How To Install High Side Peak Trim. Peak Flashing Installation For Corrugated Metal Roofing Panels
Vložit
- čas přidán 16. 07. 2024
- Learn How To Install High Side Peak Trim. Step By Step Corrugated Metal Roofing Installation Video. Installation Instructions For Peak Flashing On A Metal Roof With Exposed Fastener Metal Roofing Panels.
Install metal roofing like a pro. Metal roofing trim installation video that covers finishing and cutting the ends of the peak trim at the gable corner, overlapping peak trim, foam closure installation, and fastening. This video covers the following exposed fastener panels: Corrugated metal roofing, R Panel, PBR Panel, U Panel, 7.2 Panel, Western Rib, and Ag Panel.
In this video you will learn about:
00:00 How to install peak trim on a metal roof
01:09 What are the required tools and supplies for peak trim installation
01:39 How to install high side peak trim
01:49 How to cut and finish the ends of peak trim at the gable corner
03:11 How to install foam closure for a peak trim on a metal roof
04:00 How to overlap peak trim
04:42 How to fasten peak trim on a metal roof
If you already have not purchased your metal siding panels give us a chance to bid your job. Save 15% to 50% with our manufacturer direct pricing and great customer service. Inexpensive delivery anywhere within the United States.
Visit Our WEBSITE
bit.ly/wsmr-website
Visit our LEARNING CENTER
bit.ly/learning-center-wsmr
This is not intended for standing seam panels.
Install Corrugated Metal Roofing
Download Our INSTALL GUIDE
www.westernstatesmetalroofing...
How To Install Peak Trim Flashing On Metal Roof. A Step By Step Guide
You already know the benefits of installing a metal roof on your home. But if you’re a DIY homeowner or installer, thinking about the actual installation of the peak trim can be intimidating. Where do you begin? How can you make sure that your roof is installed properly?
At Western States Metal Roofing, our goal is to make your installation as simple as possible. We always recommend to refer to the manufacturer’s metal roofing installation guide as your primary reference, but we take it a step further.
In this foam closures installation video we will cover:
What Is Peak Trim?
Tools and supplies
Peak trim at gable corners
Foam closure installation
How to overlap peak trim
How to fasten peak trim
What Is Peak Trim?
Peak trim is a metal cap for a single slope roof condition that caps off the high end of the slope. Peak flashing acts like a ridge cap to keep water, snow, and ice from getting under the roof. It’s also referred to as peak flashing or high side peak trim.
The most common roof condition is an “A” frame roof that has two sides and requires a ridge cap flashing at the peak of the roof. A single slope roof is half of the A-frame as shown in the example below. Single slope roofs require a peak or high side eave flashing at the high end to cover and protect the metal roofing.
How To Install Peak Trim On A Metal Roof
Step One: Cutting And Finishing Peak Trim At Gable Corners
Step Two: Foam Closure Installation For Peak Trim
Step Three: Overlapping Peak Trim
Step Four: Fastening
FOLLOW US ON SOCIAL MEDIA:
FACEBOOK: bit.ly/facebook-wsmr
INSTAGRAM: bit.ly/instagram-wsmr
TWITTER: bit.ly/twitter-wsmr
LINKEDIN: bit.ly/linkinin-wsmr
HOUZZ: bit.ly/houzz-wsmr
PINTEREST: bit.ly/pinterest-wsmr
CZcams: bit.ly/youtube-wsmr
You guys are life savers. This is at least the second video from Western States Metal Roofing that has been a lifeline for this clueless DIY metal roofer. The manual and online material from the company I purchased my materials from is very basic and completely omits the finer points that you carefully explain and demonstrate. Many thanks.
C Norma, I appreciate the kind words and glad we could help. Good luck on your installation.
If you need any additional videos, you can find them all in one place on the website
www.westernstatesmetalroofing.com/corrugated-metal-roofing-installation-videos
Great job easy to learn as I. Looking forward to build one.Thankyu for this vein.
I have a lean to house metal carport. I wanted to create a peak roof to make it look more symmetrical to my house. How do I do that?
Do you have hip cap where it connects at the top of the roof?
the videos very helpful but in this videos i found a mistake that the head berge always be above fold of side berge.because side berge is down than head berge.
Hi,like the video's very much...
I am doing a 16x30 lean to off of an existing pole barn with a 4/12 pitch. I am removing the existing facia board and tiying in to the trusses approximately 2 feet back. The pitch on the lean to is 3/12...how do I do the over lap of the old and new section of the metal roof ?
Thanks so much.
Are you referring to a transition flashing (pitch break) ? If so we have a corrugated metal roofing installation playlist on the channel. There’s a video for high to low and low to high transition installation. Hopefully that will answer your question. Have a great Xmas
Great video. Very helpful. BTW, what cutters are you using? The bolts on mine get in the way about 2" into my cuts. Yours look much more effective
Thank you for the positive feedback.
Midwest snips. Model 6610R & 6610L.. Can be found on Amazon
@@WesternStatesMetalRoofing Great, thanks
@@WowRixter Ric, just for our internal purposes trying to figure out who's viewing these video's.
Are you a DIY installer or a contractor?
Thanks a million, Paul Rubio
@@WesternStatesMetalRoofing A DIY'r in Canada. I bought a metal roof for my son's lean-to shed and was Googling how to install the gable and peak trims. I don't, unfortunately, own your product, but did find the video to be excellent. Very clear and concise
@@WowRixter I appreciate the feedback. Good luck on the install.
Hi thanx, quick Q what Sealant do you use.
Novaflex silicone sealant
I need to find peak trim, but every hardware store and big box store doesnt have it. They label a gable trim the same, but it isnt the kind meant for single slope roof.
Is the High Side Peak trim component the same as the Gable trim or is it a unique profile? If so, what makes the profile different from gable trim?
No. Gable trim is installed on the two sides of a building that do not have a pitch. Ridge cap or peak flashing is installed on the part of a roof that has a pitch. Gable is a 90 degree bend, ridge or peak flashing is bent to follow the pitch of the roof. Buy your peak trim from whomever sold you the metal panels. If they can sell you metal panels, then they can source peak trim for you.
I'm having trouble finding peak trim for the roof I'm building. Where is a good place to find it? I am using it for the three rib panel roofing.
Your local sheet metal shop should be able to help you out. Better yet, if you're buying metal roofing panels, they can be purchased at the same time.
How close to the top edge of your roof should the metal panels be? I'm currently building a lean to shed with a 15 foot long roof. I'm trying to figure out if two pieces of 8 foot metal sheets will be long enough given the overlap length wise.
Matt,
Here is a written detail for this condition
www.westernstatesmetalroofing.com/peak-high-eave-flashing-ws-19-corrugated-trim-flashings.html
The metal panel will go to the edge of the wood substrate as shown in the detail. You will want a minimum 6" overlap on the corrugated panels themselves.
Given you have 15' and two sheets at 8' you will be fine.
What double sided butyl tape is that? All I can find are flat tapes that don't have the "bead" on either side...
It's just a typical double sided butyl tape, Tape, 3/32"X3/8"X45' Roll
www.westernstatesmetalroofing.com/butyl-sealant-tape-for-metal-roofing
Video