Hello. Thank you for posting your comment. Yes, you are correct. How ever it would be very difficult to get the exact timing so I ended up replacing the camshaft. Have a great day and God bless you 🙏
great video! my car has a p0340 code and I replaced the sensor and the pig tail and still throws the code nut only when I rev it up high or give it a lot of gas while driving. under normal driving with light to moderate throttle I get no check engine light.
Really cuz of your video i found my probem exactly cuz we were assuming its a bad pcm /ecu i have a 2.3 turbo mazda cx7 you saved me alot am really happy thumbs up 👍🏻 😊😊
Good question! The point of the video is to show you what the problem is and what you will need to do to fix the problem. Let me e know if you have any other questions. Have a great day and God bless you 🙏
Hello. That is a good question. Actually, yes you can drive it like that. However, it would be best to replace the camshaft for anew one or a known good part.
You help me a Lot, thank you so much 😂 !!!!!!
wasn't my problem but your description of the diagnostic gave me some great ideas of things to check
Thank you for the comment. Please keep me posted and God bless you
I had a similar problem I ended up changing the entire camshaft, though it took me weeks to discover.thanks
Bro thanks for the tip it work in mazda 3 i can thank u enough thanks a lot
I am glad to hear that the video helped you!
You could have drilled hole between that ring into the cam end and put in a basic spring pin to keep it from rotating again.
Hello. Thank you for posting your comment. Yes, you are correct. How ever it would be very difficult to get the exact timing so I ended up replacing the camshaft. Have a great day and God bless you 🙏
Excellent work mate , I wonder how many deg of tolerance there is .
mahalo for sharing this 👌🏽
helpful to rule out if it’s fuse, or relay ‘cause my battery I installed new.
Thanks for sharing the solution. Does it also occur on the Mazda 3 2007 with a z6 1.6 engine ?
My car just stops after 20 min with code P0340
Thanks
Thank you for the comment and God bless you 🙏
great video! my car has a p0340 code and I replaced the sensor and the pig tail and still throws the code nut only when I rev it up high or give it a lot of gas while driving. under normal driving with light to moderate throttle I get no check engine light.
Hello, keep me posted
@@gqautodiagnostics it ended up being the crank position sensor.
So helpful
Wow, very interesting. Thanks...
Thanks bro the car worked 🔥
Awesome 👌. Thank you for posting your comment. Job well done!
Really cuz of your video i found my probem exactly cuz we were assuming its a bad pcm /ecu i have a 2.3 turbo mazda cx7 you saved me alot am really happy thumbs up 👍🏻 😊😊
Good brother
Niceeeee. I love how you say thank you lord. We always must give thanks to Jesus or Lord
Thanks! Great video.
Could that problem ultimately cause motor to throw a rod if you're say stuck in the snow revving high revs
thx bro is work👍
How much was it to fix it
Mazda 2.3 can be a problem when you swap non drive by wire and cable throttle , they use different crankshaft pulley and cam shaft trigger .
I have a Mazda 3 2005 and my car won’t start what should I do?
You must check all the basics such as fuel pressure, spark and injector light, lastly compression to begin with. keep me posted.
how does that fix it? you made it run untill it doesnt again
Good question! The point of the video is to show you what the problem is and what you will need to do to fix the problem. Let me e know if you have any other questions. Have a great day and God bless you 🙏
So I guess it can't be driven like that. Didn't that fix it? Thanks!
Hello. That is a good question. Actually, yes you can drive it like that. However, it would be best to replace the camshaft for anew one or a known good part.
You can welding?
Hello, thank you for posting your question. No, you cannot. It would be best to replace it. Keep me posted and God bless you 🙏
Svp je veux en français
Código p0800 Mazda 3 2.3cc 2004
Hello. Thank you for posting your question. I do not see any definition for a P0800 code. What is the symptoms?