Supercharger Removal for 2015 Sea-Doo RXP-X 260
Vložit
- čas přidán 7. 09. 2024
- In this video, we go through the steps for removing your supercharger from an RXP-X 260. This is the same process from 2012-2016. Once removed, you can send it in to our Supercharger Rebuild Service @ PWC Muscle
www.pwcmuscle....
Nice job guys! 💪🏻
Hey thanks, Joe. What's the story with all the goop on the hull fitting for the drive shaft?
It's a late year 2015, and we've seen a number of 1-off solutions when they make changes to engines. Pretty sure that is what we are seeing here since it has the different style carbon seal.
I wish you guys had a video taking apart the supercharger I’m trying to make sure it’s an easy job. I need to change my impeller.
Do i need to reset the dashboard. Currently it saying service supercharger
What’s the going rate to have this done in your part of the country? If someone brought you the ski for you to do it start to finish?
Mine is almost all the way pulled out but the SC case is getting hung up on the drive shaft boot and ring …. I’ve been going at it for a while and can’t get it over the drive shaft ring any tips? 2015 RXT
Cuantos nm se apreta el tornillo del piñon de atras en donde van las arandelas ?
Tienes que patinar el piñon ?
Have been reading up on Supercharger removal for my 2010 Seadoo Wake Pro 215 (186 hrs)and some folks mention needle bearings falling all over the place and losing some when SC removed. I watched you guys just pull out the SC after 3 bolts removed and loosened SC up and did not see any indication or mention of care to not loose needle bearings (40). I have also read somewhere that you need to drain engine oil in order to remove SC. Is this true? To keep engine oil from running out of SC hole on PTO? Am mainly taking off SC to aid in drive shaft upgrade and easier access to fittings to swap to old style bearing carrier and shaft. I figure I will inspect SC externally while off. SC was rebuilt approximately 15 hours back from previous owner. If I find any inkling that the SC has issues, I will surely be sending it in to these guys for a rebuild. Thanks in advance for any tips..
Needle bearings can come out in chargers that had dual clutch failure. It is rare but has been known to happen. As for draining the oil, as long as the ski is relatively level you should not have an issue with excessive oil leaking if any at all. Hope this helps
@@darrylwilliams3720 Thanks very much for the prompt response
How much grease do we need to put on?
Hi nice video thank you!!! also quick question are you can rebuild 300 2017 supercharge?
They are a replacement item, which you can find on PWCMuscle.com
So I’m confused with my Jetski I have a 2017 RXP 300x top speed is at 75 and a lot of people are telling me that I should be going a lot faster with everything I have Install the only thing I have not done is any tuning at all. Also, after adding the speed delete from Riva I didn’t see any difference either it felt like it didn't even work, because when I turned it off and turned it back on, it still did not start back up in sport mode. Like people claim and the ski I purchase off of someone already had most of the mods on here the JetSki runs perfectly fine. Oil level is perfectly right in the middle. Yesterday I checked inside the intercooler there was no oil in there. It was perfectly dry. I replace a supercharger impeller, so I’m just lost for words maybe tuning might get it where it needs to be any advice or opinion to help me out here
Installed
Riva air intake, Riva ribbon delete, Riva I/C hoses with tial BOV, riva rear exhaust and riva speed delete ,Fizzle Z135 Supercharger Impeller, Solas Impeller SXX-CD-13/18 .
If your in the US there speed restrictions
What kind of lube/grease do you recommend on the charger shaft before reinstalling??
Any marine grease will work. It's just to prevent tearing the o-rings and help stop oil from getting past them
What’s the cost of your service ?
Whats the turnaround time if I send mine in to rebuild ? Also what's recommended is it 200 hours ?
I'd definitely not wait 200 hours. Turnaround time is 72 hours unless you select Expedited which bumps you to the front of the line
What’s the size torx to remove the bottom and side bolt off the supercharger??
E8 external torx
How does the coolant reservoir come off? Almost thinking this power cooler from riva isn’t worth the hassle! Might just keep my short 90 intake from jp racing. Does it make that much of a performance gain? I’m running a stage 3 plus
Jp ski’s hit 90mph with there intakes
@@bakerelectricextreme7979 Yeah, it does make a difference but will be the first to admit the install is a big pain.
O tiene que quedar duro
Hi, I’m looking for a turbo kit for my 2022 seadoo spark trixx, I see you have one on your website. I have a few questions on what else I will need to install to fit this kit in my ski. My ski is brand new , zero hours bone stock. Please message me🇨🇦😁
Definitely something to discuss over email, but we sell them regularly! Shoot us a message and we'll discuss what you'd want to do to move forward
@@Pwcmuscle
What’s your email
@@bakerelectricextreme7979 sales AT pwcmuscle.com
Hey, that’s my turd. I need a commission for this shit!
Installation is just the opposite as the installation process???? Lol
I trip on my words like cracks in the sidewalk lol