Husqvarna Rider, how to change the belts and remove the cutting deck
Vložit
- čas přidán 25. 08. 2022
- How to change the belts on Husqvarna Rider 13, 11 och 850. I also show how to remove the cutting deck and give some DIY tips on how to maintain the Husqvarna Rider.
Belt from engine to hydrostatic transmission:
531007572
Belt from engine to cutting deck:
531005016
Belt on the cutting deck:
531005022
I buy my parts from:
www.reservdelaronline.se
www.rembutiken.se
www.maskinklippet.se
www.briggsparts.se
Good luck with your belt change and thank you for watching! - Auta a dopravní prostředky
Mycket bra video som jag väntat på.Stort tack!
Kul att höra! Såg du att det finns en svensk version med?
You did a great job there showing us and make it look easy 🙂
Thank you! It is easy!
Thank you Nils. I have an R175 Rider (Australian model) and it looks pretty much the same. Very helpful video. :)
Glad I could help! However, I think your rider has a different deck, might be similar enough for this to still help.
@@NilsKall Not as similar as I thought at first but good enough! And your tip to inspect the deck before just replacing the belt was good advice. I found other issues.
Thank you! Good educational video
Glad you liked it!
Dziękuje 😊
Mam pytanie
Jaki inny agregat tnący pasuje do Rider 16?
"Thank you 😊
I have a question
What other cutting unit fits the Rider 16?"
Hi! This cutting deck doesn’t fit the Rider 16. Rider 16 came with rear 97, bio 103, combi 103 and perhaps 97 side discharge on some markets.
I really appreciate these videos. Really well done and useful. I have a Rider 155, the one with the pull-out pin on the left rear to disengage the clutch. Do you know which belt goes on the upper, and which on the lower pully, at mid-body?
Hi! Great to hear you like my Rider videos! The belt going forward towards the cutting deck is on the lower pulley of the center double pulley.
@@NilsKall Thanks for the help. Mine had come off somehow just as I was finishing up cutting the other day, and I didn't even notice (had to search for it in the yard when I later discovered it missing). I realized it was missing while installing new blades as the front belt slipped off the middle pulley also. Long story short, I put the front belt on top and, once finding the back belt, put it on the bottom. When I started the mower, the back belt was engaged enough to be moving even though I had the deck up. I hope this was because of me using the wrong pulleys...I'll find out today when I try to fix it ;)
@@brazzesr that could be the issue or perhaps you routed the rear belt on the wrong side of the tensioner pulley?
@@NilsKall It's on the inside of the tensioner, but tight enough with deck up to still drive the deck blades. Just for sanity, the middle belt isn't supposed to turn without the tensioner pressed on it, right, or is there a PT clutch in there I don't know about? I can't get the blades to disengage--driving me crazy ;)
@@brazzesr The tensioner is the ”pto” clutch in this system. There should be a belt guard behind the motor, they sometimes ensure that the belt doesn’t turn when not stretched. Also check that the tensioner pulley moves freely, there is a grease nipple for the arm that is often neglected, that could cause it to not fully disengage when lifting the deck.
How can I tighten that middle belt with the geaurd that turns on the blades where's the tensioner
Hi the tensioner is at the back close to the engine on the left side of the machine. It can get stuck if it is not greased properly. I talk about this at 9:25 in this video:
czcams.com/video/MD3V0yRuyoc/video.htmlsi=WAmGNji65ki1n_c0
.hi i have a r15v2 ride on and i got a new belt it should go from the middle pulley to the deck but it seems short im not sure is the belt wrong or im not correctly fitting it is there some where i can a diagarm to show me
Hi! What year is your mower and what cutting deck do you have (timed or not timed etc.) I can find the ipl for you if I get some more info.
@NilsKall hi Nils thank you for getting back to me deck is not timed just an ordinary v belt on it how do I find out the year
@@conormc636 czcams.com/video/JJNkhCavH20/video.htmlsi=Z_BjfM64yNOK-Ui7
Does deck fold up to change blades ?
No not on this model.
Husqvarna rider 155 middle belt is that 55 inches
Hi, what cutting deck do you have?
Cutting deck belt was 65 inches long 1/2 thick
@@NilsKall same as one in video think 42
@@tvbox6075 ok, so then you know the length? This cutting deck is 85 cm wide or about 34 inches.
Husqvarna rider 155 who knows deck size then middle belt size then last belt drive belt size
Rider 155 can be equipped with different cutting decks. I will find a link to the IPL for you. (Illustrated parts list)
This could perhaps help you!
www.yumpu.com/fr/document/read/9171439/ipl-rider-155-usa-2006-01-ride-mower-husqvarna