It’s because he put the fuel bowl back on wrong. Take the bowl off, rotate it so the drain plug is 45 degrees clock wise from where it is shown in the video. So the dean plug essentially facing the center of the rear tire. The bowl is shaped so the float can travel up and down and upon inspection I realized the bowl needs to be on so the float can operate unobstructed.
What ? CUng? I’m telling you the bowl is on wrong this guy in the video put the carb bowl on incorrectly. You should definitely remove the jet and clean that out
I have a second hand MM B80. There are a couple of missing springs on the throttle linkage. Can the carb be replaced with a pz19 slide carb and avoid piecing the throttle linkage back together?
Great video. Got mine back running after watching. I drained all the old, bad gas out too. The gas had gotten bad. I suggest sta-bil fuel additive always in smaller engines. I didn't do that before but am using the fuel stabilizer now.
I just got one of these bikes and it's missing some things. The spring and rod on the carb to the governor. The carb gasket is broken Missing a bolt for the air box. So far that's all I can see without knowing what it looked like originally. Are these parts still available?
I have a question, I've done everything you have showed. Gas filter, cleaned the carb, greased the clutch, changed oil & changed the spark plug. The issue I'm having is the engine will start and run great when it's in the start position, but when I switch it to run it will continue to die out. Any ideas?
@@beardedjalapeno5263 I got it running,but it only runs when the choke is on. When I put it on run it dies out. I let the kids ride it like that for a couple of week then I put it up. I'm going to replace the carb with a new one.
the muffler is under the cage on left side of motor if u want to eliminate it there's a flange where the uffler connects us can weld a straight pipe to
Pull the spark plug and pull a couple times. Might be vapor locked. Oil or gas got on top and doesn't let it u pull. With the spark plug out it should shoot everything out if u pull the starter rope a couple times.
When you say keeper I think you mean the main jet. That should also be clean very important. Really any passage should be cleaned and blown out with compressed air. That’s one of the most common issues due to buildup in the small holes.
I tried unscrewing the keeper from the carb with a flat head screw driver and it completely disintegrated. Now I've got small chunks of it stuck in that hole. 😐
WOW!!!! It's not a "keeper" its a jet. That's the part you should clean with carburetor cleaner, soak it overnight.. then blow through it with compressed air. that's the part that clogs. If that doesn't work just change it with a whole carb.
This is been a big help since I actually was getting my mini bike out of storage and cleaning it up since everything was pretty bad. The only thing I need is a brand new chain and I have no knowledge on where to get one specifically for this exact bike even though it's technically Motovox brand what is practically the same exact like. Is there any possible way I can order a chain online from you guys since the original chain has a broken link. Please and thank you!
@@JoseLopez-bt7zp wow I completely forgot about commenting on this but yeah I've been buying from gopowersports for a while now since this comment was made, and unfortunately coincidentally a year later, I'm ordering yet another chain specifically a Performance Racing chain because the basic ones keep breaking. This chain will be chain number 3**
Worst carburetor cleaning video I have ever watched. The keeper is a main jet and has a hole in it that you need to stick a wire through if your carburetor is dirty. Did not even mention the pilot jet which is what you need to clean if your bike won’t stay running at idle without the choke on. If you have a bike that’s been sitting for a while If you follow this guy steps it still will not be running when you finish lol.
I was able to get my engine running thanks to you! Thanks! Having a blast with it now.
I did a shot every time he said "go ahead" and woke up beside the mini bike. It still wouldn't start...
It’s because he put the fuel bowl back on wrong. Take the bowl off, rotate it so the drain plug is 45 degrees clock wise from where it is shown in the video. So the dean plug essentially facing the center of the rear tire. The bowl is shaped so the float can travel up and down and upon inspection I realized the bowl needs to be on so the float can operate unobstructed.
And my man didn’t even actually start the bike ! How do we know t runs ! I’ll bet you a years salary it won’t run that way
is the keeper has tobe plugged with some kind of cung in it?
What ? CUng? I’m telling you the bowl is on wrong this guy in the video put the carb bowl on incorrectly. You should definitely remove the jet and clean that out
Great work on teaching us! Really well done. Thank you!!!
What do I do if I lost the rod to the carburetor that controls throttle
Bobby pin works great
What about the spring??
I have a second hand MM B80. There are a couple of missing springs on the throttle linkage. Can the carb be replaced with a pz19 slide carb and avoid piecing the throttle linkage back together?
Help me out. Mine will crank only when I’m holding the accelerator and I can drive it a round. Do you know what the problem.??? Thanks
Great video. Got mine back running after watching. I drained all the old, bad gas out too. The gas had gotten bad. I suggest sta-bil fuel additive always in smaller engines. I didn't do that before but am using the fuel stabilizer now.
I just got one of these bikes and it's missing some things. The spring and rod on the carb to the governor. The carb gasket is broken Missing a bolt for the air box. So far that's all I can see without knowing what it looked like originally.
Are these parts still available?
I have a question, I've done everything you have showed. Gas filter, cleaned the carb, greased the clutch, changed oil & changed the spark plug. The issue I'm having is the engine will start and run great when it's in the start position, but when I switch it to run it will continue to die out. Any ideas?
Buy a new bike I had the same problem
Did you ever get it running??? I'm going through this now
@@beardedjalapeno5263 I got it running,but it only runs when the choke is on. When I put it on run it dies out. I let the kids ride it like that for a couple of week then I put it up. I'm going to replace the carb with a new one.
@@beardedjalapeno5263 if that doesn't work I was told harbor freight has a motor that will slide right in there.
@@JoseLopez-bt7zp I'm going to check it out. Appreciate it
Can you do a brake pad change I took mine off my kids to change them and now I can't get it back together. Please help.
thanks for sharing, got my bike back up and running with this.
Monster moto I did all of this and it will still not stay running what can be causing that
Didn't help me
the muffler is under the cage on left side of motor if u want to eliminate it there's a flange where the uffler connects us can weld a straight pipe to
What symptoms is the bike giving to where the carb needs to be cleaned..?
I’m about 2 years too late...but he says that at the beginning of the video
I hope this helps this 2 year old problem lmao
My pin didn't "just fall out"
After pulling out the little keeper key
What do I do
Dose the gas tank have to be empty
Did you not have the bowl on the wrong way and put it back on the wrong way ? Sure looks like it
What do you do if your pull start is locked and won't let u pull the pull start?
Pull the spark plug and pull a couple times. Might be vapor locked. Oil or gas got on top and doesn't let it u pull. With the spark plug out it should shoot everything out if u pull the starter rope a couple times.
Did this. Runs for a few secs then turns off....any idea?
@retro gaming time with joe it was the carb. Just picked up a new for 12$ on Amazon. Replace it and it fired right up.
@retro gaming time with joe it was over nighted. Also got led
@@beardedjalapeno5263 can you give me a link to the carb you bought?
@@williamhamilton9353 AUTOKAY Carburetor for MBX10 MBX11 79cc 97cc Carb Monster Moto MM-B80 80cc Mini Pit Bike Carb
Amazon
@@williamhamilton9353 just amazon. Still riding strong....
Mine is stalling and then ittl go then stutter then die.. and theres alot of dirt in the gas tank...
Anyone know the standard jet size this carb has? I'm at 7500 ft and need a smaller one.
They have a higher elevation jet on the website
When you say keeper I think you mean the main jet. That should also be clean very important. Really any passage should be cleaned and blown out with compressed air. That’s one of the most common issues due to buildup in the small holes.
the keeper that hold the jet streem has some chunks! is that need it to be like that or it needs to be cleand out also?
Thanks
Good video !
Can I order gaskets from your guys?
How do you run the throttle?
What kind of spray did you use
Kirk Preston it’s been 4 years and we still don’t know
@@Josh-zy3lq8 years
I tried unscrewing the keeper from the carb with a flat head screw driver and it completely disintegrated. Now I've got small chunks of it stuck in that hole. 😐
Christian Hill.same thing happened to me
same
Thanks for the help
WOW!!!! It's not a "keeper" its a jet. That's the part you should clean with carburetor cleaner, soak it overnight.. then blow through it with compressed air. that's the part that clogs. If that doesn't work just change it with a whole carb.
Do I need to clean the carb if the bike is brand new ?
No
6:26
were and is there a muffler on the monster
Yes it’s o the side it’s the black box that’s all bard up in a cage
What if we dont own carb cleaner
Go buy some. You also may need to buy some wrenches and a screw driver.
How can I order a gasket and a carburetor
Go to their website
What is that rod and spring called I'm lost mine and need to buy another
It’s been 3 years did you figure out what the spring was called!!!!!!!
How do I call yall to get a filter
I get all of my parts from www.gopowersports.com. it's a very fast turnaround time.
@Ayden okrem hum..... Buy some?
is monster moto the new name for motovox
Trevor Aureliano no they are different companies
Oh I was about to say because they seem very similar I have pretty much the same exact bike
Motovox went out of business and monster moto and a bunch of other companies stole the design since the patent still didnt come into act.
Sorry to say but this bike is junk I had it for one week and now won't start
Gregory Galvez ive had it for 7 years...
Gregory Galvez yo then do a predator swap man the old engine is not as good as a predator
Ive had it 2 years still starts
This is been a big help since I actually was getting my mini bike out of storage and cleaning it up since everything was pretty bad. The only thing I need is a brand new chain and I have no knowledge on where to get one specifically for this exact bike even though it's technically Motovox brand what is practically the same exact like. Is there any possible way I can order a chain online from you guys since the original chain has a broken link. Please and thank you!
www.gopowersports.com
They have almost any part you need. They ship very quickly. Shipping is a bit pricey, but parts are quality.
@@JoseLopez-bt7zp wow I completely forgot about commenting on this but yeah I've been buying from gopowersports for a while now since this comment was made, and unfortunately coincidentally a year later, I'm ordering yet another chain specifically a Performance Racing chain because the basic ones keep breaking. This chain will be chain number 3**
ITS A JOKE IT'S ONLY 90 DAY WARRANTY AND I HAVE 5 MONTHS AND DOESN'T WORK I SHOULD KNOW OR READ BEFORE BUY
Just get a predator engine after warranty has passed you'll be lot bettet off
snattle rake predator bolt right on?
Predator motor bolts right on? No mods?
Travis Cadello no mods but i sold it
Thank you for explaining how to change the carburetor, that was a lot of help.can you please send me a carburetor and a gasket for my monster moto.
Great video can you explain to me why these engines are pieces of shit?
I got a bike form you and it is spiting out oli and i new
Worst carburetor cleaning video I have ever watched. The keeper is a main jet and has a hole in it that you need to stick a wire through if your carburetor is dirty. Did not even mention the pilot jet which is what you need to clean if your bike won’t stay running at idle without the choke on. If you have a bike that’s been sitting for a while If you follow this guy steps it still will not be running when you finish lol.
OUT OF BUSSINESS
WHAT!
Thanks