Wrong, wrong, wrong!!! When you cut out your tracing NEVER use a positive & NEVER pin it to the foam! Use an Exacto knife to to cut out a negative. Instead of cutting around the outside of the object, cut inside the negative (hole) you just cut out. Wire has a tendency to hang at corners or other places and cause problems. If you cut on the outside, every error shows. If you cut on the inside then if there is a problem it is in the area that is either thrown away or is underneath the object. And instead of using pins (too many problems to mention), use a light coating of spray adhesive to affix your pattern to the foam. Easy peasy! Happy cutting!!!
JM, i'm interested in that gadget too! I could really use something like that for projects but haven't found any on the retail front. Anyone got any info on it? TCM84?
How were you able to get the foam to cut within the edges of the foam? I want to do one for the console of my truck and car but don't want to see any cut lines going out to the edges. T.I.A.
The problem with this kind of setup, is with each pocket, you have to dismount the wire, exactly like that of a scroll saw, this video is not showing this. When you dismount the remount the wire, which is: load on load off, this will shorten the life of the wire which is under tremendous heat and stretching. In addition, you will have to wait for the wire to cool down before the dismount. Secondly the table foam cutter is never revealed as to show its function and advantages, so that the prospective buyer of the plans can make an intelligent decision.
1st, there is no other way to insert the wire in the middle of the foam without threading it. 2nd, I have used the same wire for over 100 projects, I can afford the $3 if I need to replace it. 3rd, when power is removed from the wire it cools within 2 to 3 seconds...I can wait.
Next time just flip the foam over and trace out a revered image with a fine point marker then cut and then flip the foam back over. Same results, 1/2 the time
Thank you very much. Now I know how to make my case.
I was more intrigued by the pencil holder for tracing the pattern!
Great vid thanks!
Very good, thank you
best video ive seen yet want to build one cant find the plans.....
Any tracing tips? I noticed you were using a guide or sorts to maintain a constant tracing angle. Thank you.
Wrong, wrong, wrong!!! When you cut out your tracing NEVER use a positive & NEVER pin it to the foam! Use an Exacto knife to to cut out a negative. Instead of cutting around the outside of the object, cut inside the negative (hole) you just cut out. Wire has a tendency to hang at corners or other places and cause problems. If you cut on the outside, every error shows. If you cut on the inside then if there is a problem it is in the area that is either thrown away or is underneath the object. And instead of using pins (too many problems to mention), use a light coating of spray adhesive to affix your pattern to the foam. Easy peasy! Happy cutting!!!
What's the background music? I like the song.
Using a shorter wire improves accuracy.
JM, i'm interested in that gadget too! I could really use something like that for projects but haven't found any on the retail front. Anyone got any info on it? TCM84?
How were you able to get the foam to cut within the edges of the foam? I want to do one for the console of my truck and car but don't want to see any cut lines going out to the edges. T.I.A.
+Kevin Beal I use a needle to get the wire through.
what sort of material are you using for your template?
Very nice video. Your pencil marking tool really caught my eye. Do you have any information on that?
Ditto. I would like to recreate it
what kind of foam is that?
btw that's sponge not eva.
how much yyou purchase foam
The problem with this kind of setup, is with each pocket, you have to dismount the wire, exactly like that of a scroll saw, this video is not showing this. When you dismount the remount the wire, which is: load on load off, this will shorten the life of the wire which is under tremendous heat and stretching. In addition, you will have to wait for the wire to cool down before the dismount.
Secondly the table foam cutter is never revealed as to show its function and advantages, so that the prospective buyer of the plans can make an intelligent decision.
1st, there is no other way to insert the wire in the middle of the foam without threading it. 2nd, I have used the same wire for over 100 projects, I can afford the $3 if I need to replace it. 3rd, when power is removed from the wire it cools within 2 to 3 seconds...I can wait.
You have only responded to one of the points I've made, can you address the others?
Actually, he responded to 3 of them.
Are you testing out how to comment on CZcams or are you reading the post? The second part (second paragraph) was conveniently not answered.
Next time just flip the foam over and trace out a revered image with a fine point marker then cut and then flip the foam back over. Same results, 1/2 the time
The music sucks...makes me want to set my ears on fire.
Perhaps you have been unware all this time but your computer actually has a volume button...give it a try sometime.