F3E2 error code maytag washer

Found 2 cracked wires at the temperature sensor at the back of the unit once wire was almost broken, that's why everytime it was agitating it was creating error code, resoldered it back, works perfectly fine 😀

[@chrisgailus3411]

Hameed, this video saved me hundreds of dollars. I discovered the exact same issue with a cracked wire at the zip tie that you identified in the video. I never would have noticed it without this! Thank you very much for helping me! I soldered the wires, shrink wrapped the connection and I’m back in business. Incidentally, over the past 10 years I’ve also repaired the washer filler hose, the front door gasket and the door locking mechanism all with help from CZcams so thank you for helping us home handymen! 👍🏼👊🏼

[@hameedwafaAFG]

Thank you for your feedback!

[@dcppcp]

Thank you so much for posting this, Hameed. I actually went to a repair shop first asking about the code and they mentioned it was the temperature sensor failure code. I found your video and I had the exact same issue with a broken wire on one of the two conductors exactly at the nylon zip tie. Apparently it is a relatively common failure point because the factory didn't allow for enough slack to account for tub vibration. I crimped on an electrical crimp sleeve and did NOT replace the zip tie and I am back up and running.

[@hameedwafaAFG]

Dale Coffing good for you 😄 👌

[@biglefttoe76]

Thanks for this video Hameed. Had the same problem and you helped us avoid a call to a repair shop. Same broken wires right at the tie.

[@hameedwafaAFG]

Nigel Reedman you are very welcome!

[@blueridgerobbie]

Thank you. My wires were also broken. 15 minute fix.

[@pioadventures]

This helped me although thr wire wasn't broken. I just took the sensor out and put it back in then somehow it worked.

[@jakeweirich]

Thank you Hameed. We had broken wires also and you saved us $300!

[@kirkarnold9023]

Thanks... I looked at the wire and it looked ok. but when I saw you find the broken wires. I said to myself Maybe it is the wire. So I cut the tie off and the black wire was broken.
You saved me some money too... I will subscribe.....

[@hameedwafaAFG]

Kirk Arnold good for you!

[@kimmymounkes6087]

I have MVWB765FW model Maytag commercial technology topload and is showing f3/E2 error codes. I have unplugged it to reset but it isn't resetting can you possibly show me a video they are only showing bravos xl

[@mdbrenna]

Hameed FTW!! Thank you sir!! Saved me a service call!!

[@vanboy20078]

Hi Hameed, I have the same issue, wires are fine, I replaced the sensor too same problem. The washer door is locked as well, any ideas? Any help would be much appreciated. God bless.

[@hameedwafaAFG]

Hello , for this problem I would follow the tech sheet , unfortunately I do not have full access until Monday

[@fabc6090]

Thanks Hameed your a life saver

[@airies21]

Thanks very much sir!same here broken wires too!

[@benteeter1076]

Thank you sooo much for posting this video!

[@nomadicMondo]

So we have the same code. I replaced the sensor, and wires seem to be fine as well. It only happens when the spin cycle is going, so no water should be coming in. Could it be a false error? I’ve cleaned out the filter, and water does indeed get pumped out at different times.

[@hameedwafaAFG]

nodeGarden Mondo did you check your coin trap, the black rubbery piece under the washer tub?

[@nomadicMondo]

That was the one place I didn't check. Turns out to be the sensor wire, though we can't find WHERE the fault is. A bit of wiggling, and now it's worked for 2 days. If it happens again, then we'll just replace those completely. Thanks

[@hameedwafaAFG]

nodeGarden Mondo keep eye on it and see what happens ✌️

[@nitroprime9714]

tyvm was my exact model and problem.

[@zaza-pc9kd]

perfect maaaaaan ,salamalaikum