Ford Escape: Customer Threw In The Towel - No Start, No Crank
Vložit
- čas přidán 26. 11. 2022
- In this video I have a look at a customers 2013 Ford Escape with the big 2.0 that has a customer concern of a no start, no crank. He gave it the old college try but could not come up with the answer. Let's have a look.
-Enjoy!
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
CHECK OUT OUR "SMA SWAG" STORE! Go on Teespring and get your very own SMA merch!
teespring.com/stores/the-sma-...
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/SouthMainAuto
The South Main Auto Amazon Store:
www.amazon.com/shop/southmain...
AES Wave Automotive Diagnostic Tools: www.aeswave.com/cart.php?m=af...
Thank you for all the continuing support!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained. - Auta a dopravní prostředky
It's actually impressive that the guy figured out how to start it with jumper wire.
I think "the guy" is another auto tech that reached the end of his troubleshooting ability for this problem.
@@michaelslattery2121 😆
This time the customer tip was handy. Could have gone either way
I know there was a time when I could get all your cable-tv pay-per-view channels this way. But I could never get a car to run with anything like this.
Who is the "guy"?
Give the owner some applause for figuring out a jumper wire started it.
Yup. And for pointing toward the BCM as well.. He just had one more step, and he would have had it!
The owner must be a South Main Auto suscriber.
@@garysgarage3669 If not a subscriber I'm sure he is now! lol
But he could've also fried something else, he got lucky. and helped Eric a little also.
Yes and start it without bricking the ECM or BCM.
Nice diagnosis & repair! Congratulations on 750K subscribers. You have helped me get thru all my days fighting my cancer by enjoying your videos. I wasn't able to work on cars for the last 3 years but it was like I was watching you. I am cancer free now thanks to stem cells from my brother & the medical staff at the Bone Marrow Transplant Unit & God! Hopefully next year I'll be back to fishing & working on cars again! Thanks again for your videos!!
Hang in there. 👍 I get my MRI/Ultrasound Fusion Biopsy prostate cancer results in 45 minutes. I have PC, and I'm in Active Monitoring. 2nd time for this one. 2 MRIs and 3 needle biopsies overall so far. Piece of cake, takes 30 minutes in a doctor's office, but the anticipation is horrible. Took 9 months to diagnose in Feb of 2021 because biopsies during COVID were Elective Procedures. Luckily PC is a very slow cancer and ideally you die of something else first.
@@dlewis9760 I'm doing better every day. Prayers for you.
@@haywardsautomotive6156 Just got back. Doctor: "How you doing?" Depends. How's my #s? "No change". Then I'm doing great. Maybe another MRI in a year or so and maybe another MRI/Ultrasound Fusion Biopsy in 3-5 years if the PSA #s don't go crazy. The cancer that's there is still there, but hasn't spread. You don't realize how much tension you are under until after. I want to go to bed and it's not 5 PM yet.
I remember Eric when I was like his 1500th subscriber or something. I've learned a huge amount from him, very few repairs or diagnoses I won't tackle now.
@@dlewis9760 Good luck with the PC. I had a mere prostate infection once and my doctor and I talked about PC and I remember him telling me that a lot of people die WITH it rather than FROM it because it spreads so slowly.
These electrical problem videos are like watching a really good suspense movie.
Great video..as always. I, and I suspect many others, appreciate you've taken several hours of research and work and netted the actual video down to 35 minutes. In 35 minutes, you covered all of the essential learnings, methods, and key points required to make a worthwhile video.
Eric; How I wish I could find a mechanic that I can "TRUST", AND, who is as Honest and logical, such as yourself. It has been my experience, that you are a rarity... Sadly, you are a Gazillion Miles from me... My hopes for your continued success!
Your analytical skills and methods helped me in fixing my own vehicle and solved why I couldn't fix an issue 40 years ago also. I went over what I learned this time and it dawned on me what the problem was then. So by watching how you analyze and solve problems, has helped myself and an unknown number of others. My hat off to you sir!
Eric, please go into teaching future mechanics. Your analytical approach is an excellent example towards problem solving
Ditto!!!
Could you tell us the vehicle and the issue you faced?
I'm an electronics tech, not a mechanic, but your electronics skills are incredibly good. Well done Mr. O.
Eric, you are a better man than me....I usually pass on electrical and stick to all the bearings, brakes, suspension, frames etc....diagnostics is an art and I am not well versed in that so I let the professionals do it....i can find a squeak, rattle and bang under your vehicle but as soon as the money light goes on, my brain goes off...LOL
A man's gotta know his limits!
@@SouthMainAuto I do and have absolutely no problem saying, "I don't know"
@@brianbanks3044 electrical problems can be an absolute nightmare. I, myself, have been down the rabbit hole a time or 2
@@brianbanks3044 I vastly prefer a man who says "I don't know" than one who thinks he knows but really doesn't!
Electrical issues like this are an absolute blast for me. I have spent days splitting harnesses to find a broken or pinched wire. Makes it even better if somebody was already there and could not figure it out.
my 26yrs in transport refrigeration repair taught me to be very thorough when fault finding, I can honestly say in all those year I had only diagnosed 2 faulty microprocessors, it was nearly always connection or broken/bad wiring. Good job Eric, thoroughly enjoy your diagnostic prowess.
I'll bet 99% of any other shop would have thrown a BCM in that puppy, considering everything pointed there.......Eric O to the rescue, as usual. Great job, sir!
Eric's content is probably the best educational content available and presented very well . I have attended almost all forms of training available from a 2 year college course to GM training back when it was a live in person classroom with Instructors . Eric and his explanations are much better ! Eric makes the diagnosis almost hands on for the viewer .
The classroom problems are generally structured to go with the course. Eric's problems are real world and constantly varying. Being able to problem solve is an aptitude. Couple that aptitude with education, experience, and an honest work ethic along with being gracious enough to share that talent, and you end up with Eric!
@@terrygaddy7768 oh okay . 99% of the training I attended was theory of operation and the fundamentals of concerns , causes and corrections rather than what you stated . More of the thought process needed to repair correctly which Eric does very well and explains it as he does so ...
I watch eric da mechanic ( car detective ) in my spare time and he has given me the confidence i need to at least investigate my automotive issues before i bring to a garage for repairs….
Yes I have done five year’s at the College of Eric’s and Mrs O’s .
Eric O , is getting a lot of shout outs in the rainman ray channel. It's amazing how differently things get done in sunny Florida!!
Nice work Eric O. I love the method you use, the restraint against going with your gut, and the simple do the right thing mentality. Thank you yet again for being the man you are! Your family as well as Avoca are blessed to have you!
Not only do the right thing, if he or anyone called it a bcm, it wouldn't have made a difference and the car would still be broken. It's almost never a module.
i feel the customer's pain, can imagine how much time he spent trying to figure it ou- we've all been there.
SMA shows the value of intelligent experience, for the win.
That was quite the ride Mr O! The mystery, the misdirection, the intrigue, the logic, the resolution, and the freebie! I thing I need to go have a smoke now.
I freaking LOVE how you talk about the video looking cohesive “a couple clicks on the computer and boom we’re done!” God my entire life is the background work in which nobody appreciates. I admire your dedication to finding the correct answer and I learn so much from your troubleshooting ability. I don’t have any of the vehicles you work on, but the way you go about things is always fun to watch.
Three quaters of a million subs my man! Look at you go! (P.S. Bring back the big nasty and brake clean sound effects lol)
Also drives around town with the old music and the video running at 1.5 speed.
I second the motion!
I'm REALLY disappointed when Eric pulls out the breakclean and the sound effects are not there.........Man, what a letdown!
But still......... it must take some extra time to put them in. Maybe time Eric doesn't have to spare. I would assume that he is a very busy man.
You are becoming my favourite Electrical circuit Guy :) Number one is Information, Number Two is Knowing how to use that information. Great find from Process an proper testing. All the best from Australia
These really remind me of my time in the Navy. I was an FC (Fire Controlman) and some faults would drive us nuts. Most solutions would be found either by trying to explain it to someone on the smoke deck or you would bolt up out of a dead sleep with the answer. I guess the take away from that is don't let a fault drive you nuts, take a break and let the brain static die down.
Same thing for me when programming and faced with a problem. Sometimes you need to walk away and let your brain do some thinking while resting.
Thats the fact Jack.
Some faults are best revisited after a breather
our subconcious is a wonderful thing.
Really appreciative of your discipline to confirming that you really know what you think you know. You can do a lot of “unnecessary” triple checks before you exceed the wasted time and unnecessary frustration that comes from believing something that isn’t true. Plus it is a super effective way for us to learn the purpose and outcomes of your tests. Love your diagnosis videos!
It's very generous of you to let us inside your head the way you do. I really appreciate it as do a lot of other people I'm sure.
Keep up. The good work.
Improving the world in your own way. One video at a time.
A few months ago I wouldn’t have been able to follow. But since then until now, it’s worlds apart. I had a cooling fan issue that I was able to solve thanks to this channel along with a few others. 🙌
If you can do it ...... I can watch you do it! I love your videos. This one is an example of how a very small problem with a cut wire can shut down a vehicle. Who would of thought? Thanks for your videos. They are incredible.
Too bad most techs just throw parts at a car , it seems like very few can even follow a wiring diagram. Great job as always
you never cease to amaze me, its like you can almost smell those broker wires, great job!
You would make on hell of a teacher. You make it look so easy, so logical.
Once again you followed the knowns and discovered the unknown. Your methodology is truly a sight to behold.
I love your videos. As an ASE Master L1 Certified Technician who's been in the business on and off for over 30 years and worked at several dealerships I have to say hats off to you. I learn something from almost every one of your videos I watch. Please keep doing what you are doing, your efforts are appreciated!
Thanks for sharing!! This helps build confidence and skills to keep asking questions until fixed. Can only imagine how many cars I see just sitting/rotting are one wire away from running… Great work!!!
You are the GOAT! Glad I finally found a REAL mechanic on CZcams. I’m a little older, so my opinion might be swayed in your favor since I remember when auto mechanics actually DIAGNOSED issues with a vehicle instead of throwing new parts at it until it’s fixed. PLEASE keep doing what you do, and I’ll make sure to spread the word about your channel. Again, THANK YOU SIR!!!
Fantastic job! I worked for 30 years on complex multifunction copiers with even more wires, most often with the all the same colored wires…… But excellent work. One tiny lil wire that got crushed / cut- can totally sink the ship. Very impressed and reminded me of my old days before I retired. You are smarter than the average bear!
Another top job Eric, good methodical approach. Wiring is a rats nest in most cars I think that's why a lot of folks don't want to touch it. You have patience and a good logic. 👍
You would think in 2022 most new cars would have less wiring in them instead of more then the cars of 50-60 years ago!!!
In the 1950s some cars had 8 fuses. Now there room for over 100 in two or three different fuse panels. Modern cars are nothing but a rolling wire chase.
Wires get that way cause owners think theyccan fix it then when they cant take it in some there mistake can be fixed then fix the original problem.
I like your methodical train of thought on repairing all of these electrical issues in your videos.
Very interesting video! I'm impressed as usual. It's beyond me how 18,000+ people can watch an amazing trouble shooting as we saw here and NOT give the video a thumbs up.
Watching Eric's videos makes me feel like early man when the wise person in our village showed us the magic of fire. I'm awestruck.
Hey Eric! Glad that you were able to find and fix the cause, that would try anyone's patience. This is one where experience does help in figuring out the cause of the issue. I do remember that episode that you were fixing the head lights inop issue, same kind of cause, and same area of the wiring harness. I've got something similar hanging on my hoist right now (Sunday 11/27/22), a 2011 Durango, cranks but doesn't start. Checked the dtcs, (there were numerous dtcs, and the battery was nearly dead) noticed a dtc for the fuel pump control circuit high, and three dtcs for the fuel level sensors low and high. Checked the relay, got both powers there at the relay. So I tried some starting fluid in the throttle body, starts and runs on the starter fluid. It was written in the customer complaint that 2 fuel pumps have been put in at other shops. So I decided to check the wiring. Found that the wiring harness is pinched between the tank and the body. Going to be asking for additional time tomorrow morning to drop the driveshaft, exhaust, and the tank to access and repair the harness. Pissed me off that people don't double check their work to prevent this kind of issue. Watching your videos inspires me to be more confident in my electrical work. Seeing what you do gives me ideas to diag these cars. Electrical is getting to be a bigger part of auto repairs than it has been in the past.
Two fuel pumps put in after the wires were pinched which caused the first pump not to run? Am I missing something?!
We don’t know if the wires were pinched prior to fitting replacement pumps…think you’re jumping to conclusions!!!
Poor connections have been haunting cars for decades though. My parents' late-80s very basic Japanese van started randomly cutting out after longer drives when it was a little under ten years old. Several mechanics couldn't find an issue over the course of almost a year until one finally figured out it was an intermittent plug on a wiring harness that fed, among other things, the fuel shutoff solenoid. The harness was tied to a brake hardline somewhere around the engine so there was definitely a lot of vibration going on. Simply cutting the cable ties holding the plug to the pipe fixed the problem for a while until it started raining and water splashing up made the connection bad again. The next morning a garage bypassed the wire for the solenoid and that got us home, some 800 km. In the end my parents got a free wiring harness replacement because their garage had missed the real problem the whole time and was a bit embarassed.
Granted, it did help that the problem suddenly went from "only occurring after several hours of motorway driving" to "rendering the car almost useless after half an hour" making the fault easier to observe. Several mechanics had rightfully concluded it was a no fuel condition but never made the connection it might be an electrical issue rather than a clogged fuel filter or something along those lines.
@@dans_Learning_Curve It is unknown when the wiring got pinched. The pumps were put in at other shop(s). It was towed in, and I don't have the full story. Regardless, the pinched wiring is saying a lot about previous techs. Imo, it means that they did not double check their work. I double check, because i've been bitten a long time ago by not double checking my work.
Definitely one of best mechanic I’ve ever seen. People lucky to have you in there town. Good job.
Definitely the correct approach in this situation. Normally I try to ignore whatever the previous shop or customer did and start from scratch, but considering it ran with the jumper wire it clearly makes it a bad BCM, relay, or open circuit.
You’re the man!!!! Not just any shop or person for that matter could figure out a case study like this one. Nice job! I learn something new from everyone of your videos..
Love the way you analysis the entire system and not just the problem. We need a lot more like you Honest always doing what is right for the customer. Thanks
I'm learning as you go Eric.
I watch your videos because I am amazed by your diagnostic abilities, esp. with electronics and wiring. Your logical, systematic approach is outstanding! When I look at newer car wiring, I usually feel defeated before I start. But watching your channel proves it can be done. Keep it up!
I really appreciate that you approach each problem with an open mind, even if the initial information points down a particular path. Troubleshooting is always a matter of gathering the available data, no matter the source, creating an hypothesis, and testing. Nice!
Your skill, knowledge, and determination go unmatched by anyone Eric.
2:43 "and some dingers going off *door bell*" LOL Timing was PER-FECT! 😆
I noticed that too 😂
Kudos to the customer for diagnosing down to relay off the BCM, AND not just swapping the "mystery box" (BCM) like many would! I also enjoy following along with Eric, and the thought process. Dood!
If Eric O can do it, trust me, doesn't mean I can do it!🙄🤔. Holy cow, that was pure technician know how, 99% of Ford dealership mechanics couldn't have fixed this. Personally I would have torched it, I don't have the patience but I do ADMIRE those like Eric that do. Hello Mrs. O too, I am sure she helped somehow someway.
I would imagine he would tell you just having someone running interference in the office is priceless.
I love all your videos, but, as a retired electronic technician, I enjoy watching how you troubleshoot an electronic problem the best. I have to say, your technique is spot on.
I was always at a bit of a loss as to how to explain to a customer exactly why repairing a small wire, (or whatever it was), cost them so much.
30:00
I am a lineman for an ISP ... You would be shocked how much copper breaks INSIDE the jacket and the jacket holds together.
Trouble shooting an open or break in a copper line can be fun especially when the jacket maintains its shape.
Great work that brings me back to my residential security repair career. There's nothing like that "ahah" moment after scratching your head for hours.
I'm glad there are Great mechanics like Eric that know they can't work on everyone's vehicles...but yet are willing to share their experience with us!
I am always amazed at your troubleshooting skills.
Been a mechanic, I appreciate you educating the public on what it takes to diagnose a fault. I use to enjoy diagnose until autozone came out with free scan and I found myself spending more time explaining cost then actually diagnosing.
I know talking all of us through the process took a while and editing it. Thank you Eric and family. It is helping many and those of The Kingdom.
Owner sure did his part leading you down the right path in the beginning. GREAT Job by both parties.
I'm continually amazed at your attention to detail when troubleshooting issues along with your overall ability and skills to make the repair itself. I sure wish my area had someone as competent and professional as you are. You probably get that comment or something similar all of the time. Wishing you all of the continued success in the world as it is people out there like you that certainly deserve it.
Hi Eric O During the last 5 years of working on vehicles they were nice enough to drop the electrical problems on me. I understand they did not want to tie up the younger guys time with unimportant stuff. I never liked to follow up other mechanics because they may have created additional problems. Working on the one circuit, one wire problems was also no fun. Here is what I did if it can be of any help to you or others out there. Take your long "YO YO" test leads and bridge the wire end to end to jump the broken circuit. If it starts working then you are looking in the right place. Now take your jumper leads and cut the wire "mid way" and again bridge the circuit. This method helped cut a lot of time off locating the area of the broken wire. I worked on a lot of abs speed circuits, suspension controls and circuits, trailer brakes and control circuits. The stuff that was covered with mud and rust. It looked like you found the stretchy "rubber band" broken circuit. Where the plastic coating was intact but the copper wire was broken inside. Heat shrink butt connectors are fine by me. I always gave them a tug test, if they passed I am good to go! Great Job, Happy Thanksgiving.
I have been an automotive technician for over 40 years I love to watch you work rather than myself lol do a good job just like I would do.
Hi. First time watching your video. I am an retired ASE technician and wrecked my head many times with problems like this with less modern diagnostic tools. Tech One and my Fluke was the in thing then. Common sense and past experience kicked in after a few years dealing with Cadillacs and GM. Fords were always tricky because they had a thing with hitting around the bush when it came to diagnostics. Maybe I'm wrong but that was my experience. Well after 30 years in the industry and being a woman I enjoyed the respect given to me by other technicians and I think you are a brillant one. Respect to you! I enjoyed the video. Good job. Now, the owner wasn't stupid I tell you!
These videos are the ones I really love. I love watching Mr O doing a diagnostic on a electric problem. Great job and video Mr O 😊😊😊😊
I think they actually pay people to make car technology just short of impossible to work with. I miss the good old days when all it took was power to the coil. Great T/S session Mr O
I love these wiring diagnostic videos! More please?
I would have difficulty given up also you
Mr. O” are a genius on wire brakes it’s amazing your talent for rooting out green corrosion in side cables.
Eric , you are the overlord of wiring!
These are my favorite videos I always love to chase broke wires. But nowadays I would never even think about doing what you do with all these electronics. Thanks for the knowledge.
Impressive that you take the time to investigate every option instead of just replacing every module, not many mechanics would do what you do !
This guy is a great mechanic/auto technician. I have a 2014 Escape and it's a quirky duck at best. Lots of electrical and electronic issues engine issues and transmission issues. This particular electrical problem probably is next to impossible for the shade tree mechanic to fix. Grareful for these experienced guys with access to and know how to use diagnostic equipment. 👍👍
What do you expect from a vehicle named after o. J. Simpson
This goes to show how important a thorough visual inspection is. Good find Eric.
Excellent troubleshooting. I do that all day on different equipment. Cool to see someone else doing it.
You never fail to enlighten me with you diag skills brother.
So love this sort of video. It's what I do most days but I learn off you way you do the figuring out. Love it
Nice fix. Have to admit I wouldn’t have been able to do that. Such electrical trouble shooting skills are rare. Your mind works in mysterious ways! 🤪 Enjoy your channel immensely.
I love the thorough troubleshooting and diagnostics when you chase down electrical issues. These are my favorite type of videos on your channel. Well done.
nicely done eric, i learned a lot from you. few weeks ago i did a no crank forklift where the owner tried on for a year by different mecanics. the jump wired every fuse🙄. the problem was a broken off pin in the power feed for the ecu in the engine compartment.
thnx again for educating us in such a simple way✌
i have been working on cars for 40 years evertime I watch one of your Videos I learn something
Glad to see that the Rear Defrost Switch is not depressed.
Once again never a dull moment and always informative. Diagnostic skills on another level.
Your research hours were well spent, from my point if view you were very on the ball and stuck with your game plan. 👍
I really appreciate you letting us know how much time it takes you to do a repair. This way we don’t feel like idiots when we can’t figure something out in 1 hour. I really like your videos. Keep making them.
Eric, this is one of my favorites!!! I feel for this customer, You can smell the frustration. You make it look easy but..... "The more I practice , the luckier I get" A true Professional. Thank You for all the content You push out, I watch them all.
This is the stuff I absolutely LOVE tracking down on my own! It's hard to figure out and trace down, but you learn so much through the whole process and mind-set in doing the job... It makes you feel like a true professional when you test things; figure out what works and doesn't, and then use your mind to trace down where the issue lies after you've mentally figured it out in your head already and verified it all along the whole process...
And then the BINGO moment when you suddenly spot the issue, and are like... Yep, it's a 30 second fix and a 5-cent part (adheasived lined butt connector), but it's a several hour experience tracking down that one little broken wire!
Been there, done that! And I tell you, I still get enjoyment each time I run across a job like that one!... The main key though, is like you said, access to the wiring diagrams & connector pin-outs and general description of how the circuits are supposed to work... Without all that, you're basically dead in the water and VERY VERY difficult to figure out that info on your own (difficult, but not impossible as I've unfortunately had to figure them out on my own a few times without access to the info I needed like wiring diagrams and schematics)...
As Doc Brown said in Back to the Future 3 (when inspecting the schematic for the time circuits that got fried by the lighting strike) "Unbelievable that something so small could cause such a big problem!"...
No wonder that circuit failed, it says it was "Made in Japan" hahahahaha
I absolutely love some systematic fault finding, both doing it myself and watching others! Some people immediately jump on a wild goose chase when they see a fault and I always tell everyone to take a deep breath, step back and think clearly what the symptoms could mean and what's a plausible cause.
I WOULD TAKE JAPANESE OVER CHINESE
@@rockyj2008 That part was a Joke from Back to the Future 3 where the time circuit control micro-chip shorted out during the unexpected lightning strike in the 2nd movie... The reason they added that "made in Japan" joke was because they had literally just won the war when they dropped the atomic bombs on Japan; and after that Japan was recovering from the war and were known for not being able to produce high-quality stuff after the war till things recovered lol
@@jeepjoe1996 👍
Some absolutely amazing work tracing this down. Thank you for going over the whole process and explaining the methodology as always, really helps get an idea for how these control circuits work. Lots of people would have just put a BCM in and then been very, very upset when it still didn't start....
Great video that shows the value of a competent and honest technician. It also shows problems can't always be properly diagnosed by simply pulling fault codes. As a technician it has always been interesting how many people will throw hundreds or even thousands of dollars worth of parts at a car because they won't pay someone who knows what they are doing to diagnose their problem. Over the years I have seen many cars come in that the customer wants a part replaced and doesn't want the problem diagnosed, only to have to pay for diagnosis after the part they wanted replaced didn't fix their problem.
Yet another example of how proper diagnosis leads to a cure without firing off the parts cannon. Thanks for another great video.
Great diagnosis by sticking to your principles Eric. You have got to be one of the luckiest guys re locating breaks in cables. It was interesting to hear how long it took with respect to the research side of things. I recall hearing Ivan & Raynman saying the same thing recently.
Watching this and Diagnose Dan's channel for years leads me to believe that when there are all those seemingly unconnected codes being set, the problem has always been a broken or melted wire. And I agree with those who say that 99% of Ford dealer "technicians" would have bailed on this. I think any dealer might have done the same. Well done, Eric O.
dealer would have sold him a BCM and then a harness
Probably 99% of all dealers no matter the make. Most arent trained in it.
@@kennethbode2017 you’re not lying. I just had a car where the Nissan dealership tried to sell them a $1000 TCM and their only problem was a speed sensor behind the starter that was left unplugged. In those instances I usually call those places and inform them of their misdiagnosis. Some get defensive and some seem grateful but I doubt any of them really care. I guess I hope that the service writer handling that ticket cares enough about the way it makes him look that he will try to get something done about it in their shop. I don’t want to get anyone in trouble but I would much rather our industry not look like crooks so much of the time due to incompetence.
Great tip from the owner to start you off. Being a prior new car tech for MOPAR/Fiat, AMC/JEEP, broken wires were the biggest culprit when electronics were starting big in the 70/80's. A lot of pinched wires under door rocker trim panels!
When it comes to finding bad wires and connections, you are the GOAT.
Interesting, and one that is a textbook example of being careful to not jump down the rabbit hole but to stick with one item and do your best to ignore everything else until you are satisfied with that one initial item. You, Ivan and Ray all tell us powers and grounds, and this, even though convoluted was still proof of that statement. Belated Happy Thanksgiving wishes to the O family!!
Just my opinion, I actually quit watching Ray because all to often he fires the parts cannon with out testing, and he guesses A LOT, again, without testing. I just feel he thinks he's better than he shows he is.
You and Ivan on the other hand are two top notch guys, along w Scanner Danner and of course Keith!
@@brianmason8400 he probably had to coverded ALOT of parts over time 😅
Nice work as always Mr. O! I always try to focus on one symptom at a time but the problem here was which symptom to follow. Great job! 👍🏻👍🏻
Wow, so lucky that was not back under the battery tray. Good job on the diagnosis.
You are the man Eric!! Whoever worked on that before you went clear down the trail,,but didn't get to the falls. He did real good!
We're never going to see a Ford Escape at SEMA, in 40 years.
As always Eric - very impressed with your troubleshooting skills and logic deductions. Way to help this guy out - saving hours of labor
Them weatherproof connectors are Gold!👑 and if used properly you'll never have an issue with that repair ever!
You got right on that one Eric. Ya didn’t let it send you off in several direction. Very logical approach
Great job, Eric! These jobs, though potentially tough, are great to come across coming from a diagnostics perspective. Very satisfying. Great diagnostic strategy and the kind of video I look forward to seeing.
Awesome diagnostic job, great video as always
These find the circuit issues and the smoke tests are my fav videos
Got to love when the customer does a bunch of diag before you get it Always helps a ton when the customer can give direction good video Eric O @South Main Auto Repair LLC