Nissan Sentra 1 4 Overheating Part 2 Cylinder Head Re Fit
Vložit
- čas přidán 28. 08. 2024
- website:- www.vehiclemai...
As promised in Part 2 of the Nissan Sentra Cylinder Head repair, it was an uphill battle to find a replacement cylinder head but I finally managed to source one that was all ready to go, enjoy, until next time Safe Motoring.
Gary
Lekke video Garry. Enjoyed this 2 part series. I wanted to give a possible recommendation. Use an oil stone to clean up the block surface. Very effective as I've learnt this from a local mechanic. Thank you
Thanks for the advice, Sathasivan I will take it under advisement.
Thank you for this video it was spot on
Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you.
Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA,
It is FREE.
I was waiting for this video after you mentioned there will be part 2....nice job
Thanks for your continued support Sipho it is greatly appreciated.
@@vehiclemaintenanceandrepai3790 one more thig please..do you have torque specs for Nissan 1400 engine?
See Time Stamp 7:56, torque specs are there, just pause the video and copy, Sipho.
@@vehiclemaintenanceandrepai3790 for 1400 ?
This a 1400 Sentra
I have a nissan sentra sabre that mixed oil and water took the top to engineering I can see the little mistakes I might have made while assembling it back now it mixed again cylinder nummber 4 doesnt fire anymore and it over heats badly the water does not circulate I am planning on taking it back to engineering for pressure testing. I just wanted to know if you would have any other recommendations on what else might be wrong
I would very much appreciate any feed back
Nice information keep itup
Thank you.
As always great work from you. Payen gaskets are good.
Thanks, Justin, only the best will give great results, not the cheapest but well worth it, your continued support is well appreciated.
Do you know why this engine overheated so badly? Thanks Gary🙏🏻👍🏻
A water pipe burst under the intake manifold causing the car to run out of sufficient coolant and caused the severe overheating.
Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you.
Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA,
It is FREE.
Great video buddy. Did you reuse the head bolts? Can us reuse torque to yield bolts? I have a Honda civic r18a engine.
use new bolts as I did
Can you please tell me where you eventually got the refurbished cylinder head, and how much it cost in rands?
I got it from a scrap yard in the Northern Suburbs of Cape Town (Brackenfell) around R2500.
@@vehiclemaintenanceandrepai3790 Thanks so much for your reply🙏🏻 I've got one of these Sentra 1.4 fuel injection 2001 model still in mint condition and I'm just worried that if I perhaps need a head in 10 years or whatever, if I'll be able to get one?😬🤷♂️🙋🏼♂️
@@labourlawact7826 All good, These are tough, reliable vehicles, spares are never a real problem with them in my experience and they seldom break down when well maintained, keep your hand on it and it will serve you well.
@@vehiclemaintenanceandrepai3790 Thanks buddy. Yeah, I've been maintaining it meticulously, replaced all water hoses, radiator and I change the oil every 10k kilometres with Castrol Magnatec. I'm in Simonstown, and will keep your details handy in case I have any problems. 🙏🏻👍🏻🙋🏼♂️
@@labourlawact7826 All Good.👌
Hi sir l like your work, can u please tell me what is the torque settings for the nissann sentra bubble shape 16V Dohc 95 model
Flywheel bolts 83/93 nm
Cy. head
1st 29 nm
2nd 59 nm
3rd loosen
4th 29 nm
5th 59 nm
Big Ends 1st 14/16 nm 2nd 35/40 degrees
main bearings 46/52 nm
OHC Bearing caps 9/12 nm
I hope this helps, thanks for supporting my channel with your visit.
Hi boss thank you for your help, I appreciate it. But now I have done everything and car starts perfectly but I have a miss on number 2 everything is new even the plug codes, what can it be because when I pull out all the plug codes the engine drops but not number 2
It could be a burnt valve, broken piston rings, or a leaking intake manifold near N0.2 cylinder, do a compression test 1st
Thank u very much sir
All good.
where you located i got a ga15de that likes to smoke
Cape Town in the Southern Suburbs.
Is this head gasket graphite?
No, it is not Justin, it looks it though.
T tích sưu gì 2l34wê
44444
?????????????????????????????