Awesome video! Was looking for something short and concise that included the major steps for beginners and this was perfect! Thanks for sharing your expertise with us.
Thank you, I was already familiar with FDM printing but I had only a vague clue how resin printers worked, this was a great introduction on the subject.
You should not put the printer next to a window if the temperature outside differs alot from indoor temperature. And usually most gases is produced while curing.
when cleaning, do we use only isopropyl alcohol, or can we add something to the mix because i dont have much isopropyl alcohol and i dont want to waste the whole bottle on the first print
Question: I have a new Elegoo Saturn 12K printer and for small jobs, or jobs placed in the center of the plate, all is good. I've even run two exposure test prints that came out great. What I would like to do is place multiple parts on the plate at once, to save time on large multi-part projects. BUT, these seem to fail most of the time. Is it best practice to do one part at a time, in the center or is there a good way to do multiple parts at once? Thanks.
Love the video and I basically got the exact setup based on your recommendations. Things are going really well, but I was curious which glue you use for resin. Often I have difficulty using my usual gorilla super glue.
@Darkwing5380 you can recycle it at an extraction rate of 90% by leaving the sealed container of alchohol in a transparent bin out in the sun, after 3 days the resin will cure and settle to the bottom, from there you extract the clean alchohol and leave behind the cured residue at the bottom for cleaning out separately. If you have to dump it, ask your local dump where that is possible, some dumps have disposal for volatile chemicals.
My resin parts just won't line up seamlessly always a big separation I've used the cones of calibration dialled in perfectly yet NONE of my pieces meet together 😢 yes I'm brand new to resin printers only owned fdms, where am i going wrong is they test prints somewhere that help line ups?
Was trying to find it myself. From a bit of digging around it looks like Akfix 705. Closest I could find that matched the couple of shots it's in the video. Good reviews but haven't tried it out yet.
hey great video! I want to buy a 3d printer to print that kind of figures and even bigger size (but with the same quality), I am between Anycubic M3 Premium / Anycubic M5s / Elegoo Saturn 3 Ultra. I like the print volume of Elegoo, which one do you think will be the better fit for prints like the one you showed it the video? Thank you
Yeah, don't bother with the free model. It does not work anymore. The link just takes your email address and never sends you the model. Been waiting for days now, safe to say it's broken.
0:24: He's a "MACHINACAL" engineer?! 🤣😂🤣 Dude, I'm liking your video buuuuuttt... is this how you speak to people IRL? My suggestion for your future vids is just speak naturally. That would be great. Thanks!
OK video, but your free model site just takes a person email and doesn't send the link for the download. So that's pretty sketchy feeling.
Awesome video! Was looking for something short and concise that included the major steps for beginners and this was perfect! Thanks for sharing your expertise with us.
This is super inspiring, cool that the printer is so cheap. Hard to believe it prints via screen exposure. Almost an extension to photography.
Thanks Thumbnail Grail !
I am so glad I'm watching this before purchasing one
Heck yeah man! Fantastic video!
Thanks Uncle Jessy!
(I'm the one Ty from TableFlip Foundry was messaging you about! Check your email from austen@crate3d.com if you get the chance!)
🤟
How does a verified yter only have 2 likes after 2 years thats crazy
Brand new to 3d printing and you simplified a lot for me!
Thank you, I was already familiar with FDM printing but I had only a vague clue how resin printers worked, this was a great introduction on the subject.
Wow finally a super good video to give me some real and informed basics.
Thank you very much
Great video. The link for free file no longer works... :(
You should not put the printer next to a window if the temperature outside differs alot from indoor temperature. And usually most gases is produced while curing.
I am very new at 3D printing and if you can, it would be very helpful if you could put out a video of how to support your design! 😊
when cleaning, do we use only isopropyl alcohol, or can we add something to the mix because i dont have much isopropyl alcohol and i dont want to waste the whole bottle on the first print
That godlike quality
good video good & clear infokeep up the good work
Thank you!
Hello! What tools would you use to do engravings in PLA after the print is done?
Question: I have a new Elegoo Saturn 12K printer and for small jobs, or jobs placed in the center of the plate, all is good. I've even run two exposure test prints that came out great. What I would like to do is place multiple parts on the plate at once, to save time on large multi-part projects. BUT, these seem to fail most of the time. Is it best practice to do one part at a time, in the center or is there a good way to do multiple parts at once? Thanks.
Love the video and I basically got the exact setup based on your recommendations. Things are going really well, but I was curious which glue you use for resin. Often I have difficulty using my usual gorilla super glue.
hello can you share your configuration of supports and lychee please,you can export, I have tried many times and they usually leave a lot of marks.
What do you do with the dirty alcohol? Can you reuse it or do you have to dump it somewhere and buy more? If you have to dump it, how/where?
I have this question too would love to know the answer.
@Darkwing5380 you can recycle it at an extraction rate of 90% by leaving the sealed container of alchohol in a transparent bin out in the sun, after 3 days the resin will cure and settle to the bottom, from there you extract the clean alchohol and leave behind the cured residue at the bottom for cleaning out separately. If you have to dump it, ask your local dump where that is possible, some dumps have disposal for volatile chemicals.
@@miguellopez3392 Thank you for your response. I’m looking at getting into resin printing, so I will definitely keep this in mind when I do.
@@Darkwing5380 keep in mind that if you get water washable resin, it is still not safe to dispose of that waste water in a sink.
@@miguellopez3392 Absolutely, thank you for the information. 💙
My resin parts just won't line up seamlessly always a big separation I've used the cones of calibration dialled in perfectly yet NONE of my pieces meet together 😢 yes I'm brand new to resin printers only owned fdms, where am i going wrong is they test prints somewhere that help line ups?
What superglue and activator were used, I'm not seeing anything linked?
Was trying to find it myself. From a bit of digging around it looks like Akfix 705. Closest I could find that matched the couple of shots it's in the video. Good reviews but haven't tried it out yet.
I just bought a creality-mage 8k
Great info! But staying away from Esty. Takes 25% of total sales
was the 'machinacal' engineer on purpose? nice one, if so haha
How do you get all those small parts to fit during assembly, with no gaps?
I tried to download the file and couldn’t. It was greyed out .
Any good slicing software is going to have good auto support functionally
I'm looking to get one it was gonna be tue photon x, I need one for my armour modelling hobby b9g time!
hey great video!
I want to buy a 3d printer to print that kind of figures and even bigger size (but with the same quality),
I am between Anycubic M3 Premium / Anycubic M5s / Elegoo Saturn 3 Ultra.
I like the print volume of Elegoo, which one do you think will be the better fit for prints like the one you showed it the video? Thank you
Would printing trains be the same?
where are the links to your friends work?
He said on screen that he is a "Machanical engineer". Does he mean mechanical?
free file? after you sign up for some bs
yeah thats some bad shizz right there
Was wondering why I get a headache when I print
whats the name of hiphop beat :D
Shame that it is mainly an advertising video for friends / sponsors.
Rami Malek
guys use water washable resin non toxic and cheaper can handle with hands use just water
@mariarzyt definitely true!
Yeah, don't bother with the free model. It does not work anymore. The link just takes your email address and never sends you the model. Been waiting for days now, safe to say it's broken.
Free model has popups that don’t allow anything and can’t be accessed, very deceiving
0:24: He's a "MACHINACAL" engineer?! 🤣😂🤣 Dude, I'm liking your video buuuuuttt... is this how you speak to people IRL? My suggestion for your future vids is just speak naturally. That would be great. Thanks!
Can you do a giveaway
soon!
Ok thanks
jajajja, you ve just skip the important...
Begginer to expert in 13 minutes? Is this matrix? "i know karate"? this is just an overview
IPA is toxic? Maybe if you drink it or pour it in your eyes. But for casual contact its not anywhere near the word 'toxic'.