Replacing Rotors with Tapered Roller Bearings - EricTheCarGuy
Vložit
- čas přidán 25. 08. 2024
- Replacing Rotors with Tapered Roller Bearings - EricTheCarGuy
I thought I would try putting the website link first this time. I was very happy to make this video since I don't often see tapered roller bearings anymore. This video shows the step by step process of removing tapered roller bearings, cleaning them, and repacking them. I have thrown in a few tips and tricks that I hope will make the job easier and given you a list of tools that you will need to get this job done. I hope you have as much fun watching this video as I did making it.
You can visit me at the web address link at the top of this description.
---
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
ericthecarguy.com/
Visit EricTheCarGuy Forum
www.ericthecarg...
Visit my Facebook Page:
/ ericthecarguy
---
Stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
Thank you Eric. I love these old videos.
Your videos have helped , and inspired me over the years. It has been pivotal in changing the course of my life for the better!
Eric, your videos are terrific. I'm the mom of a disabled (adult) child with health probs of my own. In my spare time, I started watching you a while back on my phone, computer, or ROKU. Since then, you've saved me I don't know how much trouble and money. Your concise yet thorough explanations and good use of a camera are very appreciated!
Bro,Ten years later &still the best vid on CZcams
Thanks Eric you saved my life….That little trick of removing the bearings was critical. Love your insights 👍
Seriously! Your trick to get the back bearing out was genius. Thank you.
Wanted to say thanks for making this video. I have a 94 Lebaron Conv that needed new bearings and I couldn’t figure out for the life of me, how to remove them from the hub assembly. I rented a press, posted on a bunch of forums, etc and no one explained it like you did. I followed your tips and they came out with almost no problems at all.
This vid merited me becoming a subscriber. I recently got a 1973 Ford F250. After its OE died, it sat in the garage for 10 years while his kids fought over it. Finally, the mother had had enough. She called the local garage and told the guy that if he picked it up that day, he could have it for free. It's a beautiful truck, but after replacing all rubber/gaskets, it needed brakes. Mechanic told me 1300 for pads, rotors/drums--you changed that plan! I did the whole system for less than 500. THX!!
Just had to rebuild all my brakes last weekend. 94 dodge ram. Havent had to do bearings in years. You never really forget it though. Love the videos. Keep it up.
Thanks EricTheCarGuy, this video, like many others of yours have greatly helped and educated me! Just did my inner and outer front wheel tapered roller bearings on my '99 Mitsubishi Canter. It was daunting at first, to do a job I've never done before, not a mechanic but i'm eager to learn and do jobs myself.
This brings back memories of my dad teaching me this at about 12 years old. I have an '89 Trans Am GTA that's mine and I'm doing the same exact thing on. Thanks for the video and bringing back fond memories of my dad teaching me how to work on cars!
Been watching for about 5 yrs. Doing my front brakes soon. You are the "Only one" of about 200 YT brake vids I've watched that explain which direction the grease seal goes. I have been known to not get it right. Great detail on this one.
@EricTheCarGuy My first real car was an Olds 88 with that style of brakes and being a teenager, I had to learn to improvise. I like the way you adapt because not everyone has the "right" tools. Yet you still do your job in an even tempered, professional manner.
Thanks for this. I started to do brakes and rotor on a relative's GMC van today and was surprised to see a setup like this. I wasnt confident to proceed, but now I know what to do. Thanks for all the details and advice..
Amazing video Eric. I've gotten a 1975 mustang 2 and I'm going to replace the rotors and drums(drums look original, maybe rotors too) and I've never done these kind of bearing or rotors before and this video is perfect for a first timer. It looks like these old style bearings are actually a million times easier to replace than newer ones.
Hey Eric just wanted to say thanks for the video, I just replaced the front rotors on my Blazer and without this video I would've had no idea whatsoever on how to do it but with your video I was able to get it done. This is my first car so I'm still learning, just once again thanks for all the great videos.
I read a procedure for preloading bearings in an owners manual long long ago (I'm 77). Use a torque wrench and tighten castle nut to 80 ft/lbs, the wheel won't turn, back off, turn the wheel, then retighten to 20 ft/lbs, wheel will rotate but it will be tight, loosen castle nut to next available cotter pin slot and install. It is important to rotate the wheel when doing this and note if there is any binding, this would indicate the bearing wasn't seated squarely most likely is cause by the outer race not being fully seated. In the end, the wheel should rotate without any drag with very little play in the bearing. At most you will go back to the second available slot for the castle nut. In any case I really don't like this combination of rotor and hub in one assembly, hubs can last the life of the vehicle, rotors have to be replaced after a couple of brake jobs. The one advantage is that it forces the mechanic to check and grease the wheel bearings.
What you're describing must have been for adjusting ball bearings, not tapered roller bearings. I don't know what kind of car your manual was for, but It seems a bit extreme even for ball bearings. I have the 1957 Chevrolet shop manual, when ball bearings were in use, and the torque is 33 ft/lb for them, then back off enough to insert the cotter pin. It never says to torque to 80 ft/lbs at any time. Tapered roller bearings started being used in Chevrolets around 1962. Roller bearing adjustment is totally different from ball bearings, and should not be adjusted like ball bearings or damage will occur to the bearing. When roller bearings are properly adjusted, they will have no pre-load on them, and will not even be finger tight.
I'm thinking most guys watching this video are trying to save some money , so why change a good bearing , a properly set bearing will last the life of the car just replace the grease as it gets contaminated m and worn out by use ..Eric does a great job in showing how most guys can do these jobs in their garage without too many specialty tools .
Industrial machinery running constantly can have bearings last 10 years with proper maintenance , compare that to your car .
Been scared to do bearings on my 91' S10 but this vid made it so easy! I wont hesitate to do it now! THANKS!!!
Just wanted to say thanks so much for the video. It was very informative and left me without any questions. I'm a new school car guy that is in love with his older GM. Felt stupid to ask this type of question on the forums.
Hey Eric, awesome video! I work for a bearing company and the only thing I would add would be to get clean gloves when applying the grease on the bearings, as dirty gloves contaminate the new grease! Other than that everything was beyond exceptional
@eurotrashcc Glad the video helped, thanks for the comment. This is actually one of my favorite videos.
I just watched the whole video as I do to most Eric the Car guy videos - I don’t even own a GM - but love learning something new! Such a wealth of info provided by Eric’s videos over the years ! We are very lucky.
Gotta thank you again Eric. This worked on my 1995 Buick Roadmaster. Did both sides with little complications and I'm rolling again!
@1Whatup8 Thank you for taking the time to leave such a great comment.
Great video. Saved me on my wife's 98 suburban at midnight on a workday. Keep it up, stay dirty.
Both my 1997 Ford F-150 and 2008 Ford E-350 uses these tapered bearings. Never dealt with these type of bearings before but you're video saved me lots of time and prevented mistakes! Thx!
@Harrrri82 Glad you liked it, thanks for the comment.
I'm only new to this channel, I'm looking to start my trade soon as a Heavy Vehicle Mechanic in the army to pursue my interest in Auto mechanics. I'm already addicted to this channel! Loving it and will watch every video, Thank you Erik for teaching others! I think it's really great how easily you are making it to learn! Something I've always wanted to do. I wish I had the opportunity to have a Lecturer with your talent! Great channel hope you keep up the good work
Heh, I just replaced the rotors on an '06 2WD Ford Ranger today. Same basic setup except the slide pins are not exposed. Glad to see that my procedure did not differ too much from yours.
@fixinggrace Good call on the cheater bar. Funny thing, I had cut the scene where I said not to spin the bearing while cleaning it with compressed air for 2 reasons, first, I thought it sounded kind of "preachy", second I wanted to keep the video as close to 30 min as I could and that saved me 20 seconds. Great comment, thanks for watching.
I have a 79 toyota with the type of bearing. I didn't know how much grease i needed to use. So i fill up the whole cavity with grease. Now i know. Thank you, Eric.
@fliphighup If I'm honest this is one of my favorite videos. Thanks for your comment.
Hello from 2019! Don’t mind me as I pull apart my 63 Galaxie disk conversion to correct some mistakes I now know I made.
Eric, Thanks for THIS! It was an excellent video with super camera positioning for the viewer and extremely informative. I am doing the same on my '79 Trans Am and needed confirmation on a couple things. Sure is appreciated!
This video is the only video I could find that properly showed me how to swap my rotors out on my 1970 El Camino. Great video.
Great video my man. You helped me to save $800 on two occasions now. Thanks for covering all the steps, (unlike the 100 other videos i've watched), in laymen's terms; as i was not so mechanically inclined in the whole fixing cars department. I've even been offering my family, assistance in my newfound expertise, all thanks to you. Best regards.
@shanemaura I'm happy to help, thanks for the comment.
@Buchoass Didn't mean to interrupt your work but thanks for taking the time out to watch. As for pricing it's my policy not to go over pricing sorry, too much liability.
I thought I would just stop back and thank you for posting this video. I used your video to help with my son's 2001 ford ranger (front wheels), and your advice is gold. The audio is great, video is really well lit, and composition is outstanding.
@MrCarlosCruz1 No you can NOT use lithium grease for this, normally you use axle grease. Good luck and thanks for the comment.
You never fail to crack me up, man. Like every 20 seconds or so. You must be from my planet.
you just saved my life tonight! I've never done this kind of one piece and I have a 99 Sierra 2500 hd. beautiful stuff here sir! thanks!
Wow your a real pro. Thanks for sharing your experience. Looks like my mechanic was telling me to use a C clamp. Not knowing it could damaged the master cylinder
When changing break pads.
Never would of thought it could damage the master cylinder. But it males sense And that the seals for break fluid only travels one way Thanks so much enjoyed your video I've subscribed
at the end of this video you mentioned special tools for doing this job for 4x4's. I had a '98 Ford Ranger XLT 4x4 that had to have the bearing replaced. I would have done them myself from the experiace I had from the Vega, but I quickly learned that the hub/rotor assembly was pressed on and would have very special tools to removed/reassemble the hub/rotor. Even to this day I'm not sure what the tools are but I would guess that one of em would be a gear puller.
@michaelovitch Thanks for the encouragement and the great comment.
@ITS4390 I'll keep that in mind. Thanks for the comment.
worked on these before, It was all new to me then. Now that I saw your video, makes me wanna go back and do'em again. Thanx.
@asshatpolice I agree about the cotter pins, I did mention that replacement was the best option but I agree with you 100%. Thanks for the comment and your input. Sorry I got there first, you know you could always make the video and post it as a response to this one, or I could post mine to yours.
Chevy GMC '99 Play in one front wheel. I ordered ACDelco Timken Berings S6 S7 inner bearings and inner seal and outer bearings. Did not use the 2 new races. Compared the brake pads positions on caliper pins on the other side to re-install right. Hand filled the new bearings. New cotter pin. per Ericthecarguy brake pads were near new. Put TireShine w/ polymer (rubber preserver) on the rubber hose (and any rubber bushings and weather stripping)
@ddut887 Thank you for that great comment. Now that I think about it your right, I should have used a clean set of gloves, I'll keep that in mind next time thanks.
@EricTheCarGuy No problem I have to admit the grease packers is actually pretty fascinating to me how that works and gets the grease through the whole bearing assembly.
This video may be ancient but the information is exactly what I needed to put together the bearings on my Studebaker. And it's incredibly well edited for being a 12 year old YT video. Thanks for posting his.
Thanks Eric! Great video, I really appreciate your sense of humor. Your genuine passion for your work shines through in this video. I also appreciated the "improper tool usage" story. I am imagining your instructor scolding you multiple times for shortcutting and using the wrong tool. I look forward to torquing the bearings on my new-to-me 94 dodge wagon.
@wizkid01 Good point. The new rotors had new races installed so it wasn't necessary to install new ones. Use a bras drift and a hammer to get the old ones out and the new ones in if you ever have to do it. I still have the old rotors so I might do a short video on replacing the races. Thanks for the comment.
@chechnya That is EXACTLY why I do this. Thanks for the comment.
Excellent video. Another way to manually pack grease into the tapered bearing is to put blob of grease into palm of hand and slap wide side of bearing into blob until grease gets pushed out the narrow end of the cage, rotate and repeat until bearing is fully loaded. Disposable gloves are good.
@sheupel No, that seal replacement is a bit more involved. On a GM you would need to remove the cover on the diff to remove the 'c' clips that hold the axles in. The closest thing that I have for that is the video I did on changing the bearings on a Jeep, I think that video is listed under "Removing Pressed On Bearings".
Your are awersome! Been watching your channel for a long time. Your are helping me keep my 1996 chevy blazer going which now has over 341,000 miles on it! Thanks so much
I'm going to be doing this on a friend's Ford Ranger. I forgot to print the tightening procedure for the spindle nut at work so I'm just going to tighten it like you did. The torque specification was only a couple of inch pounds. I've never done these kind of brakes before. I've only done the kind where the rotor is sandwiched between the wheel and the hub assembly.
Very thorough as always Eric. A couple of things I've found is that a cheater bar works on the allen wrench if you're too chicken to use the hammer (like me). Another is using compressed air to clean or dry a roller bearing. It's important to not let the bearing spin when using the compressed air I've seen these things fly apart before. 20 rollers flying every which way can cause a lot of damage or injury.
Had a hard time remembering back to the last time I did a brake job like this and didn’t want to damage the inner race. I’ve been doing this independently for about 4 years now so I don’t often get shown tricks of the trade anymore, I’m left to come up with it on my own now. This technique for removing that inner bearing and seal is absolutely fucking brilliant. Makes me wish working in a shop with all the old geezers. Don’t miss the hours and pay though 😂 Thanks for doing what you do Eric! Keep on keeping on wrenching
@EricTheCarGuy Thanks a ton, EricTheCarGuy. I am not that mechanically inclined or equipped to somehow secure the race, so I'll probably end up replacing the rotor. Probably best I do it now, and avoid any more costly repairs down the road. I am simply worried about it either scoring the spindle, or running too hot and seizing. Thanks for the quick response and I enjoy all your vids, even those not related to my car's set-up. They're very informative as well as entertaining.
@13FravelJ The only time a rotor needs to be addressed is if there is a brake pulsation or damage to the rotor itself, many manufacturers recommend just replacing pads when brakes are needed if the criteria mentioned above are met.
2k18 this is why i subscribed 5 years ago....keep it up eric and stay dirty
@wardubo I try to be thorough if nothing else, I figure if I've never done this I want to see every step so that I can do it myself, I wish I had these videos when I started out, would have saved a lot of mistakes. Thanks for your comment.
Thanks! Only video i found explaining the whole process. Everybody else Starts with the bearing in their hand. As someone with only sealed bearing experience.....I found these videos...alarming
Hi Eric, I have a 96 dodge ram 3500 1 ton..my bearing welded itself to the spindle I literally split the hub to get it off..I finally got everything back together and tomorrow I will do it right haha..didn't know the castle nut should not be tight..thanks for video!
@DieselCrawler86 Yep, I try to learn every chance I get. Glad you caught that because it was for you.
Awesome video! Still helping people 11 years later!!
@MrYahya1421 Now that I've been partnered I don't have to split them up into 10min segments anymore. It's nice because I've noticed that the first video gets more views than the rest. Thanks for your comment.
I used this to do wheel bearings for the first time on a friend's truck. Saved my ass and some money! Great demo!
Would you believe it took me 15 videos to find yours that shows the correct orientation of the inner seal?! Thank you!
Went through about 5 videos just to find your cool trick to removing the inner tapered roller bearing. Thanks!!
@southernpride903 The lubrication of the slide pins and the brake pads helps a great deal to keep things quiet, the rest is up to the part. Perhaps you should recheck your work to make sure everything is correct just to be sure.
I remember doing this job on my 1981 Grand Prix. I wish I had this video back then, Great job Eric!
@shieldcracker Thanks for watching and subscribing I really appreciate it. I'm glad you like the video and that it was able to help, thanks for letting me know with this great comment.
Wow .....
10 years and you still been the same ... congratulations..!!!! Love your videos .!!
@shrimp909 Thanks for the comment and letting me know.
I sprained the knuckle in my thumb while pushing an allen wrench.. Now I keep a foot of 1/2in black pipe, works great on any size allen!
@axenz1 It does appear that way, your comment makes me smile, thanks.
@lasersdend15 Glad I could be a part of your education. Thanks for taking the time to let me know, it means a lot. Stay dirty.
you dont need really to borrow a bearing packer if you dont have. just get a zip bag and fill it with axle grease and then put the bearing in it and massage it. instant bearing packer :)
A fun old video.
I have a Fiero that stock has the same type of rotor integrated with the hub. But the rotors are a solid 9" rotor. So I took a stock hub/rotor, cut the rotor off, pressed longer studs in, then used a Chrysler Lebanon GTC rotor(11 1/4"). For the caliper I used a d154 caliper, the same caliper from this video.
ChrisFix and Eric are the best mechanics to watch on youtube. Period.
Also sma
good stuff...i did pick up a few tips......If you are going through this much trouble, i would put new bearings in...they are cheap...like $10. when tightening the castle nut, i tighten them until i can barely move the washer behind the nut back & forth w/ a screw driver.
Im a rooky lol, thats how some call me at the dealership shop, I replaced front pads on a 2015 Traverse, and you know, I had to push back the pistons... of course the brake fluid started dripping but the worst was the car never came to a stop unless I push the soft brake pedal all the way down!!! My trainer said it needs a new master cylinder. I really love those pliers, Im gonna make one for my self. Thx bud
@RAJSTA81 I did just shoot a video of a timing belt replacement on a 99 Integra with a 1.8 DOHC but that won't work for you. I've gotten in the habit of recording every timing belt I do and should I come across the one you asked for I will let you know. Thanks for the comment, sorry I couldn't help more.
yo Eric i just finished installing my new wheel bearing thanks to you ....i was installing new ball joints and when it was finally time to tighten the last nut which was the spindle nut i tightened it real good and when i got home from work i noticed my dust cap came off the washer with tooth in it was bent n the bearing was destroyed behind it....ooops!.....haha then i found your video which helped me put my new one on.....i got an 01 sonoma just like the one in this vid!.....you rule dude stay funny your vids r great and have a good one!
I understand if your doing it for a customer not to replace them if they do not want them replaced but I would highly recommend it to them. It only makes sense for no more than it costs.
@spelunkerd These are by far my favorite comments, thank you.
(old school referring to that modern hub/bearing assemblies are now usually a integral unit, complete with lug studs- that is Torx bolted to the knuckle, and the rotor is just an empty rotor that slides on- like most FWD vehicles.)
@southernpride903 I agree that you first need to find out what's loose. Watch the video I did on Axle Ball Joint Replacement, at the end I show how to check for play in the front suspension, this works for just about every make. Good luck.
Wow! An old school video from EricTheCarGuy at his old shop I actually never seen before. .
I put new brake pad on 2007 ford range it white smoke why
+alberto Galvan Did you spray anything on the rotors when you replaced the pads? Are they new rotors?
that was sweet i leaned a lot thanks eric. also that seems like a better and simpler design then what they have now
@jgizzy Sorry to take up your time, you know I have no intention of taking the videos down anytime soon so you can always subscribe and come back when you have more time. I'm still giving you COTD for this. Thanks for the great comment.
wow thanks for the vid. HAve to do these on a ranger and had no idea how to proceed, never seen that setup before.
@Chris07860 This one is actually one of my favorites, thanks for your comment.
You were so Happy to do this kind of work in 2010, times have changed.
@RAJSTA81 I will and thanks for the great comment.
Hey Eric, thanks for the video, a couple little tricks that you showed saved the day.