FMF Gnarly | Installing a new Pipe on my Husqvarna TE300i

Installing a new FMF Gnarly pipe to my Husqvarna TE300i to replace the OEM pipe / expansion chamber that has a dent in it.
The FMF Gnarly adds more torque to the bottom end; is made from 18 Gauge steel with a nickel plated finish, making it stronger than the OEM version and an ideal upgrade for any Enduro dirt bike.
Spring puller and pick set - amzn.to/3FugU51
High Temp Grease - amzn.to/3Bz7N0z
DeWalt Tool Kit - amzn.to/3F5lSU5
Large rubber gloves - amzn.to/3P6uqPs
Medium rubber gloves - amzn.to/3UzILoC
Small rubber gloves - amzn.to/3P3X1oz
My Motovlog and on-the-go charging setup:
Helmet Gripper mount: amzn.to/3NdQ03F
Purple Panda Microphone: amzn.to/42EbSeo
GoPro Battery Charger Power Bank charges my Phone and GoPro batteries while when I'm riding the: amzn.to/440MeBE
Official GoPro Enduro Battery: amzn.to/43UBLYu
DISCLAIMER: Links included in this description may be affiliate links. There is no additional charge to you If you purchase a product or service with the links that I provide but each purchase helps support my channel so I can continue to provide you with content!
#enduro #dirtbike #FMFGnarly

[@mikeyx2415]

Did you notice any significant loss of top end power when using this? Thinking of grabbing one for a little more oomph on the bottom to mid but don’t want to absolutely gut out top end for it, losing some overrev and such is fine by me though

[@MALVSMACHINE]

To be honest Mikey, I don’t remember much difference, but you’re probably a much better rider than me so will probably notice more in a change of power than I would 😄

[@gvnthomas]

Shiny!

[@MALVSMACHINE]

Certainly is! I hope it stays that way too….. it’s supposed to give a bit more bottom end grunt but I doubt I’ll notice it 😆

[@gvnthomas]

@@MALVSMACHINE Even if you don't notice it you can still say it's there plus Shiny!

[@MALVSMACHINE]

@@gvnthomas absolutely 😆

[@jarredtremain4644]

Got same pipe ready to fit my 18 te300. Was told take muffler off to install expansion chamber properly in line and seated. May have to trim a little bit off joining end of chamber so that everything lined up and not forcing pipe out of line with head. Bit of grease or silicone on orings makes it easier to install and seals better. Avagud1

[@MALVSMACHINE]

Cool stuff, they look great! I ended up loosening the muffler to fit mine and it went in no issue, I just had a nightmare getting the second bolt to meet the thread. I got told off by a family member for not putting grease on the O rings so will remember that from now on😆. Hope you enjoy your new pipe mate 🤘🏻

[@jarredtremain4644]

When trying to fit springs in to motor before pipe, pull hook out hard on one side and wedge abit sideways, this will help hook stay extended and in position, then softly with hand and don't touch anything until in position on head. If do hit hook it will fall into spring easy. Avagud1

[@MALVSMACHINE]

Thanks very much Jarred, I went in blind with this one and the springs caught me out 😆.

[@TruenorthmtGod]

I have a 2024 will it work?

[@MALVSMACHINE]

I haven’t even seen a 2024 model yet dude so don’t know the answer. Would be worth checking the FMF website to see if they make them for your particular bike before buying 👍🏻