How To Power A Runcam Thumb With Balance Leads (Thumb Pro Too!)
Vložit
- čas přidán 1. 01. 2023
- In this video I show how to power a Runcam Thumb or Thumb Pro with power leads from a 2-6s lipo.
Wolfwhoop PW-D Control Buck Converter 6-24V to 5V 1.5A Step-Down Regulator Module Power Inverter Volt Stabilizer a.co/d/6wvhQi4
SoloGood 10 PCS JST-XH 2S/3S/4S/5S/6S Battery Balance Plug Silicone Wire Extension Lead Balance Leads Extension Cable for LiPo Batteries Balance Charging(Each Size 2pcs) a.co/d/7MERhcI
iFlight 2pcs Upgraded 90° Type C to 5V Balance Plug Charging Cable for GoPro Hero 6/7/8/9/10 Used for 3-5inch FPV Drone a.co/d/9WbI8vT
560PCS Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit with Box(5 colors/12 Sizes) a.co/d/8Q406e6
#runcam #thumb #thumbpro #fpv #soldering #howto #diy - Věda a technologie
Very cool!!! Thank you for sharing!!!
You're welcome
Hope it helped😁
Thank you very much. I thought only 4s to 6s is possible using JST-XH cable. Great relief now. Thanks for shedding some knowledge. Helpful video 😊
I'm glad I could help🤟
it sure did!!! Thank you so much again :)
Awesome 🤟
Thank you, made several different ones!
You're welcome, I'm glad it was useful 🤟
I almost made a video like this last winter. I do this for my naked GoPro.
I wish you made that video last winter, Its something I could of used last spring 🤣 hopefully this helps out some people
@@lillygodzilly yeah I saw Albert Kim I think do it.
Great video. Thinking about using one of these setups on my rc trucks for a FPV while bashing. Hopefully it’s not nauseating as by scale it will drive 250mph off road. Lol
Thanks. Good luck with your rc project. I've put thumbs and gopros on rc trucks before and the only issue for me was it's a bit bumpy. I guess you can stabilize footage but I like the bumps and jostled look of it like it shows the speed. Have fun out there 🤟😎🤘
I actually have done it posted on my channel. very fun footage! It aint the smoothest due to me having a 1/16 rc truck with no dampening but still awesome seeing what your truck sees when you're out on a run
Very good, be careful if using on a Runcam as the wiring is reversed.
Yes, in the video I tell everyone about the way runcam does that😸 definitely wanna be careful
Hey! What type of connector do you use for the Thumb? The white plug, I mean. Not the battery end, the camera end. I need to buy some!
It's a 2pin jst
In the description I have some links, the 1st one is the part that has that piece plus a 5v regulator.
But aren't you now discharging your 2S Lipo unballanced, because you pulled out the one wire in the middle on your balance plug? Or am I missing something?
Kind regards
Honestly I'm not entirely sure why but they never seem to go out of balance. Also I always balance charge them anyways
@@lillygodzilly Okay, great. Thank you very much! :-)
@@DerGraf1901 no problem
If you’re only using the positive and negative on the balance plug for a 2s 3s or higher you’ll only be pulling the voltage equally just like using reg power leads xt30 or jst etc. now if you were accidentally using one of the balance wires and the negative you would actually be pulling 3.7 volts. Or in other words just one of the cells. Then yes you would be unbalancing the pack. So just make sure you are only using pod/neg off the balance connector. On a 2s it’s usually the red wire and the black wire. Middle wire probably is blue but sometimes red which is the balancing wire. 2s pos/neg are usually the 2 outside wires. (In my experience) great video btw.
@@jeffro1005This totally makes sense. Thank you very much for the great explanation!