Thank you so much for the video I installed everything right the thing that I didn’t do was do the reset with the little key to get where the deadbolt would turn. Thank you so much for your video.
Thanks for this! I was wondering if you could look the door from the outside without a key and apparently you can by pressing any number for two seconds. Totally missed this instruction, thank you!
If you're seeing red flashing lights when trying to do any programming, ensure you're entering the master code correctly. The master code must be entered to make programming changes. It also flashes red a 4-5 times if you enter a personal code incorrectly. Also, when the batteries are low you will see a flashing red light.
Hi, please please help me! I installed The key lock All the of lights are flashing and I put the key into the rest and it doesn’t stop, what should I do?
I bought 2 sets of these, the installer didn't save the boxes... Now I have NOTHING to go by... No box, no manual no master code! What can I do? Any ideas? I tried contacting the company but the email cannot be delivered. I can only use the key, no other functions work. I don't know what to do.
See this page. I believe the user guide is the one page cheat sheet (The default master code is at top left of the page.). If you have changed the default Master code and cannot remember it, go through the reset procedure in the user instructions... iveise.com/pages/ks02b-technical-documentation If this is not for your exact model go up to the menu (three lines at top left) - products - fingerprint locks - and select your device.
I think i messed up i put all 4 batteries in and didn't push the reset button in and now the deadbolt just keeps opening and closing by itself... everytime i push a button it just starts opening and closings and now i tried to reset it by taking the batteries out and it does the same thing HELP!!
You have to delete one fingerprint at a time. As follows: = = Master Code = 5 Scan fingerprint When successful, you will see the green light flash and hear a long beep. If the finger is not available, you may need to reset the lock to factory settings: Open the door and ensure it's unlocked. Press and hold the reset button (push a pen/pin into the tiny reset hole underneath the batteries) - while at the same time take out one battery, and then put the battery back in. Keep holding the reset button for about 3 seconds after putting the battery back in - until you hear a beep and see the latch automatically extend. See the video at about 1:24 for help. A factory reset will reset the master code back to 12345678, auto lock will be disabled, silent mode will be disabled, wrong code entry limit will be set to 10 times, shut down time will be set to 3 minutes, and vacation mode will be disabled. This is from my little user guide..
@@Jean78578 i figured it out i didnt do the battery reset correctly once i did that i was able to get green lights the instructions are not the greatest
Red light means whatever you have tried to set up has failed. Re-enter the master code and start fresh. Be sure to follow the exact sequence shown on the colored instruction sheet..
Soo helpful tyvm! Forgot the battery reset
Glad it helped!
Very Helpful! Thank you!
Glad it was helpful!
Thank you so much for the video I installed everything right the thing that I didn’t do was do the reset with the little key to get where the deadbolt would turn. Thank you so much for your video.
Glad I could help!
Thank You. It's so clear and easy from your instructions.
Glad it was helpful!
Very helpful, well done.
Thanks. I'm glad it was helpful!
Omgsh, thank you your video made it so easy!!!!
You're welcome!
Thanks for this! I was wondering if you could look the door from the outside without a key and apparently you can by pressing any number for two seconds. Totally missed this instruction, thank you!
Yes you can! The door lock is pretty awesome..
thank you
Welcome!
My will not reset red light flashes
If you're seeing red flashing lights when trying to do any programming, ensure you're entering the master code correctly. The master code must be entered to make programming changes. It also flashes red a 4-5 times if you enter a personal code incorrectly. Also, when the batteries are low you will see a flashing red light.
How is the battery life? I heard keyless entry with “finger print scanners” drains battery .TIA.
The batteries seem good. We've been on the same batteries from months.
Hi, please please help me! I installed The key lock
All the of lights are flashing and I put the key into the rest and it doesn’t stop, what should I do?
Flashing red lights indicates the batteries are low..
I bought 2 sets of these, the installer didn't save the boxes... Now I have NOTHING to go by... No box, no manual no master code! What can I do? Any ideas? I tried contacting the company but the email cannot be delivered. I can only use the key, no other functions work. I don't know what to do.
See this page. I believe the user guide is the one page cheat sheet (The default master code is at top left of the page.). If you have changed the default Master code and cannot remember it, go through the reset procedure in the user instructions...
iveise.com/pages/ks02b-technical-documentation
If this is not for your exact model go up to the menu (three lines at top left) - products - fingerprint locks - and select your device.
Do you really need to change your deadbolt or can I just use my old one?
If the old one works well, I would leave it.
How do I lock this from the outside without enabling auto lock?
Press any button for a couple seconds..
I think i messed up i put all 4 batteries in and didn't push the reset button in and now the deadbolt just keeps opening and closing by itself... everytime i push a button it just starts opening and closings and now i tried to reset it by taking the batteries out and it does the same thing HELP!!
Try leaving the batteries out for a couple minutes, then, doing the reset procedure..
@@Jean78578 I did but still doing the same thing
Do you happen to know how to delete all fingerprints off? Or reset it?
You have to delete one fingerprint at a time. As follows:
=
=
Master Code
=
5
Scan fingerprint
When successful, you will see the green light flash and hear a long beep.
If the finger is not available, you may need to reset the lock to factory settings:
Open the door and ensure it's unlocked.
Press and hold the reset button (push a pen/pin into the tiny reset hole underneath the batteries) - while at the same time take out one battery, and then put the battery back in.
Keep holding the reset button for about 3 seconds after putting the battery back in - until you hear a beep and see the latch automatically extend.
See the video at about 1:24 for help.
A factory reset will reset the master code back to 12345678, auto lock will be disabled, silent mode will be disabled, wrong code entry limit will be set to 10 times, shut down time will be set to 3 minutes, and vacation mode will be disabled.
This is from my little user guide..
Help...mine is just showing red all the time
It will show red whenever an invalid command is entered or an invalid master code..
im not getting any green lights
To do any programming, you first have to enter the correct master code.
@@Jean78578 i figured it out i didnt do the battery reset correctly once i did that i was able to get green lights the instructions are not the greatest
Fabulous!
Should i unplug it and start all over
Red light means whatever you have tried to set up has failed. Re-enter the master code and start fresh. Be sure to follow the exact sequence shown on the colored instruction sheet..
I tried that, even went as far as Unplugging the unit and started over. No good. UGH