Bro, i just realized there was a smoked version of this 😮. I just recently ordered mine and now i will return it to get them smoked one. Thank god i saw this video haha. The smoked ones look waaaay better although the clear one’s might illuminate brighter.
@@Schizyy DUNTUO Side Mirror Light Led Turn Signal Dynamic Sequential Blink Car Lights Running Indicator Marker Lamps for Infiniti Q50 Q60 Q70 QX30 QX50 QX60 QX70 [Smoked Lens] Left Right Assembly a.co/d/cjTXLki
Wired the blue for the puddles, worked for a little bit. But now my window is weak and wont roll up. Goes all the way down when I open my door have to close it from the passenger side when I get out and the puddle stopped working. Maybe it shorted something? Not sure need to rewire it.
Did you hard wire it to the blue wire ? If you didn’t sometimes it gets loose and can cause a short in your Window switch and window actuator. You’ll have to get them both replaced. It happens on another q60 I had
Also the 2 blue connectors inside door...why are those disconnected, confused as to connection after wires are pulled thru upper door grommet,,,Can U help have sequentials on the way!!!
You disconnect it in order to be able to pull them up throw the upper grommet and tape the wires for the sequential you are installing down that is it!
Yo bro sick video so I had my lights installed. But I noticed today that I don’t have a white light it’s just the sequential with hazard and turn signal. They gave me back my old lights and in the box was the blue black white extension cords still wrapped up. Wtf 😑 did they fuck sumthing up or they just need to put the extension cord in? Any advice would help. Thanks again!
Yooo thanks brotha! And it sounds like they did not tape the blue and white wire because the red and yellow wire are for the Switchback(turn signal/hazards)
How did you get the wires into the car (to the RGB controller)? Are the wires exposed when you open the door or did you route through the rubber wire boot?
What’s up man! Just ordered these I saw on 11:37 that you cut that white wire to go with the blue, so with the blue wire did you cut an open gap in order to get the white one in between? Asking ahead of time! Thx.
Yessssir that’s it! To make it easier just cut the blue wire in half. Splice both ends, and then splice a single end on the white one and from there just twist the blue and white wire together with the second blue wire end.
Is there a DDS light that comes on the dash after you installed the coilovers on the redsport? I currently have lowering springs but want to switch to coilovers.
I wired it same way as you but I don’t know if I shorted something, my driver window goes down but won’t go up but all other buttons work on the switch even passenger window. Any suggestions? I’ve checked all fuses and window mower works
This is one best video so far. Thanks for showing how to do the puddle lights
No problem! Gonna be uploading the RGB install soon too
@@Speedycory6did you ever do a rgb install vid?
Bro, i just realized there was a smoked version of this 😮. I just recently ordered mine and now i will return it to get them smoked one. Thank god i saw this video haha. The smoked ones look waaaay better although the clear one’s might illuminate brighter.
Yes! The smoked ones look fire in my opinion 🔥
Where'd you guys order these from?
@@Speedycory6 ^
@@Schizyy DUNTUO Side Mirror Light Led Turn Signal Dynamic Sequential Blink Car Lights Running Indicator Marker Lamps for Infiniti Q50 Q60 Q70 QX30 QX50 QX60 QX70 [Smoked Lens] Left Right Assembly a.co/d/cjTXLki
@@Speedycory6 I ordered this brand before seeing this comment and glad I picked the same one as you 😅
Heat the mirror cap with a heat gun or hair dryer gently not to hot and that will help with it not breaking
is it possible to just have the startup animation but no DRL?
Best video out!! Clean as Heck!!
Wired the blue for the puddles, worked for a little bit. But now my window is weak and wont roll up. Goes all the way down when I open my door have to close it from the passenger side when I get out and the puddle stopped working. Maybe it shorted something? Not sure need to rewire it.
Did you hard wire it to the blue wire ? If you didn’t sometimes it gets loose and can cause a short in your Window switch and window actuator. You’ll have to get them both replaced. It happens on another q60 I had
Yeah I know my next purchase.Clean af
Why didn’t you go with the V2 mirror caps?
Got these ones for free 🫠
Also the 2 blue connectors inside door...why are those disconnected, confused as to connection after wires are pulled thru upper door grommet,,,Can U help have sequentials on the way!!!
You disconnect it in order to be able to pull them up throw the upper grommet and tape the wires for the sequential you are installing down that is it!
My kit didn’t come with any blue wiring. Is it needed?
Yo bro sick video so I had my lights installed. But I noticed today that I don’t have a white light it’s just the sequential with hazard and turn signal. They gave me back my old lights and in the box was the blue black white extension cords still wrapped up. Wtf 😑 did they fuck sumthing up or they just need to put the extension cord in? Any advice would help. Thanks again!
Yooo thanks brotha! And it sounds like they did not tape the blue and white wire because the red and yellow wire are for the Switchback(turn signal/hazards)
So when car is locked puddle lights stays on all the time. Is this with door locked or unlocked
Do you have the links for the sequential and mirror caps?
They have them on southbayautoworkz
How did you get the wires into the car (to the RGB controller)? Are the wires exposed when you open the door or did you route through the rubber wire boot?
Mine are exposed but I wrapped it in electrical tape and this oem loom tape.
a.co/d/1kaUgXn
damn i need that asap. looks dope!
What’s up man! Just ordered these I saw on 11:37 that you cut that white wire to go with the blue, so with the blue wire did you cut an open gap in order to get the white one in between? Asking ahead of time! Thx.
Yessssir that’s it! To make it easier just cut the blue wire in half. Splice both ends, and then splice a single end on the white one and from there just twist the blue and white wire together with the second blue wire end.
Bruh there’s is no way you gotta do all this🥲🥲I just order some M3 Caps and smoked sequentials😰
Ong 😂
Where did you get the sequentials?
I love the drl light but the fitment ain’t the best
Is there a DDS light that comes on the dash after you installed the coilovers on the redsport? I currently have lowering springs but want to switch to coilovers.
Nope it doesn’t come on at all. I have no lights or anything on currently. And I’ve had it for about 2 1/2 months
@@Speedycory6 nice that's awesome! BC coilovers right?
I got the driver side to work, I cant get the passenger side, what wires to use?
It should be the same thing on the driver. Maybe one of the connections aren’t properly grounded
@@Speedycory6 we gave up after 2 days and just ran a wire from passenger to driver side and hooked it up that way
I wired it same way as you but I don’t know if I shorted something, my driver window goes down but won’t go up but all other buttons work on the switch even passenger window. Any suggestions? I’ve checked all fuses and window mower works
Yea you actually shorted out the window actuator. It has happened to me as well but only with the RGB sequential. You have to replace unfortunately!
@@Speedycory6 thanks, I ordered a extra master switch cause I thought it was the switch, if that doesn’t work I’ll order a used window actuator.
@@jimmyt6379any updates currently going through the same problem and i’m going crazy 😂
@@miguel-vx8ew yea it ended up being the window switch itself, I ordered a new one from eBay and swapped the switch and started working again
@@jimmyt6379 can u share the window switch link u bought ?
I only connected blue to purple and it didnt work
for the drl was I missing a step or anything I should do? I did a t tap into the purple one I didnt actually connect it in the little clip
Bro what about the other side.? Is the same connection ?
Yeap same exact thing Brotha. Same color wires and eveything.
Not finna lie I have a 2021 and this did not work 😢
Q60 redsport 2021
It probably a different harness than the older Q60s
beautiful ride …u gotta do a chrome delete asap!!!!
Thank you brotha! 🙌🏽🙏🏽 and yesss man I need to asap! Been saying the same thing! Hah
Don't waste time getting this product a simple plug and play is available no wiring on the side view mirrors
Where can I get
This is the most dumbest explanation ever smh
I got aids reading this comment