watched the whole thing and I say thanks for sharing your trials on your journey ! I have many hobbies and each one has those same learning curves! I have not taken the plunge on jewelry yet so the tools needed is always a big thing for me. Im a journeyman carpenter, so tools make a major difference! "you get what you pay for" usually has truth to it. thanks again, Kenny. Edmonton, Alberta, Canada
Thanks very much for your comments! Definitely a learning curve when learning & usually more than 1 way to do things! I appreciate your interest & support! 🙏😊
I have been soldering electronics for 55 years. The brass or copper wool works better for cleaning the tip than the damp sponge, and the "wool" is softer than the iron plating on a good quality tip, so it will not damage it. Take my word for this! If you do use a tip cleaning sponge you should buy it from somewhere the caters to electronics hobbiists because an ordinary kitchen sponge might seem to work but may contain chlorine or sulphur compounds that will prematurely damage the tip and take the plating off of it. It's best to use distilled water because even well water has minerals in it, and city water will have chlorine compounds added as well. I've never been that impressed with the sal ammoniac tip cleaning block but the little can of tip cleaner contains a similar caustic chemical, as well as having powdered solder mixed in with it, and it works just fine; but I would caution not to overuse the tip cleaner and only use it when you really need to because the copper or brassful or sponge won't get the tip shiny and bright. The caustic of chemicals in any type of tip tinner will tend to eventually take the iron plating off of the copper tip and then it will corrode and dissolve into the molten soldier and flux. PS, It's very important to note that lead-free solder of any type, especially if silver is added to it, will have a higher melting point than the lead-tin solder that was traditionally used for electronics, and therefore the iron needs some extra thermal mass and heat transfer capacity as well as a higher temperature for this type of jewelry or stained glass work than you would need if you were merely soldering electronics with lead-based solder. The higher temperatures and the acidic fluxes used for jewelry work are riugh in tips, And buying cheap bowl pack tips directly from China or Asia via Amazon, Temu, Fleabay, Bangood, or AliExpress and the like is sure to lead to disappointment. I just had a brain flash: A good place to buy soldering equipment affordably, both used and new, and actually examine it in person and ask questions of the seller, would be at ham radio fests which will be invariably be peopled with hundreds of old codgers like myself who've been soldering for many decades. Chances are good you can find some reliable soldering gear cheaply enough that you could buy several different pieces of equipment to experiment with and still spend relatively little money.
I remember you posting about your frustrations with this process. Glad you were able to work through the issues and succeed! Thanks for the video and the helpful tips.
The struggle was Real 🤣🤣🤣 Thx so much & I’m happy to share what I’ve learned even if it’s helps just 1 person! Thx so much for your comment & support! 🙏😊💙
Really enjoyed your video and all the great info! Info for you -- the silver in the solder is not Argentium (you mentioned it as the common mispronunciation "argentINium," with an extra syllable). It is marked "Argent" because the metals are in three languages, the last one of which is French and argent is an old word for silver in French. The 4% can best be described as "fine" silver, as it cannot be sold in the US as an alloyed silver without stating the alloy. Just for what it's worth, and I hope you find this info useful and not critical; we're all learning! And now I'm moving on to your next video!
Great! I’m glad you got something out of it! Thank you for explaining the correct pronunciation & added info! I love learning & appreciate your knowledge as well! Thx for your support! 🙏😊
Great video, Karen! Lot's of very helpful information. 👍 Yes, I also learned about the different colored backings on the copper foil tape. Good to know. Also they have precut decorative border tape, but I think cutting it by hand gives you more creative freedom and form as well. Only recently did I find copper foil tape in 1,2,4,& even a 6 inch wide tape! Also found 8 1/2×11 inch sheets with the sticky backing. Maybe bigger than what some people might use,...but I was excited about the possibilities in ways I could use it. Lol,...so that's on the 'to order later' list.😅 I started with the cheap low wattage soldering iron, it was a cheaper investment kust to dop my creative toes in the pool so to speak. It was good I did it that way, because I ruined quite a few tips until I learned what solder n flux worked and also got the hang of proper tip maintenance and care. I'm glad that I didn't invest in an expensive Weller to start, and now, also glad I didn't get the station. That would be very disappointing to have those issues with an expensive unit!! I think with the Hakko, it makes sense to have the rheostat/ temp control in the handle itself. It saves your workspace too, not having the big units. I've seen several people working with great success with it, and actually I haven't heard anyone complain about it either, so good to know. I also have bought several of Laura Beth Love's books about the soft soldering for jewelry, and they are great too. She also has a CZcams channel. I think your video is going ro help people avoid alot of frustration. That learning curve can be frustrating, but also discouraging and expensive! I had to laugh when you said you don't like being limited😂😂😂,....a woman with a creative heart like my own! So glad you were determined to learn what you wanted to do and stuck with it. You do beautiful work, and thank you for sharing all your tips n tricks n knowledge you've acquired !😊👍💖
@@vivmestdagh7664 you are very welcome! I’m glad you found the video helpful. I was also extremely nervous to start the journey, but it’s not as scary as it looks! I appreciate your interest and support. 🙏😊💖
@@karensintuitivejewelry Thank YOU, Karin. Great that you share your knowledge with the world. And I love listening to you. You are so honest. And if you tell us that you cried out if frustration sometimes, you make me smile and go “oh, I totally get that…. “. You are funny. 💞💞💞💞
Hi Karen…great video-I learned A LOT!! You have been thru it girl with this soldering!! A real testament to you is how easy you make it look when there is so much to it!!!! Thank for explaining your experience and the entire process!! Hugs
Thx sooo much for your feedback, it was a LOT! 🤣 There’s so much more I plan to cover in the coming videos! Hope all is well with you & yours! Thx for your continued support! 🙏😊🇺🇸
Hi Karen. Thank you so much for this video. It was more helpful than several of the books that I have purchased since you were able to show the issues you had. I look forward to more videos.
Thank you kindly, I’m so happy you gained some help as I was worried I wasn’t making much sense! 🤣 There’s so much more learned experience I have to share in the future & hope you can learn other techniques from my other tutorials so please check them out! 🙏😊💜
Thank you so much for your helpful video! I really appreciate all your research! You are so thorough and diligent! Amazon should hire you to test the products!!!
Yes I have ALL her books, subscribe to her channel & have had a few message exchanges with her to gain more knowledge! I’m happy you found some useful information in this video! Thx for your support! 🙏😊💜
Hi Karen I found my problem was thinner, my solder would work until I used thinner. I think tips aren’t well made but regular tinning makes the solder work like a charm.
@@kemiagbato7402 copper is the Best metal to solder on so if it’s not sticking it might be coated with something or be heavily tarnished! Try sanding a small area, flux & try again. Also hold your iron on for a few seconds to allow the metal to get hot enough to accept the solder!
Great! Thank you! I’m thrilled to hear that the videos are helpful! Burnishing tools help press down & then smooth the copper foil tape into your piece to make a strong & smooth connection! After all this tape is what the solder goes on & the only thing that keeps your piece together! You can use a variety of “burnishing tools” such as popsicle sticks, cuticle sticks, fingernail, metal, stone, plastic burnishing tool or anything with a smooth surface! Thx for your interest & support! 🙏😊💚
@@bcwbarb If you can’t yet afford the 67 watt Hakko FX601-02 I would wait until you can instead of getting a cheaper one! I went through 7 irons in total frustration because I couldn’t afford the more expensive ones but in the end I spent more💰by trying not to spend more 💰🤣🤣🤣 Here’s the link…a.co/d/7oXzhxk
If it's less than $100 its not a real Hakko, it's a clone or counterfeit; it might be okay for electronics work (printed circuit boards) but it might not do the job well for stained glass work where you have a lot of copper foil that quickly wicks away the heat. You'll probably need something on the upper end of the wattage scale (80 to 100 watts), and most cheap soldering irons or stations won't included high-quality tips of the correct shape ( chisel shape, and plated copper, not fully iron or steel).
@@karensintuitivejewelry, Harbor Freight sells a soldering station for $45 that is surprisingly good for electronics work (I reviewed it on my channel), but at 50 W it's probably not sufficient for stained glass work. They sell a digital 90 W soldering station that sells for $125, And if it's as well built and well thought out as the $45 unit then it's probably very good bye but I think they only include pointy conical tips (no chisel tip) made of solid iron with it, and so replacement tips more suitable for stained glass work would be in order. It uses the standard 900 M/T18 type tips.... I am thinking of buying one of these and doing a review on it when I get a chance. At least if someone purchases one of these locally for stained glass work and it doesn't do the job then you can just bring it right back for a refund; easier than returning stuff to China!
I believe I have the same soldering iron you ended up preferring (hakko)! I don't love the wedge tip though...were you eventually able to find any other tips that are compatible?
I believe it was the less expensive soldering irons that didn’t get or keep the higher temperatures! With regards to the solder not sticking to the copper…knowing & understanding more now than I did back then, I wasn’t allowing the copper sheet metal to get hot enough to accept the solder! I do understand now that you have to be more patient to allow the piece whether it’s wire, sheet or the underlying soft solder to get up to a working temperature! Thx for your interest! 🙏😊💖
@@karensintuitivejewelry thanks for the reply! I just found your channel and even though I don’t do this kind of art, it looks real interesting and looks like I could do some beautiful pieces with my resin creations. But I am a beginner and was wondering what things to keep in mind when giving this a try! Thank you 😊 You do beautiful jewelry!
@@karensintuitivejewelry I enjoyed your content 😊 what will happen if I use a solder with lead? You only recommend using lead free because some of people might be allergic to lead? Or is there any particular reason?
@@miladmohamadaleiha5196 a lot of products containing lead have been Banned in many countries for decades because lead is considered highly toxic to health & environment & is a known carcinogen! It’s not about being allergic! There’s a vast amount of information on the subject if you’re interested! Better to be safe than sorry! It’s a very common practice to only use lead-free solder for jewelry making! Solder containing lead is used in electronics & other art projects such as stained glass!
@@karensintuitivejewelry hi karen…i did my first piece last night but some of it turns yellow and seems dirty…what should i do after my soldering is done?
@@miladmohamadaleiha5196 did you wash your soldered piece with warm water & Dawn dish soap using a toothbrush? What solder are you using? What flux are you using? What soldering iron are you using? What temperature is your iron set on? What kind of copper foil tape are you using?
Weller isn't German, they're owned by Cooper Tool division of Apex Corporation. They have manufacturing plants, or contracts with other factories, all over the world but much of their equipment is made in China or Asia nowadays; they're not the same Weller USA I knew as an electronics-nerd kid in the 1960's and 70's, and their "red line" of tools, sold at big-box home improvement stores, is their cheapest and cheesiest gear. Your red Weller works okay for your purposes because it has a large heater, a fat tip ( perhaps made of copper👍), and therefore plenty of *thermal mass*; but the red soldering station they sell at Home Dumpo for $55 is a piece of junk, even for light duty electronics work, and included junky conical (pointy) tips made of solid iron ( The base metal should be solid copper with a plating or coating of iron only at the pointy business end). For medium and heavy duty soldering, an iron with thermal feedback/temperature regulation is pretty much a necessity, and a cheapo modern Weller won't do the job well, if at all. Your blue Weller is a decent machine, for electronics use anyway, but despite being marked "85 watts", the actual heating element is rated at 70 watts, and the additional 15 watts is consumed (wasted) by the digital circuitry. Unfortunately, Weller seriously demean the brand, and frustrate newbie hobbyists, by selling inferior products for less, and/or by not giving accurate specifications.
How helpful! Sharing the “fail” items is so good!
Glad it was helpful! I appreciate your interest & support! 🙏😊💖
watched the whole thing and I say thanks for sharing your trials on your journey ! I have many hobbies and each one has those same learning curves! I have not taken the plunge on jewelry yet so the tools needed is always a big thing for me. Im a journeyman carpenter, so tools make a major difference! "you get what you pay for" usually has truth to it. thanks again, Kenny. Edmonton, Alberta, Canada
Thanks very much for your comments! Definitely a learning curve when learning & usually more than 1 way to do things! I appreciate your interest & support! 🙏😊
I have been soldering electronics for 55 years. The brass or copper wool works better for cleaning the tip than the damp sponge, and the "wool" is softer than the iron plating on a good quality tip, so it will not damage it. Take my word for this! If you do use a tip cleaning sponge you should buy it from somewhere the caters to electronics hobbiists because an ordinary kitchen sponge might seem to work but may contain chlorine or sulphur compounds that will prematurely damage the tip and take the plating off of it. It's best to use distilled water because even well water has minerals in it, and city water will have chlorine compounds added as well. I've never been that impressed with the sal ammoniac tip cleaning block but the little can of tip cleaner contains a similar caustic chemical, as well as having powdered solder mixed in with it, and it works just fine; but I would caution not to overuse the tip cleaner and only use it when you really need to because the copper or brassful or sponge won't get the tip shiny and bright. The caustic of chemicals in any type of tip tinner will tend to eventually take the iron plating off of the copper tip and then it will corrode and dissolve into the molten soldier and flux.
PS, It's very important to note that lead-free solder of any type, especially if silver is added to it, will have a higher melting point than the lead-tin solder that was traditionally used for electronics, and therefore the iron needs some extra thermal mass and heat transfer capacity as well as a higher temperature for this type of jewelry or stained glass work than you would need if you were merely soldering electronics with lead-based solder. The higher temperatures and the acidic fluxes used for jewelry work are riugh in tips, And buying cheap bowl pack tips directly from China or Asia via Amazon, Temu, Fleabay, Bangood, or AliExpress and the like is sure to lead to disappointment.
I just had a brain flash: A good place to buy soldering equipment affordably, both used and new, and actually examine it in person and ask questions of the seller, would be at ham radio fests which will be invariably be peopled with hundreds of old codgers like myself who've been soldering for many decades. Chances are good you can find some reliable soldering gear cheaply enough that you could buy several different pieces of equipment to experiment with and still spend relatively little money.
Thx for your opinions
I remember you posting about your frustrations with this process. Glad you were able to work through the issues and succeed! Thanks for the video and the helpful tips.
The struggle was Real 🤣🤣🤣
Thx so much & I’m happy to share what I’ve learned even if it’s helps just 1 person! Thx so much for your comment & support! 🙏😊💙
Really enjoyed your video and all the great info! Info for you -- the silver in the solder is not Argentium (you mentioned it as the common mispronunciation "argentINium," with an extra syllable). It is marked "Argent" because the metals are in three languages, the last one of which is French and argent is an old word for silver in French. The 4% can best be described as "fine" silver, as it cannot be sold in the US as an alloyed silver without stating the alloy. Just for what it's worth, and I hope you find this info useful and not critical; we're all learning! And now I'm moving on to your next video!
Great! I’m glad you got something out of it! Thank you for explaining the correct pronunciation & added info! I love learning & appreciate your knowledge as well! Thx for your support! 🙏😊
Thank you so much for sharing your journey!! So helpful and you are just lovely 😊
Thank YOU for your interest & support! I’m thrilled you find my videos helpful! 🙏😊💖
Great video, Karen! Lot's of very helpful information. 👍 Yes, I also learned about the different colored backings on the copper foil tape. Good to know. Also they have precut decorative border tape, but I think cutting it by hand gives you more creative freedom and form as well. Only recently did I find copper foil tape in 1,2,4,& even a 6 inch wide tape! Also found 8 1/2×11 inch sheets with the sticky backing. Maybe bigger than what some people might use,...but I was excited about the possibilities in ways I could use it. Lol,...so that's on the 'to order later' list.😅
I started with the cheap low wattage soldering iron, it was a cheaper investment kust to dop my creative toes in the pool so to speak. It was good I did it that way, because I ruined quite a few tips until I learned what solder n flux worked and also got the hang of proper tip maintenance and care. I'm glad that I didn't invest in an expensive Weller to start, and now, also glad I didn't get the station. That would be very disappointing to have those issues with an expensive unit!!
I think with the Hakko, it makes sense to have the rheostat/ temp control in the handle itself. It saves your workspace too, not having the big units. I've seen several people working with great success with it, and actually I haven't heard anyone complain about it either, so good to know.
I also have bought several of Laura Beth Love's books about the soft soldering for jewelry, and they are great too. She also has a CZcams channel. I think your video is going ro help people avoid alot of frustration. That learning curve can be frustrating, but also discouraging and expensive!
I had to laugh when you said you don't like being limited😂😂😂,....a woman with a creative heart like my own! So glad you were determined to learn what you wanted to do and stuck with it. You do beautiful work, and thank you for sharing all your tips n tricks n knowledge you've acquired !😊👍💖
Thx so much! It makes me happy to hear that the videos are useful! I appreciate your comments & continued support! 🙏😊💜
Thank you so much, Karen! Very helpful! I want to start soldering, so I am a little bit nervous. There is a lot to think about!
@@vivmestdagh7664 you are very welcome! I’m glad you found the video helpful. I was also extremely nervous to start the journey, but it’s not as scary as it looks! I appreciate your interest and support. 🙏😊💖
@@karensintuitivejewelry Thank YOU, Karin. Great that you share your knowledge with the world. And I love listening to you. You are so honest. And if you tell us that you cried out if frustration sometimes, you make me smile and go “oh, I totally get that…. “. You are funny. 💞💞💞💞
Hi Karen…great video-I learned A LOT!! You have been thru it girl with this soldering!! A real testament to you is how easy you make it look when there is so much to it!!!! Thank for explaining your experience and the entire process!! Hugs
Thx sooo much for your feedback, it was a LOT! 🤣 There’s so much more I plan to cover in the coming videos! Hope all is well with you & yours! Thx for your continued support! 🙏😊🇺🇸
Hi Karen. Thank you so much for this video. It was more helpful than several of the books that I have purchased since you were able to show the issues you had. I look forward to more videos.
Thank you kindly, I’m so happy you gained some help as I was worried I wasn’t making much sense! 🤣 There’s so much more learned experience I have to share in the future & hope you can learn other techniques from my other tutorials so please check them out! 🙏😊💜
Thank you Thank you Thank you!!!
I'm Just learning too and have been sooo confused about which wire to use...This helps so much!
I’m thrilled to hear you found the video helpful! It sure can be overwhelming! I appreciate your support! 🙏😊💖
You are an angel! I am joining in on the soft soldering journey and this video covers EXACTLY my initial questions. Thank you for sharing ❤
Ahhhh thank you kindly! I appreciate your lovely comments! I’m thrilled you have found my tutorials helpful! 🙏😊💜
Thank you so much for your helpful video! I really appreciate all your research! You are so thorough and diligent! Amazon should hire you to test the products!!!
Glad it was helpful! Thank you so much! I really appreciate your interest & support! I’d be happy to get paid by Amazon for my reviews 😂🤣
Hilarious!!! epic introduction, super helpful, super funny as I get your frustrations!!! Thank you for your time and perseverance!
Glad you enjoyed it! I appreciate your support! 🙏😊💖
Her name is Laura Beth Love. Thank you for all the awesome tips!
Yes I have ALL her books, subscribe to her channel & have had a few message exchanges with her to gain more knowledge! I’m happy you found some useful information in this video! Thx for your support! 🙏😊💜
So very helpful!
Glad it was helpful! I appreciate your interest & support! 🙏😊💖
Hi Karen I found my problem was thinner, my solder would work until I used thinner. I think tips aren’t well made but regular tinning makes the solder work like a charm.
Not certain what exactly you’re referencing….thinner? I do appreciate your support! 🙏😊
@@karensintuitivejewelry tinner, it cleans the tip and makes it shiny.
@@stellau3028 oh ok! Gotcha! Keeping a clean tip is important for the health & longevity of the tip! Thanks for your interest & support! 🙏😊💖
Thank you for this video. Going through the same issues. Sometimes the solder won't even flow.
It’s so frustrating, isn’t it! 😡 You’ll get there! I appreciate your interest & support! 🙏😊💖
@@karensintuitivejewelry Please do you have any tips for soldering on copper sheets. the solder just flakes off for me
@@kemiagbato7402 copper is the Best metal to solder on so if it’s not sticking it might be coated with something or be heavily tarnished! Try sanding a small area, flux & try again. Also hold your iron on for a few seconds to allow the metal to get hot enough to accept the solder!
Me to, want to just have fun like cindi lauper says in her soong :" Girls just want to have fun " lol 😂❤ thanks so much!
😂😂😂
Found ur vid enormously helpful, ty for sharing your journey learning what works and doesn't and explaining everything tyty huggles
Awesome! Thanks so much! I’m happy you found it helpful! I appreciate your comments & continued support! 🙏😊💖
I really enjoyed your video Karen great job pilgrim 👍
Thanks so much 😊 Glad you enjoyed it! I appreciate your interest & support! 🙏😊
You’re amazing!
Ahh you’re sweet! Thank you kindly! I appreciate your interest & support! 🙏😊💖
Amazing video! Super informative and helpful. Thank you 🙏🏽🙏🏽🙏🏽
Thank you so much! I’m thrilled you found it useful! Thx for your support! 🙏😊💖
THANK YOU, I'M, JUST STARTING OUT. SUPER HELPFUL INFORMAITON.
Thank You! I’m so happy that you found some useful information here! I appreciate your comment & your interest! 🙏😊
Thanks!
Thank You! Thank You! Thank You! I appreciate your support so much!
Thank you so much. I have learned a lot from you.
Oh thank YOU! I’m so happy that you benefited from it, I never really know unless someone comments! I’m grateful for your feedback & interest! 🙏😊💜
Great information, very helpful.
I’m happy you found this video helpful! The 1st year was a Super Struggle! 🙏😊💜
Excellent video . Learned alot. Thank you!!
Awesome! I’m thrilled that you found this helpful! 🙏😊🧡
That was amazing thank you so much I really do want to try this ❤
Ah thank YOU! 🙏😊
Awesome information
Thx very much! I’m thrilled you found some information helpful!
What a great video. Thanks a lot!
Glad you liked it! I appreciate your interest & support! 🙏😊💖
Hi! Your videos have been so helpful!thnkyouuu♥️
Also can you please tell what are burnishing tools used for
Great! Thank you! I’m thrilled to hear that the videos are helpful! Burnishing tools help press down & then smooth the copper foil tape into your piece to make a strong & smooth connection! After all this tape is what the solder goes on & the only thing that keeps your piece together! You can use a variety of “burnishing tools” such as popsicle sticks, cuticle sticks, fingernail, metal, stone, plastic burnishing tool or anything with a smooth surface! Thx for your interest & support! 🙏😊💚
@@karensintuitivejewelry much Thnks ! And for detailed answer ❤️!
Found 9 soldering irons on Amazon made by Hakko. Think I'm going to get the intermediate one as I can't afford the ones over $100.
@@bcwbarb If you can’t yet afford the 67 watt Hakko FX601-02 I would wait until you can instead of getting a cheaper one! I went through 7 irons in total frustration because I couldn’t afford the more expensive ones but in the end I spent more💰by trying not to spend more 💰🤣🤣🤣
Here’s the link…a.co/d/7oXzhxk
If it's less than $100 its not a real Hakko, it's a clone or counterfeit; it might be okay for electronics work (printed circuit boards) but it might not do the job well for stained glass work where you have a lot of copper foil that quickly wicks away the heat. You'll probably need something on the upper end of the wattage scale (80 to 100 watts), and most cheap soldering irons or stations won't included high-quality tips of the correct shape ( chisel shape, and plated copper, not fully iron or steel).
@@karensintuitivejewelry, Harbor Freight sells a soldering station for $45 that is surprisingly good for electronics work (I reviewed it on my channel), but at 50 W it's probably not sufficient for stained glass work. They sell a digital 90 W soldering station that sells for $125, And if it's as well built and well thought out as the $45 unit then it's probably very good bye but I think they only include pointy conical tips (no chisel tip) made of solid iron with it, and so replacement tips more suitable for stained glass work would be in order. It uses the standard 900 M/T18 type tips.... I am thinking of buying one of these and doing a review on it when I get a chance. At least if someone purchases one of these locally for stained glass work and it doesn't do the job then you can just bring it right back for a refund; easier than returning stuff to China!
I believe I have the same soldering iron you ended up preferring (hakko)! I don't love the wedge tip though...were you eventually able to find any other tips that are compatible?
Yes I ordered these 2 additional tips when I purchased the iron. They are for the Hakko FX-601
amzn.to/4b8g62r
amzn.to/3QheWtB
Why was the liquid flux not working for you initially? Why was the soldering not sticking to your piece?
I believe it was the less expensive soldering irons that didn’t get or keep the higher temperatures!
With regards to the solder not sticking to the copper…knowing & understanding more now than I did back then, I wasn’t allowing the copper sheet metal to get hot enough to accept the solder! I do understand now that you have to be more patient to allow the piece whether it’s wire, sheet or the underlying soft solder to get up to a working temperature! Thx for your interest! 🙏😊💖
@@karensintuitivejewelry thanks for the reply! I just found your channel and even though I don’t do this kind of art, it looks real interesting and looks like I could do some beautiful pieces with my resin creations. But I am a beginner and was wondering what things to keep in mind when giving this a try! Thank you 😊
You do beautiful jewelry!
I prefer using thinner solder.
Everybody has their favorite
Do you have to "pickle" the pieces when finished?
No pickling with Soft solder. Only cleaning required is typically dish soap & warm water.
How long will the solder last on the ring?
The solder will last forever! It is not a temporary application.
Is it necessary to use Lead free solder?
Yes 100% if making jewelry! Lead solder is only used in stained glass or other artwork! Thx for your interest & support! 🙏
@@karensintuitivejewelry I enjoyed your content 😊 what will happen if I use a solder with lead? You only recommend using lead free because some of people might be allergic to lead? Or is there any particular reason?
@@miladmohamadaleiha5196 a lot of products containing lead have been Banned in many countries for decades because lead is considered highly toxic to health & environment & is a known carcinogen! It’s not about being allergic! There’s a vast amount of information on the subject if you’re interested! Better to be safe than sorry! It’s a very common practice to only use lead-free solder for jewelry making! Solder containing lead is used in electronics & other art projects such as stained glass!
@@karensintuitivejewelry hi karen…i did my first piece last night but some of it turns yellow and seems dirty…what should i do after my soldering is done?
@@miladmohamadaleiha5196 did you wash your soldered piece with warm water & Dawn dish soap using a toothbrush? What solder are you using? What flux are you using? What soldering iron are you using? What temperature is your iron set on? What kind of copper foil tape are you using?
Weller isn't German, they're owned by Cooper Tool division of Apex Corporation. They have manufacturing plants, or contracts with other factories, all over the world but much of their equipment is made in China or Asia nowadays; they're not the same Weller USA I knew as an electronics-nerd kid in the 1960's and 70's, and their "red line" of tools, sold at big-box home improvement stores, is their cheapest and cheesiest gear. Your red Weller works okay for your purposes because it has a large heater, a fat tip ( perhaps made of copper👍), and therefore plenty of *thermal mass*; but the red soldering station they sell at Home Dumpo for $55 is a piece of junk, even for light duty electronics work, and included junky conical (pointy) tips made of solid iron ( The base metal should be solid copper with a plating or coating of iron only at the pointy business end). For medium and heavy duty soldering, an iron with thermal feedback/temperature regulation is pretty much a necessity, and a cheapo modern Weller won't do the job well, if at all. Your blue Weller is a decent machine, for electronics use anyway, but despite being marked "85 watts", the actual heating element is rated at 70 watts, and the additional 15 watts is consumed (wasted) by the digital circuitry. Unfortunately, Weller seriously demean the brand, and frustrate newbie hobbyists, by selling inferior products for less, and/or by not giving accurate specifications.
Thx for your input
Way too much filler talking😪
Oh well lol
Very helpful video, thank you very much
I’m thrilled to hear you found the video. Helpful! I appreciate your support! 🙏😊💖