How to Find all the active IP in your Network - Advanced IP Scanner - Installation and Configuration

In this video I am showing how to install advanced IP Scanner and how to scan Active IPs in Your Network.
Note:
Advanced IP Scanner
Reliable and free network scanner to analyse LAN. The program shows all network devices, gives you access to shared folders, provides remote control of computers (via RDP and Radmin), and can even remotely switch computers off. It is easy to use and runs as a portable edition. It should be the first choice for every network admin.
If you have the following queries this video will be helpful:
1. How to Find all the IPs in your Network?
2. How to find MAC address of a specific IP?
3. How to find IP address from MAC address?
4. How to install advanced IP scanner?
5. How to use the advanced IP scanner?
6. Install ip scanner
7. How to install IP scanner
8. How to find dead and active IP in your network
9. Free IP scanning in Windows 10
10. How to find active IP list in the network? If you want to contribute me anything use this link : www.paypal.com...

[@HaNo-fk3iy]

Thanks

[@lindokuhlendzambo3427]

Thank you

[@reginaldpotts2037]

what would you type n the search bar to see ALL active network connections? I realise it will take some time to scan

[@fikrasuhendri2785]

how do you make the ip raspi no longer detected?
My Raspi IP is no longer detected, what are the other ways to detect the IP and be able to log in using the VNC viewer?
in the ip scanner application does not detect ip raspi, even though Raspi is connected using a LAN cable

[@TheTechnologyZone]

raspberry pi may not be in dhcp.

[@nb_acc_h]

Do you need a wireless wifi connection to do this?

[@dmario2992]

It only shows me the ip adresses but i want to know the devices how can i do that?

[@TheTechnologyZone]

You can find the devices by MAC IDs

[@dmario2992]

@@TheTechnologyZone it says is couldnt be found

[@TheTechnologyZone]

@@dmario2992 What could not be found?????

[@dmario2992]

@@TheTechnologyZone when i search for the mac adress a device couldnt be found

[@AeroAngle]

what about 172 through 192 is that possible?

[@ketanbhole8748]

How can u scan a specific radius like radar do ,all the avaliable devices ip in that radius ? Please help if u have any info about this 🙏

[@iMToufeeq]

I need help scanning a specific radius like radar does for all available devices' IP addresses. If you have any information about this, please let me know.

[@jasonbing156]

Doesn’t find all active IP users…

[@sh0t60]

lmao nice one im on your pc rn

[@TheSwedishGamerTim]

* C R I N G E *

[@butaff426]

Broo please help after i press download i cant install it

[@nnazia2790]

How can i fix the dead server problem?

[@TheTechnologyZone]

It will show only the active/running servers. For dead servers , you need to check the dns entries if u have a local dns.

[@nnazia2790]

I already checked. Flush dns and again register dns. But same thing happen to me. My raspberry pi server showing dead on ip scanner

[@TheTechnologyZone]

@@nnazia2790 Do you run a DHCP Server?

[@vivekdas3583]

Cant find more than .255
Any solution???

[@TheTechnologyZone]

yes, you can put initial and end ip

[@vivekdas3583]

@@TheTechnologyZone howww

[@TheTechnologyZone]

@@vivekdas3583 For example in the destination you can put 192.168.1.255 (in my case) , so it will search for 510 IPs in the provided range.

[@ali3743]

we can scan with port ? can you please tell me any software name we check all ip range with port

[@TheTechnologyZone]

externally or internally

[@ali3743]

@@TheTechnologyZone both

[@iMToufeeq]

Can you please tell me if there is any software we can use to scan all ip ranges with a port?

[@LeGenDzZ111]

Red

[@TheTechnologyZone]

??

[@DansEdenKirpi.]

99:00:00 is the best

[@rdy4trvl]

When I scan with Advanced IP Scanner I see 13 alive, 0 dead 241 unknown (all 192.168.0.xxx). However, when I use the command prompt I see 18 using 192.168.0.xxx what's the difference?