
Can you please tell if i can switch a 2.4mhz to a1.7 mhz ,using the same board controller?
How is mist increased when putting on higher setting? Is a longer pulse sent to the diaphragm (ie. lower setting, diaphragm is off longer)? Does the droplet size change with the output setting?
I think the mist is not vary because they rely on frequency applied and those frequency is not change. Mist can be adjusted by the air coming from the fan which pushes the mist.
Thank you for making this video!
How would i know if i place it correctly? I almost forgot where is the right terminal..
If you have a multimeter, you can measure the output voltage of the terminal. Just turn on the humidifier af adjust the knob then tap the probe on the two terminal. You can easily determine where is the positive and negative
Mine has stopped working too. Fan is ok, led is ok, and even i can see the water vibrating above the piezoelectric atomizer but it is not making mist. Is it still possible that the atomizer is bad? Maybe it is not completely bad, it is working some way but not correctly?
I think the ultrasonic misk maker is the problem buddy. It is still working but not working very well
same like mine
My daughter has this exact one and it keeps leaking as soon as I turn it on. Any suggestions??? This is the 2nd one to do this and I’m fed up, but my daughter really likes it.
Be sure to tighten the screw sir when placing the ultrasonic
How many operating voltage of this device ?
is all humidifier are the same?
Sir good day po
Same din tayo ng unit kaso ayaw p rin mg mist sa akin. Hindi man lng kumukulo.
Kakapalit ko lang bago mist maker
Any advice po?
Salamat at Godbless
thanks for this!..kung ano anu na kinalikot ko yan pla ung sira kaya diko maayos ayos..hehe thanks!
Thank you po. Hehheh
Link for part not working
boss same po ata tayo. Yung akin, gumagana naman kaso sobrang hina ng binubugang mist. Miskmaker po ba tlga ang problem?
Yes po. Try niyo po palitan mist maker
Hi
excellent explainer video thank you very much
You're welcome buddy! Thanks for watching
Link shopee is broken..!
yan mist maker na inorder mo pwede kaya ikabit sa maliit na humidifier na 5volts usb type lang
Hindi ko lang sure boss. Basta magkasize siguro yang mist maker pwede
20mm size nung ultrasonice mist maker na ginamit ko boss
Hi sir saan ko po pwde ipagawa yung humidifier ko? Tagal na kase na stock di nagana
Sir paano pag yung fan dna umiikot mya mbibili kaya fan? Paano po irerechecm
Posible kayang ganyan din problem ng sa amin . Kasi no power halos yung amin.walang light..pwede po kaya iyon gumana ulit.. thanks sa response
Kung no power po possible sa electronics na ang sira. Pwede niyo po ipacheck sa mga electrician. Or kung kaya niyo po check niyo po baka may natanggal lang na wire
@@DrixWorks Thank you so much sir .. more subscribers to come
@@npab05 thank you sir! God bless!
Paano po pag pinalitan na ng ultrasonic (2x ng pinalitan ng bago) pero hindi pa rin po nagpoproduce ng usok? Ano po need i check?
Yung mist maker po ang 2x pinalitan wala pa ring usok.
good job 🙏💫
Sir Mera Agaro humidifier switch on krne pr ON nhi ho rha maine voltage check kri voltage aa rhi Hai kya problem ho sakti Hai abi 3 month hoye Hai purchase kre hoye
Same problem with me agaro
Ser pareho tyo ng humidifier ung akin umiinit nung binuksan ko ung ultrasonic nya
Natural lang na uminit sir. Pero pag faulty na kagaya sa video pwede niyo na po palitan yung ultrasonic
How can be this fix is quick if you had to order a part?
Quick fix refers to the repair itself 🙂
Hi po pag malaki po ba ang water capacity (13 liters)mas malaki din ba ultrasonic mist?
Hindi pa po ako nakapag baklas ng ganyan kalaki na humidifier pero yes po mas malaki for sure mist maker niyan.
Hello po. Yung akin po ay automatic na nag-oon and off. Ano kaya pwedi gawin? 🥲
Yung mismong power na po ba ang nag on off? Or yung ultrasonic mist maker lang?
How about po na bigla syang hindi nag i steam . Umuusok naman sa baba peeo di sya nag rereach sa top thankyou
Possible po na yung ultrasonic din ang sira maam
Ginamit ko kasi sya kanina umusok naman then i tried ilipat sa kwarto tapos hindi na sya nag i steam .
Working naman yung mist and all idk bakot di lang umaabot sa top yung usok bigla
Triny niyo na po tanggalin tubig then lagyan po ulit?
Yes po sir. Pero ganun padin doesn't reach the top para sa usok
Try niyo po magsend ng vid sa fb page ko maam. Check ko po. Nasa description po yung link
sir tanong ko lang po, nung inON ko po may power naman, pero walang mist, and kahit nung inopen ko and inON walang bubbles like nung sa video nyo.ano po kaya ang problem? tnx and God bless.
Possible mist maker na talaga yan sir kagaya nung pinalitan ko po. Totally di na nagwowork yung ultrasonic nun sir
Paano malalaman kung buo yong nabili mist? Pede gamitan nang tester?
Di ko sure kung pano itest sir. Try niyo nalang po ikabit sa humidifier kung gumana
Boss paano ko po kaya malalaman kung anong size ung bibilhin ko? Halos same issue po. Wala po masyado nalabas na mist.
Measure mo gamit ruler sir. Yung rubber seal po ang imeasure nyo
sir pnu ko po mllman kung anu fit na transducer mist maker sa humidifier ko ? mli po ata ung nbli ko di nagana.
Sukatin mo muna sir. Magkakaiba kasi size niyan
@@DrixWorks 16mm po is sakto lng . ang hndi sumakto e ung wire .1.5-3w ung naorder ko mnipis ang wire . ung tinanggal ko na mistmaker is ung white ay mnipis ung isang wire ay mejo mkpal .tingin nyo po anung (mm)&(hertz) kya ang fit sa humidifier. ko . syangnmn kc ko bbili pa bago .
@@mielgomez1283 di ko kasi mavisualize sir. Pm mo sakin sa page ko sir. Nasa description page ko
Sir ganyan din po yung humidifier ko, kaso yung sakin umapaw po yung tubig at gumapang sa baba yung tubig hanggang nabasa yung loob habang naka-on. Tapos nag amoy sunog na siya sir. Repairable pa po kaya yun sir?
Sira po siguro yung floater niyan kaya umapaw po. Try niyo po patuyuin muna tapos saka niyo po buksan
@@DrixWorks totoo po bang pag nasunog daw yung nasa loob hindi na daw po magagawa?
@@allenjoshua4651 kung yungmismong board na po ang nasunog di na po magagawa
@@DrixWorks thank you so much po sir
ok po ba 16mm sa ultrasonic
Sukatin mo nalang sir kung gaano kalaki yung ppalitan mong ultrasonic pra sigurado
My original intention for this humidifier was to use it for plants that require high moisture levels. After using it in my room, czcams.com/users/postUgkxtD9aJ2m6GU-X1IChQxjn9l31K1A7Kpwj however, I think that's where it is going to stay in the fall and winter season at least. The increased humidity in my room made the room warmer and more comfortable. I had first ran the humidifier for 4 hours with the timer setting for it. After the first hour, I checked my room and can feel the difference. When the full 4 hours was up, I checked again and noticed that the humidifier was shut off as it is suppose to. The moisture level never seem to get passed 56/57%. I then let it run until all the water is used up, which it wasn't all used up. There are still some left in the base that you are not suppose to add water to. I filled up the water tank all the way again, being careful when removing it from the base. Some left over water may spill out. After putting it back on and setting the unit to auto, I let it operate. It didn't stop running, rather I don't know if it did at any point since I didn't check it regularly, for 24 hours after which the water in the tank ran out. The moisture reading never passed 56/57%, which may be a good thing for me. Being situated right next to my bed, the noise was not very noticeable with the occasional water gurgle from time to time as the unit ran.
Sir umiinit din ba yung unit mo nung nag start humina yung mist?
Oo sir napansin ko rin yan. Actually dalawa kasi yung gamit namin na humidifier. Kinuha ko mist maker nung isa yun triny ko dun sa mahina bumuga. Tapos yun dun na ko nagconclude na mist maker talaga sira
Nice. Salamat sir!
@@NapoleonBorn2Party thank you rin sir! Sana nakatulong heheh
Sir need po tlaga may soldering iron?
Opo para maihinang sa terminal. Pero kung wala po kayong soldering iron pwede niyo naman po icut nalang yung wire tapos dun niyo nalang pagbuholin. Tapos lagyan nalang po electrical tape
Boss ano problema pag Walang power or bigla nalang Di nag on. same humidifier tayo boss.
Check mo yung power cord sir baka putol. Hindi ba umiilaw led niya sir pag ino on?
Sakin din ayaw mag ON bigla, walang ilaw ung led lighy.
@@KimNario check mo muna yung power cord sir baka putol
Boss same fix rin kaya to sa akin? Bigla nalang kasi walang mist na lumalabas eh. Di ko mabaklas yung ilalim 'cause wala akong pang hinang
Possible boss. Pero pag inon ba parang nagbabubbles naman? Gaya nung sa vid
@@DrixWorks Yes boss gaya ng sa vid. May recommendation ka ba ng pang hinang tools na mura mura?
Meron naman mura na pang hinang boss. Kahit 30W soldering iron pwede na. Less than 150 lang ata yun
@@DrixWorks Thank you boss! Nang dahil jan, subscribed na ako!
Thank you boss! Malaking tulong yan hehehe
Boss paano kong tatlong piraso ung ganyan...kasi nabiyak ma lasi ung tattlo lumalabas tubig sa kakalinis nang kasama ko nabiyak..20mm naman sukat niya sir..puwede kaya yan doon ...or lahit anong klase na ganyan basta 20mm sukat
Same lang siguro sila ng frequency boss. Basta same sila ng sukat pwede yun
Anonung pagsukat sir ung pinakaloob ba nang bilog na walang rubber or ung mismo na nasa labas na rubber ang isukat ko..
Kasama yung rubber seal sir. Outer diameter nung rubber
Ang sinukat ko kasi tinanggal ko ung rubber at yung matigas na bilog un ang sinukat ko..20mm siya
Mas malaki nga siguro yan sir. Kung may rubber seal ano sukat?
Anong sanhi bat fi na nagaba yung mist?
Over usage na rin po siguro
Saan po ang shop niyo atsaka magkano po aabutin kung ipapaayos ang humidifier? Salamat
La union area po ako. Libre lang po kung sakali. Try niyo nalang po yang tutorial ko heheh. Kaya niyo po yan
@@DrixWorks ay sayang, huhu. Akala ko dito lang kayo sa Manila. Nice video and thank you. Yep, will follow along your tutorial.
@@sarutobihokage7488 thank you rin po. God Bless!
Drix' Works san po kayo banda sa La Union po? Ayaw po kasi gumana ng humidifier po namin. 😥 bagong bago palang po. wala pang 1 week na nagamit po, 3 days lang nagamit tapos after 1 week po nung ggamitin na namin ayaw naman na po gumana. bglang nagflicker lang ung ilaw nung sinaksak po namin sa extension tas wala na po
Bangar la union po maam
Hi ! Would 16mm still works for that unit? We have same model of purifier..
Normally 16mm nakkta ko na local ... the rest 20mm from china pa
Not advisable po. Kasi baka tumagas sa ilalim masira pa po yung board. Mas better na yung sukat nalang po ang sundin para walang problema
na try ko na ok lng lakas nga ng mist eh
@@jheriantv9094 16mm po nilagay nyo? diba maliig sukat nun? dikaya masunog dahil maliit ang wire
Saan po mabibili yung pinalitan ninyong sira? At ano po ang pangalan?
Nasa description po yung shopee link nung item maam. Di po kasi pwede magcomment ng link dito
@@DrixWorks salamat po
@@rizajuangco9028 most welcome po
Mist maker or difusor ultrasónico.
where is the quick FIX? this is a component replacement.
your blog title is deceiving, the motive is to earn views. frustrating.
For me its a quick fix. Its not even complicated if you followed the procedure. My motive is to help people with same problem. Sorry if I did not meet your expectation
Ano po un order m shopee
Nasa description po yung link
hii, ask ko lang po kung magagawa pa po ba yung akin nabasa po kasi yung pinakaloob nagkamali ng lagay ng tubig. thank u
Kung nabasa po yung loob. Patuyuin niyo po muna. Tapos once natuyo na try niyo po ulit isaksak kung gumagana
@@DrixWorks Hello. Mukhang ganun nangyari po sa amin. If di po gumagana kahit natuyo na, sira na?
@@ey.molito check niyo po muna kung may power. Kung umiilaw po pag in on pwede pa. Kung hindi po umiilaw possible may nagshort circuit na po
@@DrixWorks thanks sir! Working na ulit :)
@@ey.molito good to hear po. Most welcome! :)
ssir mag kanu po ung parts
46 pesos po ata. Sa shopee ko po nabili. Tignan niyo po sa description andun yung link
what
awit un pala ung nagproproduce ng mist binutas ko tpos di na gumana shet
Palitan mo nalang sir. Heheh
@@DrixWorks sir yung akin naga blink ng blue sa switch at red sa loob ng tank
Rooster 4:02
Sir ask ko lang po yung akin po naga blink sya ng red sa loob at sa switch ng blue continues
Di ko pa po naencounter yan. Wala naman po bang tagas yung tubig?
@@DrixWorks wala sir
Pwede ba sa JML HUMIDIFIER YAN?