Starlink Gen 3 Standard Wall Mount - Review and Install Tutorial
Vložit
- čas přidán 4. 07. 2024
- In this video, I go over the Starlink Gen 3 Standard Wall Mount accessory. This official Starlink mount allows you to permanently mount the Gen 3 Standard dish to an exterior wall, eave, or fascia. Learn about the features, learn what comes in the box, and watch me explain step-by-step how to install the Standard Wall Mount.
Blog post: www.starlinkhardware.com/gen-...
Starlink Cable Routing Kit Review and Tutorial: www.starlinkhardware.com/star... - Věda a technologie
Looks simple and straightforward. Thanks for a detailed video. I'm looking forward to receiving my Starlink.
Nice video. I would only add that the loop you made at the bottom of the exterior cable rub is very important. The cable should always enter the structure from a lower elevation. Otherwise water will run down the cable and into the structure. If you are running the cable through the soffit or a gable vent and don't have that service dip, you will end up with water in the attic.
Good to know, thanks for the additional info!
Thank you for your video. I feel more confident in my purchase
Hello, I work for a construction company in Japan with an installation record of over 120 Starlink units (about one every three days). Since the antenna kits and mounts discussed in this video are not yet available in Japan, this has been very informative for us. However, I would like to point out that using lag bolts (coach bolts) for mounting on the roof fascia alone may not be safe due to insufficient material thickness. It is recommended to secure them in areas with more substantial backing where the bolts can anchor deeply.
Also, I strongly recommend wearing a helmet when working on ladders for safety.
Regarding the original mounts, while they may seem less reliable, I am curious how well they would hold up against the typhoons that are common in Japan during the fall, which bring winds of up to 80 km/h (22.2 m/s). From my perspective, it is questionable whether they would withstand such conditions.
Thank you for your detailed instructions. Much appreciated!
You're welcome!
What a fantastic video. Well done. Thank you
Well done & very helpful video, thanks for taking time to do it!
Glad it was helpful! Thank you for watching.
Perfect installation video !
Haven't decided on Star link yet, but appreciate this video in case. Still up in the air on Star link. I have slow DSL, less than 25mbps.
I also had DSL and switched. Getting average 250 mbps and 30ish up. Lovin the switch.
Great Install Video!
If your company does custom mounting Solutions, you should do a v-mount backing plate, so it is perfectly centered at the roof line. It's slightly off to the right. Not a big deal but if you want it perfect I would do the back plate.
Always your videos Youse full
Thanks
I’d like to mount like this, but somewhat concerned the fascia isn’t thick enough to support? Maybe a short piece of 2x4 screwed into the back to help deep sink the lag bolts?
Excellent video. Answered a lot of my questions and concerns. I agree that the Wall Mount looks cheap and will probably fail. Appears that the dish still needs to be oriented to the north. We have a gen1 and 50 foot trees to our North so it has never been useful, too much obstruction from the trees.
Thank you, great video!!!
You are welcome!
Do you think the next generation of flat high performance is close?
What is the wind rating of that mounting? That bracket looks cast. Without washers I would expect it will crack at the bolts. The seating does not look deep enough and wind will pull that out of the bracket.
its thick, the whole unit is well made, its all splined, real tight tolerance i just got mines and i'm impressed
I have found it almost impossible to find the Gen. 3 adapter. I have the mount, just not the mast or adapter that clicks into the back of the antenna. Do you know where they are available? I want to mount it this weekend, if I can get all the parts together. Thanks in advance.
It sounds like you bought one of the Gen 2 wall mounts, which aren't compatible with the Gen 3 dish. You need the "Standard Wall Mount" in this video, which is a Gen 3 accessory. When you visit the Starlink shop, you need to select the Gen 3 dish to view compatible accessories. The Gen 3 Standard Wall Mount comes with the adapter and mast, as shown in the video.
Given it is a slide and click adapter, wont strong winds break the clip of the adapter and have your dish fly away?
Unlikely. There are two locking tabs, and it takes direct upward force on the tab to disengage them.
I have the Gen2 wall mount here in NE Idaho...Its put up with 60mph winds, rain and snow...Never budged... When will we be able to order the Gen3 package???
It’s been out for a couple months for customers in the US.
Can this install just the mast & panel adapter on top of Starlink yard pole anchored to Airstream trailers the V3 ROAM Starlink?
I'm not familiar with what kind of mount Airstream is using, but you could adapt just the mast to a similar size mount, assuming you have some kind of bolt or clamp to secure it. I wouldn't think it would be a direct fit, though, unless designed for Gen 3.
I'm on day 3, trying to get answers to mounting by gen 3. Customer support sent me a video of a pivot mount kit, that includes a base and mast for gen 3. The pivot mount I purchased did not include the base or mast that attaches to the gen 3 dish. Starlink's SHOP site does not show one. Do they expect us to setup our Starlink Kit, setting in the yard, to get the support we need. This is the worst support I have ever dealt with! You send them a request, wait a day for an email response that doesn't address the problem. Then, send them another email and wait, how long for a response. With the cost of equipment, the $120 a month for service; this is the support you get!
Do all the mount kits come with the adapter that replaces the kick stand on gen 3 (the long and short mount, the pipe adapter, and the pivot mount do they all come with the “mast the adapter” plastic clip that replaces the kick stand
Only the mounts designed for Gen 3: Standard Wall Mount, Standard Pipe Adapter, Standard Pivot Mount. Long/Short Wall Mounts and other Gen 2 mounts aren't compatible with Gen 3.
The only mount that came with my Gen 3 was the kickstand. I was very disappointed to find this out when I got here. Unfortunately, I can't blame anyone but my husband, because he did the ordering. I'm not completely sure if my husband knew if we were going to need a mounting kit. We still haven't received our standard pipe adapter yet. It's been almost 4 weeks.
@@billiejostoddard372I think the gen 3 pipe adapter was recalled. When you receive it, make sure it’s the new gen 3 version.
What is the OD of the pipe. I'm thinking of using this along with the Harbor freight flagpole.
Funny how everyone neglects to mention that wee little detail.
are you able to unplug the cable from the dish?I ordered the mount but already set up the dish
Yes you can. I just set up my standard mount and had my Gen 3 dish in my yard until the mount arrived!
nice video.
Great video, thank you! I just ordered mine for my cabin. Should i expect the Gen3? I ask because i recently rec'd my Business/High performance starlink for business and i rec'd the Gen2 rather than Gen3. BTW, the High Performance is not near as easy to mount and assemble. Also if you rec'v the Gen2 high performance and wish to connect to a network you need an ethernet adapter. Gen3 high performance router includes onboard ethernet port. Just FYI to anyone who considering the high performance hardware.
If you are in the US, you will get a Gen 3. It's the only version available from Starlink in that market. Australia is the other market offering Gen 3, but customers have a choice for now.
Thanks bro!!
What phone are u using with app?
Can i use the kick stand to first determine best location skyward to point the dish ?
Yes, that’s a good idea. On the ground, set it up and open the alignment tool. It will be the same direction on the ground as on the roof.
does the kit have a part number so I can look it up?
I don't think there is a part#, but here is the direct URL to the shop page: shop.starlink.com/products/us-consumer-wall-mount-gen3
Hello, I saw your video and I would also like to order Starlink, but there is one problem. With the initial order it seems to me that Starlink wants to give me the second gen instead of the third one, as I prefer the third gen a lot more due to the conditions where I live. Will Starlink give me the second gen anyway or will it give me a third one instead? As though it looks like the second gen according to the pictures and description.
in my area they let you choose during the ordering process
not in mine, I come from Slovakia
@@frantiseklos7283 I've read in other comments that the Gen 3 is US only, but that will probably change in the future.
can be, starlink I ordered came to me 2 generation, from the speed I'm totally satisfied I'm downloading some stuff my brother plays online games and others are also on the Internet and everything goes without problems. The only downside is that it doesn't have a LAN port. It's the 21st century and the router doesn't have a LAN port
@@frantiseklos7283 That's unfortunate with the Gen2. But you can buy an adapter to convert to LAN. It's not needed, as I stream 4K video via WiFi on my smart TV.
Any foreseeable issues with wind or snow?
It's survived the winter here so far! The mount itself is secure with the 2 lag screws. I found it nearly impossible to separate the mast from the mount adapter. Despite being plastic, I also trust the mounting adapter plate that snaps into the dish. The wobble isn't confidence inspiring, but from what I can tell so far, doesn't appear to have any affect on performance or stability of the mount.
Is there something I could build to shelter the satellite dish that would not interfere with the signal?
Starlink recommends that you don't cover it with anything, but Starlink dishes have been able to function under fiberglass, glass, fabric, etc. Your results will vary based on what type of material you are using. It doesn't really need to be sheltered from anything, though. It's designed for outdoor use.
@@StarlinkHardware We are a rainforest and have hurricanes. I love your product. But because of the shape it's a windsail/wing/kite. We have Willy wahs, wind comes from all directions and blows hard. We don't get much attention because we are rural. I believe an enclosed box structurally reinforced would help us. we had 150 inches of rain this year.
I’m trying to figure out the best type of mount but it seems they all would not do very well in strong winds. We are in hurricane territory and this doesn’t seem sturdy. I was wanting the pole adapter kit but it also seems like it wouldn’t stand up to much.
Does this turn 360 degrees?
Damn strong wind like 60 mph blow it off the mount hanging by the cable
This has been through 50-60 mph gusts during storms and it didn’t budge.
where can i purchase this mount or the roof mount?
shop.starlink.com
HOW DO I ORDER THE WALL MOUNT KIT I ALREADY HAVE THE STARLINK GEN 3?
Here is the link to the Starlink shop where you can purchase it: shop.starlink.com/products/us-consumer-wall-mount-gen3
Im new to starlink and my satellite arrives tomorrow but im worried that I may have ordered the wrong wall mount. I ordered the short wall mount but nowhere on the box or instructions does it say that its for the Gen 2 or Gen 3 satellite. Any clarification would be appreciated!
The Short Wall Mount is for Gen 2 only. The wall mount that is compatible with Gen 3 is called the "Standard Wall Mount". Starlink's online shop doesn't do a good job of telling you compatibility. What you need to do is visit this URL, and pick the Gen 3 dish to view compatible mounts:
shop.starlink.com/pick
@StarlinkHardware That sucks 😅 but thank you for clearing it up so hopefully nobody makes the same mistake I did.
Whats the wind rating with this mount?
Starlink hasn't assigned a wind rating, but based on my experience and time with it, it's able to handle moderate winds like 40-50 mph. I've had gusts up to about 60 mph in storms with no issues.
@@StarlinkHardware Try gusts of 120 MPH.
Your name is Colby?
Where can I get this kit
Available, location Onitsha
Is price is only 55 for starlink system??
This mounting accessory is separate from the Starlink system. You can check prices for your market at Starlink.com. In the US where I am, the system costs $599.
@@StarlinkHardware i wait to be allowe in iraq
We experience hurricanes. Need a hurricane mount
you should probably take it down for a hurricane. try living with tornadoes where you don't get months of notice.
I think this one
OK.
I live in south Texas (4 miles north of Mexico). We regularly get high winds. That flimsy joint between the mount and mask looks like the Gen 3 Antenna-Dish would turn into a good kite.
I purchased a gen 3 kit, but unable to mount it to my roof. I bought a pivot roof mount and 150' cable in advance to mount. It was for a gen2 but didn't know it wouldn't work until my gen 3 kit arrived today. Your video says you have to have a gen 3 kit to be able to order gen 3 adapters or parts. I go to the shop menu and it doesn't list any gen 3 mounts. You send a kit and expect people to just set in your yard. Seriously, the prices we pay and have to continually purchase more! Tell me what kind of customer will leave a dish in their yard for someone to walk away with? Your customers deserve better and don't get me started on your customer support, that doesn't seem to exist
You can select your dish version to see the appropriate accessories by click the “Not your Starlink” link in the shop, or visiting shop.starlink.com/pick. Compatibility is also listed in each product description.
My channel isn’t affiliated with Starlink, so I can’t address the other issues you raised.
Plastic snaps on the dish make me nervous. One instance of bad weather and you're down $600.
Vertical surfaces are Plum my friend. Level is for horizontal surfaces
Plum is a fruit, I think you meant plumb. Just giving you a hard time, thank you for the correction!
Grammatical errors and punctuation mistakes brought to you by Google Voice to text.
@@StarlinkHardware your video was very helpful. We are about to pull the trigger on gen 3 in the next few days. Thank you
The quality of hardware being supplied with the generation 3 setup looks much more inferior and lesser quality compared to the earlier versions,I had been seriously considering Starlink as an option for my internet setup but after seeing a number of videos of the new gen3 hardware I have to say I'm unimpressed........
Gen 3 is trash. Standard Actuated was the best way to go.
Buy gen 2. It's pretty cheap now...
@@skullystrench6048probably they changed from gen2 because of the cost, not quality of connection and speed...
😂😂😂 All the structural parts are made of steel, what do you want, heavy gauge titanium?
My gen 2…. Slapped it up there anywhich way and it did ALL the alignment by itself.
Starlink Fascia mount 😅
The Gen 3 feels like a cheap and nasty downgrade.
It is certainly cheaper to produce for Starlink. In my opinion, quality has gone down hill with every dish since the V1/V2 round dishes.
Who cares as long as it works?
That new flimsy mounting system is awful. Those two little clips will give way under a big gust. Don’t get me started on the pole mount that has already been recalled by SpaceX. People don’t really like their expensive new dish flying off their roof. SpaceX obviously never tested the new dish in real world conditions
I doubt it based on my experience so far. You have to lift up and slide the mount plate out at the same time, not something wind can do. Obviously, don’t keep your dish up in a tornado. But in Starlink’s history I’ve seen very few properly installed dishes fail because of wind.
@@StarlinkHardware there is currently a recall on all pole mounts. A lot of people had their antennas destroyed because of the poor design. That is not just my opinion. The two tiny clips that will likely fail in strong winds is, along with many other reviewers. The V2 was objectively a much stronger design
@@gammagonad1657 The Pipe Adapter recall had to do with the bolt, it could loosen over time. It had nothing to do with the mounting plate or how it attached to the dish. Anyone concerned about Gen 3 can always just buy Gen 2, as both are available. But I have all the mounts and multiple Gen 3 units being tested, and they are holding up fine.
@@StarlinkHardware I never said the recal had anything to do the mounting plate, but once that’s fixed just you wait and see it will definitely be a problem. It obviously was not as well designed from the beginning like the V2 was. You can tell that not much thought was put into it other than “build it cheaper”
I cannot for the life of me understand why the cable is not installed in conduit. Cables should never be exposed outside a premises or below a certain height inside the premises. I thought this was a Starlink authorised video. This guy is just an amateur.
Conduit is overkill, the Starlink cable is rated for outdoor use. The official Starlink instructions don’t call for conduit. I’ve had my original dish installed for over 3 years, the cable is fine.
@@StarlinkHardwaredon't pay attention to attention seekers.
These are low voltage and weatherproof cables, no need for conduit.
Do you see phone, coax or fiber in conduit?
Do you expect your customers to start drilling into their homes and leave the dish setting in their yards? Then drill more holes, if or when they get the proper parts to mount it to our homes or yards. Or, activate their kits and wait for the proper mount that will hold up in real world conditions. We customers deserve way better, for the prices we pay. Come on, plastic clips!!!!
The whole dish is made of plastic, I don’t think it’s an issue. Mine has been installed for awhile through 40-60 mph gusts with no issues.
I hope you know this CZcamsr is not starlink themselves he is just here to help support those who are interested. So he doesn’t have “customers” 💀😂
Dude think this channel is Starlink’s 😂
@@StarlinkHardware 40-60 mph is a mild breeze !
You kind of over explain things. I don't think children are doing the install.
If this video was clear enough that children can follow, that’s about the best compliment you could give me! Thanks for watching.